Abstract:RAFT polymerization is a type of psudo-living radical polymerization. In order to synthesize high pure block copolymers by RAFT polymerization, it is desirable to suppress the irreversible termination which may result in the formation of dead chains. For polymers less than 5 x 10(4) g/mol, the dead chain fraction could remain to be lower than 0.1 by reducing the initiator concentration. In the synthesis of block copolymers, the dead chains formed in the first stage are actually contaminant. Targeting to the synthesis of high pure block copolymers with high molecular weight using RAFT polymerization, we studied the copolymerization of butyl acrylate and styrene mediated by 1-phenylethyl phenyl-dithioacetate (PEPDTA) as a RAFT agent. The influences of the type of initiators (AIBN (2-2'-azobis ( isobutyronitrile)), ACC ( 1-1'-azobis ( cyclohexane-carbonitrile)), the concentrations of initiator and polymerization temperature on the copolymerization kinetics and molecular weight and its distribution were investigated. When AIBN was used, the polymerization would stop at middle monomer conversion, which limited the increase of molecular weight of the copolymer if we reduced the initiator concentration. It was found that only with the initiator (ACC) with small decomposition rate constant and high polymerization temperature, the block copolymer with high molecular weight and small fraction of dead chains ( < 0.1) could be synthesized. The reason for these quite strict requirements is that the initiator concentration should remain far below that of the conventional radical polymerization, which is limited by the very low RAFT concentration.

Synthesis of Hammer-Like Macromolecules of C60 with Well-Defined Polystyrene Chains Via Atom Transfer Radical Polymerization (ATRP) Using a C60-monoadduct Initiator

One‐step Synthesis of Hyperbranched Polyethylene Macroinitiator and Its Block Copolymers with Methyl Methacrylate or Styrene Via ATRP

Synthesis of C-60-End-Bonded Polymers with Designed Molecular Weights and Narrow Molecular Weight Distributions Via Atom Transfer Radical Polymerization

Synthesis of Well-Defined Polystyrene with Molar Mass Exceeding 500 kg/mol by RAFT Emulsion Polymerization

Synthesis of A Well-Defined Hammer-Like C-60 Conjugated Poly (2-Hydroxyethyl Acrylate) and Its Self-Assembly in Water

Synthesis of C60 End-Capped Polymers from Azide Functional Polystyrene Via Atom Transfer Radical Polymerization

The Synthesis of High Molecular Weight Block Copolymers by Raft Polymerization

Synthesis of C-60-End-Bonded Narrow Polydispersity Polystyrene Via Atom Transfer Radical Polymerization

The Morphology Investigation of Hammer-Like C-60 Conjugated Polystyrene in Solution

Synthesis of Hyperbranched Polystyrene and Its Fullerene End-capped Derivatives with Multifunctional Atom Transfer Radical Polymerization Initiator

Hydrophilic Modification of Well-Defined Hammer-Shaped C-60-Ps and the Self-Assembly Behavior Therefrom

Synthesis of Poly(Methyl Methacrylate)-Graft-Polystyrene by Atom Transfer Radical Polymerization

One‐pot Synthesis of Well‐defined Multiblock Polymer: Combination of ATRP and RAFT Polymerization Involving Cyclic Trithiocarbonate

Dispersion Atom Transfer Radical Polymerization of Vinyl Monomers in Supercritical Carbon Dioxide

Enhancing Initiation Efficiency in Metal-Free Surface-Initiated Atom Transfer Radical Polymerization (SI-ATRP)

Transition metal catalyzed atom transfer radical polymerization in the presence of a conventional radical initiator

Advances in Organocatalyzed Atom Transfer Radical Polymerization

Kinetic Modeling of Surface-Initiated Atom Transfer Radical Polymerization

Uniform Polymer Microspheres by Photoinduced Metal‐Free Atom Transfer Radical Precipitation Polymerization

Surface Modification of Polystyrene Latex Particles Via Atom Transfer Radical Polymerization

Highly active copper-based catalyst for atom transfer radical polymerization.