Abstract:In order to gain a better understanding of the membrane's role in the whole process of mass-transfer in membrane gas–liquid contacting systems, PVDF microporous hollow fiber membranes have been fabricated using three different dope solutions containing N-methyl-2-pyrrolidone (NMP) and different additives. The resultant hollow fibers with different structures were used to make membrane modules, which were then applied as gas–liquid membrane contactors for CO2 absorption in water. The membranes were characterized and the effect of membrane structure on the mass-transfer was analysed accordingly.It was found that the additives used imposed a significant effect on the final membrane structure under the same spinning conditions. Compared with distilled water, phosphorous acid and glycerol showed a stronger pore-inducing ability. As a result, the membrane #1 or #2 made by the dope with phosphorous acid or glycerol as an additive had a larger pore size and a higher value of MWCO. The finger-like pores also occupied a larger portion on the membranes #1 and #2 than on the membrane #3, which used distilled water as an additive. Moreover, the membranes #1 and #2 presented a much wider pore size distribution than the membrane #3.The different membrane structures turned out to affect CO2 absorption performance when used as contactors. Since the ratio of the membrane resistance over the overall mass-transfer resistance was increased in the order of #1<#2<#3, with respect to the reductions of MWCO and the finger-like pore portion of these three membranes in the same sequence, the CO2 absorption performance was in the sequence of #1>#2>#3. In addition, it was noticed that all the membranes exhibited considerable membrane resistances from 22% to 36% though the model system used was pure CO2 absorption in distilled water. The partial wetting was probably caused by the capillary condensation of water vapour in the membrane pores instead of water penetration, as the experiment shows that the CO2 flux of three PVDF membranes was kept almost unchanged over 15 days of operation. In comparison with a commercial double skin layer PVDF membrane, it was found that the membrane with an inner skin-free structure plus a porous substrate is favourable to be used in the membrane gas–liquid contacting process.

Wetting of polypropylene hollow fiber membrane contactors

Investigation of Membrane Wetting in Different Absorbents at Elevated Temperature for Carbon Dioxide Capture

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

Effectiveness of a Coagulation Step and Polyester Support on Blend Polyvinylchloride Membrane Formation and Performance

Fabrication and Characterization of Superhydrophobic Polypropylene Hollow Fiber Membranes for Carbon Dioxide Absorption

Surface Modification of Polypropylene Microporous Membranes by the Adsorption of Non-Ionic Surfactants

Effect of Membrane Structure on Mass-Transfer in the Membrane Gas–liquid Contacting Process Using Microporous PVDF Hollow Fibers

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Non-Solvent Influence of Hydrophobic Polymeric Layer Deposition on PVDF Hollow Fiber Membrane for CO2 Gas Absorption

Surface Modification of Polyethylene Membrane by Adsorption of Tween 20 to Improve Antifouling Characteristics in a Bioreactor

On co 2 absroprtion using absorbent in hollow fiber membrane contactor

Surface modification of poly(vinylidene fluoride) hollow fibre membranes for biogas purification in a gas-liquid membrane contactor system.

Surface Modification of Polypropylene Macroporous Membrane to Improve Its Antifouling Characteristics in a Submerged Membrane-Bioreactor: H(2)O Plasma Treatment.

Thermo-responsive Stick-Slip Behavior of Advancing Water Contact Angle on the Surfaces of Poly(n-Isopropylacrylamide)-grafted Polypropylene Membranes

Study of modified PVDF membranes with high-capacity adsorption features using Quantum mechanics, Monte Carlo, and Molecular Dynamics Simulations

Surface Modification Of Uhmwpe/Fabric Composite Membrane Via Self-Polymerized Polydopamine Followed By Mpeg-Nh2 Immobilization

Diverse Morphologies of PVDF Hollow Fiber Membranes and Their Performance Analysis As Gas/liquid Contactors

A new superhydrophobic polypropylene hollow fiber membrane preparation method and its application in the treatment of brine with high salt concentration

Effect of Non-Solvent Additive Concentration on CO2 Absorption Performance of Polyvinylidenefluoride Hollow Fiber Membrane Contactor

Improvement of the Antifouling Characteristics for Polypropylene Microporous Membranes by the Sequential Photoinduced Graft Polymerization of Acrylic Acid

Fabrication and Characterization of Poly(vinylidene Fluoride)–polytetrafluoroethylene Composite Membrane for CO2 Absorption in Gas–liquid Contacting Process