Abstract:Three crosslinkers, poly(ethylene glycol) diacrylate (PEGDA), glycerol ethoxylate triacrylate (GETA) and citric acid-(PEG acrylate)3 (CA-PEGTA) derived from poly(ethylene glycol) (PEG) were synthesized at first. The three series of poly (N-isopropylacrylamide) (PNIPAAm) hydrogels were prepared by photopolymerization with the crosslinkers and compared with a hydrogel based on commercial crosslinker, N,N′-methylene bis-acrylamide (NMBA). The influence of the crosslinker structures and contents on the swelling behaviour, mechanical properties, and drug release of the hydrogels was investigated. The results showed that the hydrogels based on PEGDA and NMBA exhibited the highest and the lowest swelling ratio, respectively. The content of crosslinker of all hydrogel series showed good thermosensitivity and thermo-reversibility. The critical gel transition temperature (CGTT) appeared at 32 °C for the hydrogel based on NMBA, but appeared at about 34 °C for other hydrogels due to higher hydrophilicity of the crosslinker. In the mechanical properties, three-arms crosslinker GETA and CA-PEGTA led to higher mechanical strength than a linear crosslinker PEGDA. A hydrogel based on GETA (NG6) showed the highest shear modulus of 656.9 kPa and Young's modulus of 1655.0 kPa. The hydrogels containing higher content of crosslinker revealed lower swelling ratio and higher mechanical strength. In the drug release, the hydrogels with higher swelling ratios showed higher drug absorbed. The highest release percentage of caffeine and vitamin B12 for hydrogel based on PEGDA (NP6) could reach 68.3% and 75.4%, respectively. In addition, the bound water and toxicity of the hydrogels were also investigated.

Thermo-sensitive and separation properties of poly(N-isopropylacrylamide) hydrogels with enhanced surface crosslinking

DEVELOPMENT OF POLY (N-ISOPROPYLACRYLAMIDE)IN SEPARATION SYSTEMS

Thermosensitive Poly(N-isopropylacrylamide-co-acrylonitrile) Hydrogels with Rapid Response

Synthesis and Properties of the Semi-Interpenetrating Polymer Network-Like, Thermosensitive Poly(N-Isopropylacrylamide) Hydrogel

Fabrication of Fast Responsive, Thermosensitive Poly(n-Isopropylacrylamide) Hydrogels by Using Diethyl Ether As Precipitation Agent.

Refined control of thermoresponsive swelling/deswelling and drug release properties of poly(N-isopropylacrylamide) hydrogels using hydrophilic polymer crosslinkers

Fabrication and characterization of microgel-impregnated, thermosensitive PNIPAAm hydrogels

Effect Of Mixed Solvents On Characteristics Of Poly(N-Isopropylacrylamide) Gels

Synthesis and Characterization of Thermosensitive Hydrogel

Thermoresponse improvement of poly(N-isopropylacrylamide) hydrogels via formation of poly(sodium p-styrenesulfonate) nanophases.

Strategy to introduce a pendent micellar structure into poly(N-isopropylacrylamide) hydrogels.

Thermo-induced Formation of Physical “Cross-Linking Points” of PNIPAM-g-PEO in Semidilute Aqueous Solutions

Synthesis of Temperature-Sensitive Poly(N-isopropylacrylamide) Hydrogel with Improved Surface Property

Poly(N-Isopropylacrylamide) Hydrogels Crosslinked by Small-Molecular Crosslinkers Through Click Chemistry

Effect of poly(ethylene glycol)-derived crosslinkers on the properties of thermosensitive hydrogels

Synthesis and Properties of Thermosensitive, Crown Ether Incorporated Poly(n-Isopropylacrylamide) Hydrogel

Effect of Hydrophobic Polystyrene Microphases on Temperature-Responsive Behavior of Poly(n-Isopropylacrylamide) Hydrogels

Synthesis of temperature sensitive PNIPAAm cryogels in organic solvent with improved properties

Effect of the crosslinking level on the properties of temperature-sensitive poly(N-isopropylacrylamide) hydrogels

Synthesis, Characterization and Swelling Kinetics of Thermoresponsive Pam-G-Pva/Pvp Semi-Ipn Hydrogels