Abstract:With the development in additive manufacturing, the use of surface treatments for gas turbine design applications has greatly expanded. An experimental investigation of the pressure loss and heat transfer characteristics within impingement jet arrays with arrays of target surface micro cooling units is presented. The discharge coefficient and Nusselt number are measured and determined for an evaluation of the pressure loss of the flow system and heat transfer level, respectively. Considered are effects of impingement jet Reynolds number ranging from 1000 to 15,000 and micro cooling units (square pin fin) height (h) with associated values of 0.01, 0.02, 0.05, 0.2, and 0.4 D, where D is the impingement hole diameter. Presented are variations of Nusselt number, and Nusselt number ratio, discharge coefficient, discharge coefficient ratio, discharge coefficient correlation. Depending upon the micro cooling unit height, discharge coefficient ratios slightly decrease with height, and the ratio values generally remain unit value (1.0). When Rej = 1000 and 2500 for several cooling units height values, discharge coefficient ratios show the pressure loss decreases about 2–18% and 3–6%, respectively, when compared to the data of a baseline smooth target surface plate. The observed phenomenon is due to the effects of flow blockage of micro cooing units, local flow separation, and near-wall viscous sublayer reattachment. Results also show that heat transfer levels increase 20–300% for some of the tested toughened target surface plates when compared to smooth target surface plates. The heat transfer level enhancement is because of an increase in thermal transport and near-wall mixing, as well as the increased wetted area. In addition, micro cooling units elements break the viscous sublayer and cause greater turbulence intensity when compared to the smooth target surface. Overall, results demonstrate that the target surface micro cooling units do not result in a visible increment in pressure loss and reduce pressure loss of the flow system for some of the tested patterns. Moreover, results show the significant ability of micro cooling units to enhance the surface heat transfer capability of impingement cooling relative to smooth target surfaces.

Experimental investigation of submerged single jet impingement using Cu–water nanofluid

Experimental Investigation Of Submerged Impinging Jet Using Cu-Water Nanofluid

Heat transfer performance of Cu-water nanofluids in the jet arrays impingement cooling system

A Review on Experimental and Numerical Investigations of Jet Impingement Cooling Performance with Nanofluids

Experimental and Numerical Investigation of Flow Structure and Heat Transfer Behavior of Multiple Jet Impingement Using MgO-Water Nanofluids

Convective heat transfer and flow characteristics of Cu-water nanofluid

Experimental study on transient and steady-state impinging jet cooling condition with TiO2-Water nanofluids

Thermal and hydraulic characteristics of a single reverse nanofluid jet in a double-wall cooling configuration

Artificial neural network and numerical analysis for performance enhancement of hybrid microchannel-pillar-jet impingement heat sink using Al2O3-water and CuO-water nanofluids

The Hydraulic Cavitation Affected by Nanoparticles in Nanofluids

Property of Water-Nanoparticle Flow and Heat Transfer in the Double-Tube Heat Exchanger with Nanofluid

Experimental Study on the Convective Heat Transfer of Cuo-Water Nanofluid in A Turbulent Flow

Experimental study on the heat transfer of moving double jet impingement during steel quenching

Experimental Investigation on Flow and Convective Heat Transfer Feature of A Nanofluid for Aerospace Thermal Management

Experimental Investigation of Micro Cooling Units on Impingement Jet Array Flow Pressure Loss and Heat Transfer Characteristics

Experimental investigation of effect of iron oxide nanofluids with different morphology on heat transfer of multiple impinging jets

Pulsating nanofluid-jet impingement cooling and its hydrodynamic effects on heat transfer

Flow behavior and heat transfer characteristics of liquid film on vertical hot surface by inclined jet impingement

Experimental and parametric study in pool boiling enhancement with self-induced jet impingement on the microporous copper surface using R1336mzz(Z)

Numerical study on jet impingement boiling cooling of nose cone

Multi-objective optimization of a hybrid nanofluid jet impinging on a microchannel heat sink with semi-airfoil ribs based on field synergy principle