Probe beam deflection study of cupric hexacyanoferrate colloid doped polypyrrole film modified electrode in different electrolytes

Changwei Liu,Guangjin Cheng,Jinghong Li,Juguang Jin,Shaojun Dong

DOI: https://doi.org/10.1016/0022-0728(95)04497-3

IF: 4.598

1996-01-01

Journal of Electroanalytical Chemistry

Abstract:null

What problem does this paper attempt to address?

Probe Beam Deflection Study of the Ion Exchange Between Prussian Blue Film or Indium Hexacyanoferrate Film and Electrolyte Solutions

GJ Cheng,CW Liu,JH Li,JG Jin,SJ Dong

IF: 3.1

1996-01-01

Chemical Research in Chinese Universities

Abstract:Probe beam deflection(PBD) technique together with electrochemical techniques such as cyclic voltammetry was used to study the ion exchange in prussian blue(PB) film and its analogue indium hexacyanoferrate (InHCF) chemically modified electrodes, The ion exchange mechanism of PB was verified as following: K2Fe2+FeI(CN)(6)(-e--K+)reversible arrow(+e-+K+)KFe(3+)Fe(I)(CN)(6)(-xe--xK+)reversible arrow(+xe-+xK+) [Fe3+FeI(CN)(6)](x)[KFe3+FeI(CN)(6)](1-x) where on reduction in contact with an acidic KCl electrolyte, H+ enter PB film before K+. Both the cations and anions participate concurrently in the redox process of InHCF, meanwhile K+ ion plays a major role in the whole charge transfer process of this film with increasing radii of anions.
Probing the Electrolyte Transfer in Ultrathin Polypyrrole Films by In Situ X-ray Reflectivity and Electrochemistry

Pirmin H Lakner,Manuel Brinker,Christoph Seitz,Leon Jacobse,Vedran Vonk,Milena Lippmann,Sergey Volkov,Patrick Huber,Thomas F Keller

DOI: https://doi.org/10.1021/acs.langmuir.0c02068

IF: 3.9

2020-11-17

Langmuir

Abstract:This study reports on the potential-induced charge and mass transfer between an ultrathin polypyrrole (PPy) film and an electrolyte by simultaneous in situ X-ray reflectivity (XRR) and electrochemistry (EC) utilizing their sensitivity to electrons. An about 30 nm thin PPy film was deposited on a silicon single crystal by fast potential cycling, providing a dense film of an extraordinary small surface roughness. XRR was recorded from the PPy film in an aqueous 0.1 M perchloric acid at electric potentials between -0.2 V and +0.5 V vs Ag/AgCl. The PPy film shows typical reversible and linear changes in film thickness and electron density arising from the potential-dependent electrolyte incorporation. By introducing EC-XRR, a comprehensive analysis combining in situ XRR and EC, the net number of electrons passing through the PPy-electrolyte interface was deduced along with the potential-induced thickness variations, indicating a complex exchange mechanism. Evidently, along with the anion transfer, parallel charge compensation by protons and a volume and electron compensating counterflow of solvent molecules take place. Complementary time-dependent EC-XRR scans indicate that these exchange mechanisms are individual in two potential ranges. The low actuation along with a high pseudocapacitance suggest the fast potentiodynamically deposited PPy film as a promising supercapacitor material.
Probe Beam Deflection study of Au Nanoparticles Supported into TiO2 Mesoporous Films

Rusbel Coneo Rodriguez,Paula Angelomé,Gabriel Planes,Cesar Barbero,Mariano Bruno

DOI: https://doi.org/10.1002/cnma.202400291

IF: 3.82

2024-06-21

ChemNanoMat

Abstract:Mesoporous thin films modified with nanoparticles of metal (Au) have been used for the fabrication of an ultra‐microelectrode array (UMEA). For the first time, UMEAs were studied using probe beam deflection (PBD) and cyclic voltammetry. The study was carried out using the [Fe(CN)6]3‐/ [Fe(CN)6]4‐ couple as a redox probe. The electrochemical response is that of an array of nanoelectrodes. The effects of scan rate on the current and PBD signal profiles are discussed in the context of mass transport within the pores and at the solution‐electrode interface. The study suggests that the combination of PBD and CV allows a better understanding on the mass transport phenomena in this type of UMEAs of complex architecture.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
Electrochemical Study of a Polypyrrole Film/Decanethiol Self-Assembled Monolayer on a Gold Electrode

J Wang,BZ Zeng,C Fang,F He,XY Zhou

DOI: https://doi.org/10.1002/(sici)1521-4109(199912)11:18<1345::aid-elan1345>3.0.co;2-t

IF: 3.077

1999-01-01

Electroanalysis

Abstract:Cyclic voltammetry and chronoamperometry were used to study the deposition of polypyrrole on a decanethiol self-assembled monolayer modified gold electrode (PPY/SAM/Au). The voltammetric behavior of the PPY/SAM film was investigated in the presence of several different electrolytes. It is found that the SAM shows great influence on the nucleation and growth of the PPY film. The reaction of the SAM and the anions causes the different voltammetric behavior of the polymerization of pyrrole on the modified electrode. Chronoamperometry shows the nucleation and growth of the PPY is initially inhibited but followed by a rapid increase. The SAM also influences electrochemical behavior of PPY film. Experiments show that the SAM can greatly depress the diffusion of anions in the PPY film, and minimize the background capacitance current.
In Situ Preparation and Determination of Electrochemical and Electrochromic Properties of Copper Phthalocyanine-Polyaniline Nanocomposite Films

Mi Ouyang,Xuming Hu,Xiongchao Shao,Lu Chen,Weijun Li,Ru Bai,Ling Zhang,Xiaojing Lv,Alexey Tameev,Cheng Zhang

DOI: https://doi.org/10.1039/c9ra06540g

IF: 4.036

2019-01-01

RSC Advances

Abstract:Copper phthalocyanine (CuPc) films with different morphologies were electrodeposited on the surfaces of ITO electrodes. Then, in each case, a polyaniline (PANI) film was electrochemically polymerized in situ on the surface of the copper phthalocyanine film to form a CuPc-PANI composite film. The electrochemical properties of the CuPc-PANI composite film were observed to be much better than those of the film without CuPc. With the modification involving the CuPc nanowires, the composite film formed a finer particle surface and an increased interface area between the PANI and the electrolyte. Compared to the single-component PANI film, the CuPc-PANI composite film exhibited better performance with a higher optical contrast (58% at 730 nm), a faster response speed (coloring time of 1.02 s, discoloring time of 1.96 s), and better cycling stability (68.71% of the initial electrochemical activity after 500 cycles, in contrast to only about 48.02% for PANI). Moreover, the CuPc-PANI film shows a new feature that can be used as a supercapacitor (specifically a capacitance value of about 5.4 mF cm(-2) at typical currents). Our results demonstrate that the prepared CuPc-PANI composite film is one of the best candidates for multiple potential applications such as high-performance polymer electrochromic materials and supercapacitors.
Colloidal processing of ferroelectric poly(vinylidene fluoride-co-hexafluoropropylene)—ferrimagnetic pseudocapacitive CuFe2O4 composite films

Qinfu Zhao,Xinqian Liu,Stephen Veldhuis,Igor Zhitomirsky

DOI: https://doi.org/10.1007/s00396-022-05022-9

2022-09-12

Abstract:Composite polymer-ceramic films are prepared from colloidal suspensions by electrophoretic deposition (EPD). Co-deposition of ferrimagnetic CuFe 2 O 4 with ferroelectric poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) polymer is achieved using a co-dispersant, which is also used for the preparation of PVDF-HFP particles. The mechanism of co-dispersant adsorption on CuFe 2 O 4 and PVDF-HFP in colloidal suspensions is analyzed. Electrochemical studies of CuFe 2 O 4 reveal good pseudocapacitive properties of this material in a negative potential range, which make it a material of choice for magnetocapacitive devices. A capacitance of 1.72 F cm −2 (43.1 F g −1 ) is observed at 2 mV s −1 for pure material in a neutral Na 2 SO 4 electrolyte. The microstructure and composition of PVDF-HFP-CuFe 2 O 4 films are analyzed. Composite films show ferrimagnetic properties, which are analyzed in a wide temperature range. EPD method represents a versatile strategy for the fabrication of composite films based on functional properties of CuFe 2 O 4 and PVDF-HFP.

polymer science,chemistry, physical
Electrochemical Performance of Electroactive Poly(Amic Acid)-Cu2+ Composites

Ying Yan,Fangfei Li,Ashley M. Hanlon,Erik B. Berda,Xincai Liu,Ce Wang,Danming Chao

DOI: https://doi.org/10.1016/j.apsusc.2016.09.012

IF: 6.7

2017-01-01

Applied Surface Science

Abstract:Electroactive poly(amic acid)-Cu2+ (EPAA-Cu) composites on substrates were successfully prepared via nucleophilic polycondensation followed by the use of an immersing method. Analysis of the structure properties of EPAA-Cu composites was performed using scanning electron microscopy (SEM), X-ray photoelectron spectra (XPS) and Fourier-transform infrared spectra (FTIR). A significant current enhancement phenomenon of EPAA-Cu/ITO electrodes was found as evident from cyclic voltammetry (CV) measurements. In addition, Cu2+ ions were incorporated into the composites and had a positive effect on their electrochromic behaviors decreasing their switching times. The anticorrosive performance of EPAA-Cu composites coatings on the carbon steel in 3.5 wt%NaCl solution were also investigated in detail using tafel plots analysis and electrochemical impedance spectroscopy. The anticorrosive ability of these coatings significantly enhanced through the incorporation of Cu2+ ions. (C) 2016 Elsevier B.V. All rights reserved.
Investigations of electrochemical polymerization processes of thin poly(pyrrole) films and its application to anion sensor based on surface plasmon resonance

Li Tian,Yongjia Feng,Yanjuan Qi,Binbin Wang,Xueyan Fu,Yinran Chen

DOI: https://doi.org/10.1007/s10965-011-9652-0

IF: 3.061

2011-01-01

Journal of Polymer Research

Abstract:A study of the response behavior of anion to surface plasmon resonance (SPR) based sensor, in which a Poly(pyrrole) (Ppy) modified thin gold film was used as a sensor chip is described. In situ surface plasmon resonance and electrochemical methods were used to investigate the electropolymerization and doping/dedoping processes of thin Ppy film. The electropolymerization of pyrrole was carried out under cyclic voltammetric conditions, and simultaneously monitored by in situ SPR. It has revealed that the transition between the reduced state and oxidized state of the Ppy, corresponding to the doping/dedoping of anions, can lead to very distinct changes in SPR signal at a fixed angle of incident laser beam. Furthermore, it has demonstrated that the concentration, the charge and size of anions, as well as the film thickness play important roles in the ingress/egress process of anions. Based on this, this combination of experimental approaches can be used to detect Cl − . SPR signal exhibited a good linear relationship with the concentration of Cl − .
Preparation, Characterization and Electrochemical Properties of Polypyrrole-Polystyrene Sulfonic Acid Composite Film

LT Qu,GQ Shi,C Liu,JY Yuan,WB Qian

DOI: https://doi.org/10.1142/s0256767905000096

2005-01-01

Chinese Journal of Polymer Science

Abstract:Polypyrrole-polystyrene sulfonic acid (PPy-PSSA) composite films have been electrosynthesized in an aqueous solution of PSSA. The electro-active films exhibit cation exchange during the redox process. Infrared, Raman and energy-dispersive spectroscopic results demonstrated that the polyanion of PSS- is co-deposited into the PPy matrix and couldn't be stripped from the film extensively by dedoping, The doping level together with dipolaron content of the PPy-PSSA composite film increases during electrochemical polymerization process. SEM images revealed that the composite film has smooth and compact morphology and AFM pictures suggested that PPy chains are possibly grown perpendicular to the electrode surface. TGA tests indicated that the composite films has much better thermal stability than that of pure PPy. Furthermore, electrochemical studies showed that the relaxation process at certain holding potential has great effect on the shape of the cyclic voltammetric curves of PPy-PSSA composite film. The composite film exhibits cation and anion exchange during the redox process after undergoing the relaxation step. It is more difficult for divalent anion to enter the polymer matrix than a univalent ion, and a large cation such as (CH3CH2CH2CH2)(4)N+ cannot be involved in the ion exchange process.
Preparation and Electrochemical Property of Copper Cobalt Hexacyanoferrate Hybrid Film

LI Hui,HAO Xiao-gang,DUAN Dong-hong,ZHANG Zhong-lin,MA Xu-li,LIU Shi-bin,H LI,X HAO,X MA,S LIU

DOI: https://doi.org/10.3969/j.issn.1001-3849.2009.03.002

2009-01-01

Abstract:A kind of novel thin film of hybrid copper-cobalt hexacyanoferrate(CuCoHCF) on platinum substrate was prepared by cathodic deposition and this hybrid film was investigated as electrochemically controlled ion separation (ECIS) material for the selective,separation of alkali cations in aqueous nitrate solutions.In 0.1 mol/L KNO3solution,cyclic voltammetry(CV) and EQCMwere used to investigate the electroactivity and cycle life;in 0.1 mol/L(KNO3+CsNO3) mixture solution,CV was used to investigate the ion selectivity of the film.Experimental results show that CuCoHCF film is a substitution-type hexacyanoferrate,not the simple combination of single component of CuHCF and CoHCF.The films have good electroactivity and selectivity,and the cycle life of the films is better than that of the single component films,having preliminary characteristic of ECIS thin film.
Conjugated Polymers for Corrosion Control: Scanning Vibrating Electrode Studies of Polypyrrole-Aluminum Alloy Interactions

Jie He,Dennis E. Tallman,Gordon P. Bierwagen

DOI: https://doi.org/10.1149/1.1819632

IF: 3.9

2004-01-01

Journal of The Electrochemical Society

Abstract:The influence of electrodeposited polypyrrole (Ppy) films on the corrosion behavior of aluminum and Al 2024-T3 alloy, particularly on the corrosion behavior of exposed metal in damaged areas of the film, has been investigated using the scanning vibrating electrode technique (SVET). Two types of experiments are described. In one type, the Ppy was electrodeposited directly on the metal, a defect through the Ppy coating to the metal surface was introduced, and SVET measurements were made in and around the defect area. In the other type of experiment, the Ppy coating was electrodeposited on indium-tin oxide (ITO) conducting glass and electrical connection to the metal substrate was made through a switch. The SVET was then applied to map the current density distribution on both the Ppy-coated ITO and on the metal substrate when the switch was either closed or open. Both types of experiments demonstrate that the Ppy alters the corrosion behavior of the metal substrate, with dissolved oxygen playing a significant role. We also present data on the influence of oxygen on the open-circuit potential of the Ppy films and on the discharge behavior of such films. The implications of these results are discussed. © 2004 The Electrochemical Society. All rights reserved.

electrochemistry,materials science, coatings & films
A Facile Electrochemical Strategy for Achieving a High-Conductivity Polypyrrole Derivative with Intrinsic Metallic Transport as a High-Performance Electrochromic Conducting Polymer Film

Di Gao,Siming Zhao,Ya Huang,Xueke Wu,Run Li,Yilin Ding,Qinyuan Jiang,Yanlong Zhao,Fei Wang,Rufan Zhang

DOI: https://doi.org/10.1021/acs.nanolett.4c04570

IF: 10.8

2024-11-06

Nano Letters

Abstract:Conjugated polymer electrochromic materials (PECMs) with tailored optical and electrical properties are applied in smart windows, electronic displays, and adaptive camouflage. The limitation in the electrical conductivity results in slow and monotonous color switching. We present a polypyrrole film incorporated with a toluene-p-sulfonic group (PPy-TSO-F), via a one-step electrodeposition technique. The PPy-TSO-F thin film (110 nm) achieves an impressive electrical conductivity of 1011 S cm^(-1),...

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Preparation, Characterization and Anion Exchange Properties of Polypyrrole/Carbon Nanotube Nanocomposites

Xiaoli Cui,Mark H Engelhard,Yuehe Lin

DOI: https://doi.org/10.1166/jnn.2006.122

2006-01-01

Journal of Nanoscience and Nanotechnology

Abstract:In this study, polypyrrole (PPy) thin films were electrodeposited on carbon nanotube (CNT) backbones by applying a constant deposition potential in 0.1 M pyrrole solution with different electrolytes, such as NaCl, NaNO3, or NaClO4. The hybrid films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy, and cyclic voltammetry. SEM images revealed the nanostructrure of PPy films generated on CNT surface. The electrochemical and anion exchange properties of the PPy-CNT composite films have been investigated. Nanostructured composite thin films of PPy-CNTs were studied by cyclic voltammetry between 0.4 and -0.8 V in aqueous solution to evaluate their cycling stability and capacity for electrically switched anion exchange. The presence of the CNT backbone greatly improved the anion exchange capacity and stability of the PPy-CNT composite film, which may be attributed to the high surface area of CNT matrix, nanostructure of the PPy film, and the interaction between CNTs and PPy.
Electromagnetic composite films based on polypyrrole hydro-sponge and Fe3O4 ferrofluid

Li Fang,Tingyang Dai,Yun Lu

DOI: https://doi.org/10.1016/j.synthmet.2009.07.043

IF: 4

2009-01-01

Synthetic Metals

Abstract:The preparation of free-standing electromagnetic composite films based on conductive polypyrrole (PPy) hydro-sponge and the Fe3O4 ferrofluid have been successfully accomplished via self-assembly in the presence of β-cyclodextrin sulfate and under static condition. Transmission electron microscope (TEM), scanning electron microscope (SEM) and X-ray diffraction (XRD) are used to study the morphology of the PPy-Fe3O4 composite. Structural characterizations by Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) have proved the interactions between Fe3O4 and PPy chains. As-prepared films possess high electrical conductivity, remarkable magnetic response as well as appropriate flexility. Both the conductivity and magnetization of the composite, the latter in particular, depend strongly on the Fe3O4 content and thus can be optimized by adjusting the relative content of Fe3O4 in the composite. The combination of both magnetic and conducting activities of the resulting composite makes it be a potential candidate as functional material in electromagnetic devices, such as magnetic-controlled switches.
Fabrication of Graphene-cuprous Oxide Hybrid Paste Electrodes for Capillary Electrophoretic Measurement of Polyhydroxy Compounds

Farui Li,Kunming Jiang,Qianyu Wu,Zhenjie Li,Gang Chen

DOI: https://doi.org/10.1002/elan.202200183

IF: 3.077

2022-01-01

Electroanalysis

Abstract:An alkaline mixture containing copper(II) spices, graphene oxide and glucose was heated by far infrared radiations to synthesize graphene-cuprous oxide hybrid. The hybrid was blended with mineral oil and packed into tubes to fabricate paste electrodes. The electrodes were coupled with capillary electrophoresis for the detection of polyhydroxy compounds. The sensitivities of them on the hybrid electrodes were significantly enhanced by taking advantages of graphene and cuprous oxide. The contents of polyhydroxy compounds in tobacco method was determined by the electrodes with satisfactory assay results.
Solid State Electrochemical Properties of Electroactive Solutes in Polyurethane Ionomer Media

HS Xu,JJ Zhu,H Cheng,CZ Yang

DOI: https://doi.org/10.1002/pssa.2211560108

1996-01-01

Abstract:Cyclic voltammetry of ferrocene in polyethylene oxide polyurethane ionomer films was measured with microdisk electrodes at different temperatures. The cyclic voltammetric curve showed stability and reiteration. The electrode reaction of CpFeCp in polyurethane ionomer media is irreversible. The potential of the cathodic peak does not shift significantly with temperature within the range fi om room temperature to 70 degrees C. The peak current values increase with increasing measurement temperature. The temperature dependence of the ferrocene diffusion coefficient is a straight line compared with that of ionic conductivity. In comparing the changes of peak currents and conductivity, it was found that the tendency is analogous, but the shape of the two curves is quite different. The two mechanisms exhibit distinctive activation energies. The method of solid state voltammetric measurement with microdisk Electrodes has potential use in studying the conduction mechanism of polymer electrolytes.
Sers Study of the High Quality Conducting Polythiophene Film

JB He,HJ Zhou,F Wan,Y Lu,G Xue

DOI: https://doi.org/10.1016/s0924-2031(03)00015-8

IF: 2.5

2003-01-01

Vibrational Spectroscopy

Abstract:Surface enhanced Raman scattering (SERS) technique was used to monitor and analyze the electrochemically polymerized polythiophene (PT) layer on several metal electrodes, such as stainless steel and aluminum, during the different reaction stage. The SERS spectra were directly achieved from the PT films after silvering. The result of spectral measurement indicated that in the films formed at the initial moment of electropolymerization the thiophene rings in polymer chains have an ordered arrangement in the form of an alternate-layer parallel.
Probing Trace Pb2+ Using Electrodeposited N,N′-(o-phenylene)-bis-benzenesulfonamide Polymer As a Novel Selective Ion Capturing Film

Lei Zhang,Wei Li,Mianhong Shi,Jilie Kong

DOI: https://doi.org/10.1016/j.talanta.2006.02.070

IF: 6.1

2006-01-01

Talanta

Abstract:A novel film modified electrode for the determination of trace lead was developed in this work. The modified electrode was prepared by the electropolymerization of N,N′-(o-phenylene)-bis-benzenesulfonamide (PBSA) as the ion capturing reagent to create the functional film. The modified electrode shows a high selectivity towards Pb2+ over interfering cations, e.g. Cu2+, Cd2+, Co2+, Ni2+, Zn2+, Cr2+, and the calibration curve was linear in the concentration range of 2.0 × 10−9 to 1.0 × 10−7 M with correlation coefficient of 0.999. For 20 min accumulation, detection limit of 1.0 × 10−9 M was obtained at the signal to noise ratio of 3. Analytical availability of the modified electrode was demonstrated by the application for samples from pond water.
Investigation on the Electro-optic Properties and the Relaxation of Electric Poled Dye Doped Polymer Films

Zhiling Xu,Liying Liu,Xiu Liu,Zhanjia Hou,Lei Xu,Wencheng Wang,Mingxin Ye

DOI: https://doi.org/10.3321/j.issn:0258-7025.2000.08.017

2000-01-01

Abstract:Elliptical reflection method was used to measure the electro-optic coefficient of doped α′-cyano-4′-nitro-4-N, N-dimethylstibene (CNDS)/PMMA films. The decay of electro-optic signal of the CNDS/PMMA films with an coated Al electrode was measured in situ. A slow relaxation process was observed in the first few hours of the decay.
Selective determination of cuprous ion in copper dissolving solution based on bathocuproine-modified expanded graphite electrode

Xiaohui Chen,Yufa Sun,Wenchang Wang,Zhidong Chen,Zhiyao Ming

DOI: https://doi.org/10.1007/s44211-023-00358-w

Abstract:The presence of cuprous ions in the copper-dissolving solution significantly affects the microstructure of copper plated surface. Fewer quantitative analyses of cuprous ions in the copper foil productive process had rarely been involved so far. In the present work, a novel electrochemical sensor of the bathocuproine (BCP) modified expanded graphite (EG) electrode was developed for the selective determination of cuprous ions. EG has a large surface area, good adsorption, and excellent electrochemical performance which remarkably promoted analytical sensitivity. Meanwhile, the selective determination of the BCP-EG electrode for cuprous ions in the coexistence of ten thousand times of copper ions have been achieved on the benefit of the special coordination of BCP to cuprous ions. In the coexistence of 50 g/L copper ions, the analytical performance of the BCP-EG electrode for the determination of cuprous ions had been examined. The results represented a wide detection range of cuprous ions in the range of 1.0 μg/L-5.0 mg/L, with a low detection limit of 0.18 μg/L (S/N = 3) and the BCP-EG electrode has great selectivity to cuprous ions in presence of various interferences. The analytical selectively for cuprous ions supported by the proposed electrode would be a potential analytical tool for quality improvement in electrolytic copper foil manufacturing.

Probe beam deflection study of cupric hexacyanoferrate colloid doped polypyrrole film modified electrode in different electrolytes

Probe Beam Deflection Study of the Ion Exchange Between Prussian Blue Film or Indium Hexacyanoferrate Film and Electrolyte Solutions

Probing the Electrolyte Transfer in Ultrathin Polypyrrole Films by In Situ X-ray Reflectivity and Electrochemistry

Probe Beam Deflection study of Au Nanoparticles Supported into TiO2 Mesoporous Films

Electrochemical Study of a Polypyrrole Film/Decanethiol Self-Assembled Monolayer on a Gold Electrode

In Situ Preparation and Determination of Electrochemical and Electrochromic Properties of Copper Phthalocyanine-Polyaniline Nanocomposite Films

Colloidal processing of ferroelectric poly(vinylidene fluoride-co-hexafluoropropylene)—ferrimagnetic pseudocapacitive CuFe2O4 composite films

Electrochemical Performance of Electroactive Poly(Amic Acid)-Cu2+ Composites

Investigations of electrochemical polymerization processes of thin poly(pyrrole) films and its application to anion sensor based on surface plasmon resonance

Preparation, Characterization and Electrochemical Properties of Polypyrrole-Polystyrene Sulfonic Acid Composite Film

Preparation and Electrochemical Property of Copper Cobalt Hexacyanoferrate Hybrid Film

Conjugated Polymers for Corrosion Control: Scanning Vibrating Electrode Studies of Polypyrrole-Aluminum Alloy Interactions

A Facile Electrochemical Strategy for Achieving a High-Conductivity Polypyrrole Derivative with Intrinsic Metallic Transport as a High-Performance Electrochromic Conducting Polymer Film

Preparation, Characterization and Anion Exchange Properties of Polypyrrole/Carbon Nanotube Nanocomposites

Electromagnetic composite films based on polypyrrole hydro-sponge and Fe3O4 ferrofluid

Fabrication of Graphene-cuprous Oxide Hybrid Paste Electrodes for Capillary Electrophoretic Measurement of Polyhydroxy Compounds

Solid State Electrochemical Properties of Electroactive Solutes in Polyurethane Ionomer Media

Sers Study of the High Quality Conducting Polythiophene Film

Probing Trace Pb2+ Using Electrodeposited N,N′-(o-phenylene)-bis-benzenesulfonamide Polymer As a Novel Selective Ion Capturing Film

Investigation on the Electro-optic Properties and the Relaxation of Electric Poled Dye Doped Polymer Films

Selective determination of cuprous ion in copper dissolving solution based on bathocuproine-modified expanded graphite electrode