Abstract:With the increasing demand of the electricity, an efficiency improvement and thereby a reduced CO2 emission of the coal-fired plants are expected in order to reach the goal of the Kyoto protocol. In the medium term, increase of thermal efficiency of the steam cycle can be achieved by a rise of the process parameters. Currently, live steam pressures and temperatures up to 300 bar and 923 K are planned as a next step. This means an increase of 50-100 K in comparison to plants presently under operation. Such a large increase will only be possible, if all thermally high loaded components of the plant are made of new materials and/or new technologies for cooling and thermal insulation are applied.Closed circuit steam cooling of blades and vanes in modern steam turbines is a promising technology in order to establish elevated live steam temperatures in future steam turbine cycles. Due to the cooling of the components, materials can be used, which are common in todays application. In this paper, a steam-cooled test vane in a cascade with external hot steam flow is analysed numerically by applying a Conjugate Calculation Technique. The boundary conditions of the hot steam are derived from the planned inlet parameter of the HP steam turbine in a medium term and a long term in order to show the application potential of such a cooling technique. The supply steam parameters of the cooling are set equal to those of the outlet steam from the HP steam turbine.The results show that the steam cooling technique can reach necessary cooling effectiveness in the steam turbine by using only minor amounts of cooling steam. The internal pan of the vane is cooled homogeneously in both investigated cases. Basic features and phenomena of the steam cooling technique in steam turbines are discussed in the paper with respect to future application. It has been found that the trailing edge region of the steam-cooled vane is less critical with respect to high thermal load than in gas turbine application with the same configuration. At the leading edge of the vane, high thermal load can be detected because of the direct impingement of the hot steam. Improvement of the leading edge cooling is recommended by increasing cooling steam amount for the leading edge channel. Thus, a larger diameter of the channel can increase internal cooling efficiency for the leading edge. Due to the different heat transfer characteristics on the suction side and pressure side, the suction side shows also a higher temperature distribution in the investigated cases.

Test Study on Aerodynamic Performance of Large-enthalpy Drop Stator of Steam Turbine Cascade

Large Eddy Simulation and CDNS Investigation of T106C Low-Pressure Turbine

Les and Cdns Investigation of T106c Low Pressure Turbine

Comparative Experimental Investigation On Aerodynamic Performance Of A Steam Turbine Cascades, Part Ii - Stator Vanes

Numerical Study of the Secondary Flow in Steam Turbine Static Cascade under Varying Conditions

Investigation of the Steam-Cooled Blade in a Steam Turbine Cascade

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Design of a Sector Cascade Applied in the Middle Stage of a Compressor Test Rig

Cooling Performance Of The Steam-Cooled Vane In A Steam Turbine Cascade

Comparative Experimental Investigation on Aerodynamic Performance of Steam Turbine Cascades, Part I - Rotor Blades

Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence

The Blade Curving Effects in a Turbine Stator Cascade With Low Aspect Ratio

Analysis of the Mechanism Governing the Migration of Boundary Layers in a Highly-loaded Turbine Cascade Controlled By Using Bowed Blades

An Experimental Investigation of Endwall Heat Transfer and Aerodynamics in a Linear Vane Cascade

Distribution Characteristics of High Wetness Loss Area in the Last Two Stages of Steam Turbine under Varying Conditions

Experiment and Numerical Simulation of the Performance on Scaled Compressor Cascade and Development of a Prediction Model

Effect of Leakage Flow on the Endwall Cooling Performance in High Subsonic Turbine Cascade

Numerical study on aerodynamic performance and particle erosion characteristics of flue gas turbine

Study on the Tip Leakage Loss Mechanism of a Compressor Cascade Using the Enhanced Delay Detached Eddy Simulation Method

Numerical Investigations about the Aerodynamic Performance of the Cascade in Unsteady Environment

Wind Tunnel Testing and Modeling Implications of an Advanced Turbine Cascade