Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Application of the HDMR Method in Simulating Homogeneous Ignition with Detailed Chemistry

Comparison of Kinetic Mechanisms for Numerical Simulation of Methanol Combustion in DICI Heavy-Duty Engine

Numerical Simulation of HCCI Engine with Multi-Stage Gasoline Direct Injection Using 3D-CFD with Detailed Chemistry

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Detailed Numerical Simulation of Transient Mixing and Combustion of Premixed Methane/air Mixtures in a Pre-Chamber/main-chamber System Relevant to Internal Combustion Engines

Numerical Simulation of Gasoline Stratified Charge Compression Ignition Using 3D-CFD Coupled with Detailed Chemistry

Numerical Simulation of Chemical Kinetics Mechanism in HCCI Combustion Fueled with Dimethyl Ether

NUMERICAL SIMULATION OF HCCI COMBUSTION WITH DME/LPG BLENDED FUEL

Numerical Methods for Complicated Chemical Mechanism Involved in Combustion Simulation

Study of dimethyl ether homogeneous charge compression ignition combustion process using a multi-dimensional computational fluid dynamics model

Direct Numerical Simulations and Analysis of Three-Dimensional N-Heptane Spray Flames in a Model Swirl Combustor

Direct numerical simulation of DME auto-ignition with temperature and composition stratification under HCCI engine conditions

Application of the Projective Method in the Numerical Simulation of Combustion

Numerical Study on Three-Stage Ignition of Dimethyl Ether by Hot Air under Engine-Relevant Conditions

Experimental And Numerical Study On Auto-Ignition And Combustion Of Homogeneous Charge Compression Ignition Fueled With Dimethylether

An Alternative Approach to Accommodate Detailed Ignition Chemistry in Combustion Simulation

Toward Efficient Chemistry Calculations in Engine Simulations Through Static Adaptive Acceleration

Modeling of HCCI combustion: From 0D to 3D

Numerical Simulation of Homogeneous Charge Compression Ignition Combustion Using A Multi-Dimensional Model

Multi-dimensional Modeling of the Application of Catalytic Combustion to Homogeneous Charge Compression Ignition Engine

Kinetic Modeling Study of Homogeneous Ignition of Dimethyl Ether/hydrogen and Dimethyl Ether/methane