Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Molecular dynamics simulation on glass transition temperature of NR/CIIR/TPI polymer blend

Molecular Dynamics Simulation on the Glass Transition Temperatures of TPI/NR/LDPE

Molecular Simulation of the Glass Transition Temperature for Guatta-Percha

Molecular dynamics simulation of compatibility and mechanical properties for NR/CIIR/TPI blends

A Monte Carlo Study Of The Glass Transition Of Polymethylene

Molecular Dynamics Simulation of the Mechanical Properties of NR/TPI

Molecular Dynamics and Dissipative Particle Dynamics Simulation of TPI/NR Blends

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Polymer Structures and Glass Transition: A Molecular Dynamics Simulation Study

MD Simulation Study on the Compatibility of TPI/NR/LDPE Blends

Influence of Carbon Nanotube Aspect Ratio on Glass Transition Temperature of Polymers: A Molecular Dynamics Simulation Study

The abnormal behavior of polymers glass transition temperature increase and its mechanism

Study of glass transition temperature (Tg) of novel stress-sensitive composites using molecular dynamic simulation

Molecular Dynamic Simulation Study on Glass Transition Temperature of DGEBA-THPA/SWCNTs Composites

Molecular dynamics simulation of glass transition and thermal stability of novel silicone elastomer and its nanocomposites

Molecular Dynamic and Dissipative Particle Dynamic Simulation on the Miscibility of NR/CR Blends

Experimental Study of the Synergistic Plasticizing Effect of Carbon Dioxide and Ibuprofen on the Glass Transition Temperature of Poly(methyl Methacrylate)

Confined Crystallization in Polymer Blends: DSC Studies of the Behavior and Kinetics of Isothermal Crystallization of Polypropylene in Poly(cis-butadiene) Rubber Blends

Quantification of interfacial structure at nanoscale and its relationship with viscoelastic glass transition of SiO2/elastomer nanocomposites

Dependences of Confining Size and Interfacial Curvature on the Glass Transition of Polydimethylsiloxane in Self‐Assembled Block Copolymers

Molecular-weight and cooling-rate dependence of polymer thermodynamics in molecular dynamics simulation