Abstract:There are heat transfer correlations for heat transfer analysis in single tube geometries after several experimental and theoretical heat transfer studies in these single tube geometries. This is not the case for heat transfer analysis in rod bundle geometry with regard to proposed square fuel assembly of the Supercritical-Water-Cooled Reactor (SCWR) European Atomic Energy (EURATOM) design. Thus limited heat transfer studies exist on rod bundle geometry at supercritical pressures. Heat transfer correlations with accurate prediction capabilities of coolant and wall temperatures will be helpful in carrying out heat transfer studies at supercritical pressures. This paper presents the performance of twelve selected heat transfer correlations assessed on the 1/8th bare square fuel assembly of the SCWR EURATOM design using Simulation of Turbulent flow in Arbitrary Regions Computational Continuum Mechanics C ++ based code (STAR-CCM + CFD code). The obtained numerical results were compared with the results obtained by Waata numerical experimentation. Overall, the Cheng et al. correlation provided the most satisfying prediction for the wall temperatures in all the sub-channels and captured closely Wataa's Numerical data. The maximum wall temperature was obtained in sub-channel 9, the hottest sub-channel and exceeded the design limit 620 °C by 60 °C for the Cheng correlation. The difference in temperature between the hottest and coldest sub-channels 9 and 1 respectively was approximately 80 °C. It was found that Cheng correlation is best suited for heat transfer prediction in rod bundle geometry at supercritical pressures with regard to the proposed square fuel assembly of the SCWR EURATOM design. It was also found that the different numerical tools adopted for this study and Waata study were able to capture the trends of normal, enhanced and deteriorated heat transfer regimes normally observed at supercritical pressures. Nevertheless, experimental investigations involving rod bundles adopted in this study should be conducted to validate the results obtained numerically and address the inconsistency of the conclusions drawn when compared with Waata data and other similar studies.

Development of Sub-Channel Code SACoS and Its Application in Coupled Neutronics/thermal Hydraulics System for SCWR

Development of sub-channel analysis code for CANDU-SCWR

Preliminary study on physical characteristics of single‐pass super‐critical water‐cooled reactor core

Numerical Verifications on Heat Transfer to Supercritical Water Flowing Upward in a 4-m Long Bare Vertical Tube

Development and Verification of Multiphysical Coupling Calculation Code for Typical Pressured Water Reactor Core

NUMERICAL INVESTIGATION ON HEAT TRANSFER TO SUPERCRITICAL WATER FLOWING UPWARD IN A 4-M LONG BARE VERTICAL CIRCULAR TUBE

Thermal Hydraulic Review of Light Water Reactor Based on Subchannel Code CTF

Development of modular dynamic code for steam power conversion system in sodium-cooled fast reactor

A Review of CFD Advancements Toward Thermal-Hydraulic Analysis of Prototypical Flow Conditions in PWR Subchannels

Thermal-Hydraulic Analysis For Experimental Device Of Supercritical Water Reactor-Fuel Qualification Test

Experimental study on heat transfer in vertical cooling tube cooled by downward flow in the passive heat removal system of SCWR

Development of system analysis code and its application in transient simulation of supercritical CO 2 Brayton cycle direct cooled reactors

Neutronics and Thermal-Hydraulics Coupling Analysis in Accelerator-Driven Subcritical System

Development of MCBurn and its application in the analysis of SCWR physical characteristics

Coupled Monte Carlo and Thermal-Hydraulics Modeling for the Three-Dimensional Steady-State Analysis of the Xi'an Pulsed Reactor

Assessment of heat transfer correlations in the sub-channels of proposed rod bundle geometry for supercritical water reactor

The prospect of the modeling simulation for the passive containment cooling system of the advanced PWR in China

Development and Application of Multi-Physics Safety Analysis Code for Advanced Liquid Metal Cooled Reactor

Development and validation of ARSAC-CORTH coupling code based on a generic coupling architecture

Numerical Study and Assessment of a Novel Combined Passive Cooling System for Tank-in-pool Reactors

Modeling and program development of supercritical CO 2 sub-channel based on Modelica language