Design of MAC buffer storage based on UWB

Chen Ze,Fu Zhongqian,Huang Lu

DOI: https://doi.org/10.3969/j.issn.1674-7720.2013.13.009

2013-01-01

Abstract:This paper implements a MAC cache design of IRUWB high-speed and short-range wireless communication network engineering. SDRAM makes data interface with the highest priority FIFO in MAC chip. This design finishes tapeout in SMIC 0.18 μm CMOS process. Chip test shows that it works well under 125 MHz.

What problem does this paper attempt to address?

Performance of Intra-Chip Wireless Interconnect Using On-Chip Antennas and UWB Radios

Mei Sun,Yue Ping Zhang,Guo Xin Zheng,Wen-Yan Yin

DOI: https://doi.org/10.1109/tap.2009.2024458

IF: 5.7

2009-01-01

IEEE Transactions on Antennas and Propagation

Abstract:An intra-chip wireless interconnect system using on-chip antennas and ultrawideband (UWB) radios that operates in 22-29 GHz is studied in this paper. The on-chip antennas are meander monopoles of axial length 1 mm in silicon technology. A unique wireless channel is formed between a pair of on-chip transmit and receive antennas. The channel is characterized up to an interconnect distance of 40 mm. The system performance is evaluated in terms of bit-error-rate (BER) under the assumptions of perfect system synchronization and signal corruption from thermal and switching noises. As expected, the system performance degrades with interconnect distance and data rate. It achieves a better BER on the 5-k¿.cm Si substrate than that on the 10-¿.cm Si substrate.
A 2-Gb/s/pin Source Synchronous CDMA Bus Interface with Simultaneous Multi-Chip Access and Reconfigurable I/O Capability

J Kim,ZW Xu,MF Chang

DOI: https://doi.org/10.1109/cicc.2003.1249411

2003-01-01

Abstract:A simultaneous reconfigurable multi-chip access bus interface for application in high-bandwidth multi-drop parallel interconnections such as a memory bus has been developed. The interface utilizes a source synchronous signaling and direct-sequence code-division multiple access (CDMA) technique for high bus concurrency and low channel latency. The prototype chip, fabricated in 0.18-/spl mu/m CMOS and tested in a 10-cm test board achieves a data rate of 2 Gb/s/pin with multiple access and re-configurability between four (2-to-2) off-chip I/Os.
A hybrid reservation-based MAC protocol for underwater acoustic sensor networks

Guangyu Fan,Huifang Chen,Lei Xie,Kuang Wang

DOI: https://doi.org/10.1016/j.adhoc.2013.01.002

IF: 4.816

2013-01-01

Ad Hoc Networks

Abstract:Due to the characteristics of underwater acoustic channel, such as long propagation delay and low available bandwidth, media access control (MAC) protocol designed for the underwater acoustic sensor network (UWASN) is quite different from that for the terrestrial wireless sensor network. However, for the contention-based MAC protocols, the packet transmission time is long because of the long preamble in real acoustic modems, which increase the packet collisions. And the competition phase lasts for long time when many nodes are competing for the channel to access. For the schedule-based MAC protocols, the delay is too long, especially in a UWASN with low traffic load. In order to resolve these problems, a hybrid reservation-based MAC (HRMAC) protocol is proposed for UWASNs in this paper. In the proposed HRMAC protocol, the nodes reserve the channel by declaring and spectrum spreading technology is used to reduce the collision of the control packets. Many nodes with data packets to be transmitted can reserve the channel simultaneously, and nodes with reserved channel transmit their data in a given order. The performance analysis shows that the proposed HRMAC protocol can improve the channel efficiency greatly. Simulation results also show that the proposed HRMAC protocol achieves better performance, namely higher network throughput, lower packet drop ratio, smaller end-to-end delay, less overhead of control packets and lower energy overhead, compared to existing typical MAC protocols for the UWASNs.
Research on the Application Solution for Data Buffer in MIMO Experimental Systems

Zishu He

2005-01-01

Abstract:The wireless communication system is up against various engineering challenges. For both the transmitted and the received data processing, fast-access memories with large capacity are required in experimentation systems with Multiple-Input Multiple-Output technique. SDRAM is a kind of random access memory with large-capacity and high-speed, but many Microprogrammed Control Units or normal Digital Signal Processors cannot directly interface with SDRAM due to the differences between control signals. Based on FPGA(field programmable gate array), a design method of SDRAM controller with USB interface to computer is proposed . Large-capacity data access is implemented at high speed by the controller circuit, which is working effectively in our MIMO experimentation system.
A MAC for IR-UWB networks with receiver controlled handshake

PENG Bing-guang,WEI Guo,ZHU Jin-kang

DOI: https://doi.org/10.3969/j.issn.0253-2778.2007.09.017

2007-01-01

Journal of University of Science and Technology of China

Abstract:An IR-UWB system communicates by transmitting very narrow pulses.Without use of carrier modulation,MAC protocol based on carrier sensing can not be applied to IR-UWB system.Through analyzing the cause of RTS/CTS handshake failure of UWB MACAW MAC,UWB-RI MAC with receiver controlled handshake was proposed.In UWB-RI MAC,the receiver sends FI frame to indicate that it is free to receive RTS,and then the sender transmits RTS to start RTS/CTS handshake.Based on detailed working process of UWB-RI MAC,FI frame broadcast interval was analyzed and the support for QoS was explained.Finally,the performance simulation and comparison of UWB-RI MAC and UWB MACAW MAC were given.
Flexible Platform Design of IEEE 802.15.3a MAC over UWB with Optimized Protocol Accelerator

Y Cai,YH Wu,H Li,L Feng,ZC Zhou

DOI: https://doi.org/10.1109/icasic.2005.1611292

2005-01-01

Abstract:IEEE 802.15.3a is assumed to be candidate MAC protocol for emerging UWB techniques. To make MAC system flexible, configurable and easy to upgrade, we tried to make most of MAC functionalities as software/firmware process running in CPU for controlling UWB network card and maintaining high-data-rate WPAN network. But 480Mbps data rate requires some MAC functionality to respond in several microseconds and it is beyond the capability of current software without any hardware preprocessing. After carefully analyzing the bottleneck of timing requirements, we put forward an optimized MAC hardware protocol accelerator and integrated it in our flexible HW/SW system. Performance analysis shows that the throughput, delay etc. were greatly improved
Design of Compatibility Interleaver in Ultra Wide Band Wireless Communication System

LI Chen-xi,LIU Liang,YE Fan

DOI: https://doi.org/10.3969/j.issn.1000.3842.2011.11.089

2011-01-01

Abstract:This paper designs a interleaver which is used in Ultra Wide Band(UWB) system.The interleaver is based on the structure of two port Random Access Memory(RAM) and address generator,it can be compatible with standards of Multi Band-Orthogonal Frequency Division Multiplexing(MB-OFDM) and Dual Carrier-Orthogonal Frequency Division Multiplexing(DC-OFDM).To compare with the interleaver applied to only one standard,this interleaver just increase 4.5% and the registers increase 1.8%.The main clock frequency is 132 MHz and the max throughput is 1.42 Gb/s,and it meets the requirement of UWB system.
Design and implementation of high speed convolution decoder for UWB

Jin Yingguang,Pei Yukui,Ge Ning,Wang Youzheng

2009-01-01

JOURNAL OF ELECTRONIC MEASUREMENT AND INSTRUMENT

Abstract:Chip design of convolution decoder for ultra-wide band(UWB) system is involved with two challenges-high speed and low power consumption.Based on the analysis of different algorithms and structures of viterbi decoding,an architecture of parallel trace-back decoder suitable for ASIC implementation is proposed.At the cost of 30%memory resource,this structure increases the number of the parallel trace-back branches,thus decreases frequency to half of the traditional one.Simulation and experiment results show that,without performance degradation,the speed of a single module is up to 220Mbps,while its delay is only 2.4μs,which adapts to burst mode with low delay.
Structure design of data buffer for high-speed exchange devices

Jie Wang,Zhenzhou Ji,MingZeng Hu

2006-01-01

WSEAS TRANSACTIONS ON COMPUTERS

Abstract:Along with the rapid increase of Internet bandwidth and the development of Internet applications, gigabit and ten-gigabit exchange devices are applied widely. The high performance structure of high-speed data buffer is a key to break throughput rate necklace. We provide a new design of multi-level buffer structure based on Field Programmable Gates Array (FPGA) by internal RAMs combined with external RAMs. Corresponding parallel schedule algorithm increases transmission speed and process ability. By improving pipeline, this structure can be applied for more high-speed environments.
A resource preserved MAC protocol for QoS provided UWB ad hoc networks

Jiachen Zhou,Yiqing Huang,Takeshi Ikenaga

2008-01-01

Abstract:This paper proposes a resource preserved medium access control (MAC) protocol which provides Quality of Service (QoS) support for multimedia applications in ultra-wideband (UWB) ad hoc network. The proposed protocol accounts for the UWB unique characteristics while considering the QoS requirements. The evaluation results in throughputs, end to end delay, power consumption and power utilization show that, the proposed algorithms achieve a balance work between the throughputs and power consumption.
Study on the Low Power Cache Design Technique

郑伟,姚庆栋,张明,刘鹏,张子男,周莉,李东晓

DOI: https://doi.org/10.3969/j.issn.1007-0249.2004.05.006

2004-01-01

Abstract:Reduction of the power consumption of microprocessors has now become one of the most critical design concerns. On-chip cache memories dominate the chip area and the power consumption in microprocessor chips. This paper describes an architectural design technique, using Read/Write buffers to reduce the on-chip cache memories accesses activity, hence significantly reduce the power consumption of the whole chip because of the low power consumption characteristic of buffer compared with cache. In MD32 design, this technique normally reduces instruction cache access or data cache access by 20~40% showed by the simulation results of multimedia test benches.
An MBOK-UWB SoC Transceiver in 0.181&#x03bc;m CMOS Technology

Sheng Zhang,Jianliang Zhang,Mengmeng Liu,Shuo Wang,Heng Liang,Zhou Runde

DOI: https://doi.org/10.1109/icasic.2007.4415759

2007-01-01

Abstract:A system-on-a-chip (SoC) pulse-based MBOK-UWB transceiver for high-speed wireless transmission is presented in this paper. The system achieves the data rate of 100 Mbps. The digital baseband implements RAKE receiving architecture, with M-ary bi-orthogonal keying (MB OK) spread spectrum modulation, low-density parity-check (LDPC) error-correct coding and Ethernet interface. The front-end circuits include low-power pulse generator, 3~5GHz wideband low-noise amplifier (LNA) and 1 Gsps 4 bit flash analog-to-digital converter (ADC). These modules of proposed SoC has been designed and fabricated in HJTC 0.18 mum 1P6M CMOS technology. The baseband had been designed and implemented in one Xilinx FPGA.
Design of Low Power and High Speed FFT/IFFT Processor for UWB System

刘亮,王雪静,叶凡,仁俊彦

DOI: https://doi.org/10.3321/j.issn:1000-436x.2008.09.006

2008-01-01

Abstract:A new 128/64-point FFT/IFFT processor used in Ultra-Wide-Band(UWB) system was presented.The proces-sor,which is based on 8×8×2 mixed radix algorithm,can deal with multiple inputs more efficiently for MIMO applica-tions.A new eight-path-feedback structure,which can provide a higher throughput and lower power dissipation,was proposed.The test chip has been fabricated using SMIC 0.13μm single-poly and eight-metal CMOS process with a core area of 1.44mm2.The throughput of this chip is up to 1Gsample/s,and the power dissipation is 39.6mW when it works at the throughput of 500Msample/s which meets the UWB standard.This chip reduces 40% of core area and saves 45% of power dissipation compared with those existing 128-point FFT processors.
MAC: a novel systematically multilevel cache replacement policy for PCM memory

Shenchen Ruan,Haixia Wang,Dongsheng Wang

DOI: https://doi.org/10.48550/arXiv.1606.03248

2016-06-10

Hardware Architecture

Abstract:The rapid development of multi-core system and increase of data-intensive application in recent years call for larger main memory. Traditional DRAM memory can increase its capacity by reducing the feature size of storage cell. Now further scaling of DRAM faces great challenge, and the frequent refresh operations of DRAM can bring a lot of energy consumption. As an emerging technology, Phase Change Memory (PCM) is promising to be used as main memory. It draws wide attention due to the advantages of low power consumption, high density and nonvolatility, while it incurs finite endurance and relatively long write latency. To handle the problem of write, optimizing the cache replacement policy to protect dirty cache block is an efficient way. In this paper, we construct a systematically multilevel structure, and based on it propose a novel cache replacement policy called MAC. MAC can effectively reduce write traffic to PCM memory with low hardware overhead. We conduct simulation experiments on GEM5 to evaluate the performances of MAC and other related works. The results show that MAC performs best in reducing the amount of writes (averagely 25.12%) without increasing the program execution time.
Design of A Digital Baseband Processor for Uwb Transceiver on Rfid Tag

Yuechao Niu,Majid Baghaei Nejad,Hannu Tenhunen,Li-Rong Zheng

DOI: https://doi.org/10.1109/ainaw.2007.147

2007-01-01

Abstract:In this paper we present a novel digital baseband processor designed for UWB transceiver on RFID tag. It is a low power and low voltage (1.8V) full digital ASIC which is implemented in 0.18 mu m CMOS technology. The processor receives serial signals (consist of data and commands) from the RF Receiver, and based on received command carries out various functions such as receive data and write to the memory, compare data, send data, set/reset tag, kill tag and etc. The processor mainly consists of eight sub modules: Receive Buffer, Transmit Buffer, Random Number Generator (RNG), Slot Counter, Memory Controller, Reset Counter, Comparator, Controller.
Affinity-aware DMA Buffer Management for Reducing Off-Chip Memory Access

Qi Zhong,Xuetao Guan,Tao Huang,Xu Cheng,Keyi Wang

DOI: https://doi.org/10.1145/2245276.2232031

2012-01-01

Abstract:It is well recognized that moving I/O data in/out memory has become critical for high bandwidth devices. Specifically, the embedded system, with limited cache size and simple architecture, consumes a large amount of CPU cycles for off-chip memory access. The work presented in this paper addresses this problem through an A ffinity-aware D MA B uffer management strategy, called ADB, requiring no change to underlying hardware. We introduce the concept of buffer affinity describes the data location of the recently released DMA buffer in the memory hierarchy. The more data in cache, the higher affinity the buffer has. Based on the character of the embedded system, we can identify buffer affinity at runtime. Using this online profiling, ADB allocates buffer with different affinity. For output processes, ADB allocates the high affinity buffer to reduce off-chip memory access when OS copies data from the user buffer to the kernel buffer. For input processes, ADB allocates the low affinity buffer to skip part of cache invalidation operations for maintaining I/O coherence. Measurements show that ADB, implemented in the Linux-2.6.32 kernel and running on a 1GHz UniCore-2 processor, improves the performance of network related programs from 5.2% to 8.8%.
Banshee: Bandwidth-Efficient DRAM Caching Via Software/Hardware Cooperation

Xiangyao Yu,Christopher J. Hughes,Nadathur Satish,Onur Mutlu,Srinivas Devadas

DOI: https://doi.org/10.48550/arXiv.1704.02677

2017-04-10

Hardware Architecture

Abstract:Putting the DRAM on the same package with a processor enables several times higher memory bandwidth than conventional off-package DRAM. Yet, the latency of in-package DRAM is not appreciably lower than that of off-package DRAM. A promising use of in-package DRAM is as a large cache. Unfortunately, most previous DRAM cache designs mainly optimize for hit latency and do not consider off-chip bandwidth efficiency as a first-class design constraint. Hence, as we show in this paper, these designs are suboptimal for use with in-package DRAM. We propose a new DRAM cache design, Banshee, that optimizes for both in- and off-package DRAM bandwidth efficiency without degrading access latency. The key ideas are to eliminate the in-package DRAM bandwidth overheads due to costly tag accesses through virtual memory mechanism and to incorporate a bandwidth-aware frequency-based replacement policy that is biased to reduce unnecessary traffic to off-package DRAM. Our extensive evaluation shows that Banshee provides significant performance improvement and traffic reduction over state-of-the-art latency-optimized DRAM cache designs.
Co-design of ESD Protection and UWB RF Front-End ICs

Xin Wang,He Tang,Lin,Jian Liu,Qiang Fang,Hui Zhao,Albert Wang,ZiTao Shi,SiQiang Fan,Bin Zhao,LiWu Yang,Jun He,YuHua Cheng

DOI: https://doi.org/10.1007/s11432-011-4416-3

2011-01-01

Science China Information Sciences

Abstract:This paper discusses critical aspects for co-design of ultra wideband (UWB) system-on-chip (SoC) and on-chip electrostatic discharge (ESD) protection, which are beyond the considerations on data rate and bandwidth. Impulse radio UWB system architecture has been defined with critical building blocks proposed and verified, including pulse generator, transmitter, low noise amplifier (LNA) and multiplier based correlator. ESD protection is well considered for each related block. Design examples have been implemented in a commercial RFCMOS processes to demonstrate the working principles for key UWB transmitter and receiver circuit blocks. UWB-ESD co-design techniques, simulation and measurement results for these UWB RF modules are presented in detail.
Design of a Rake receiver for high speed single carrier ultra-wideband systems

Geng Chunhua,Pei Yukui,Ge Ning,Wen Wujie

DOI: https://doi.org/10.3772/j.issn.1002-0470.2010.09.013

2010-01-01

Abstract:A two-stage digital Rake receiver design is presented for direct-sequence spreading based single carrier ultra-wideband (SC-UWB) systems in scenarios of long channel delay spread. In this design, two stages of shift registers and two stages of multiplexers are employed for multipath separation. Compared with the conventional design, the proposed scheme obtains the same performance but reduces the hardware resource consumption significantly and avoids muting congestion in high speed UWB systems, so it is suitable for implementation of the Rake receiver using FPGA and ASIC. Moreover, the presented Rake receiver can change the selection of multipath components flexibly to track the timing jitter in transmission. The layout of the UWB receiver based on the SMIC 0.18μm CMOS technology is also given.
A high efficiency robust IR-UWB receiver design for high data rate CM-range communications

Dang Liu,Shuli Geng,Woogeun Rhee,Zhihua Wang

DOI: https://doi.org/10.1109/ISCAS.2014.6865531

2014-01-01

Circuits and Systems

Abstract:This paper describes circuit techniques for robust IR-UWB receiver design for high data rate centimeter range communications. For high data rate transmission, multiple frequency bands are utilized to increase transmission power for improved link margin, in the receiver design, a multiband LNA, a fully differential squarer, and a high speed parallel interlacing integrator are developed for high speed data recovery without requiring a high performance analog-to-digital converter. In this work, a 500Mb/s 12.5mW UWB receiver is designed in 65nm CMOS, achieving energy efficiency of 25pJ/b. Simulation results show that narrowband interference from the frequency band of 802.11a wireless standard whose power spectral density is 70dB higher than target sensitivity of -65dBm can be tolerated.

Design of MAC buffer storage based on UWB

Performance of Intra-Chip Wireless Interconnect Using On-Chip Antennas and UWB Radios

A 2-Gb/s/pin Source Synchronous CDMA Bus Interface with Simultaneous Multi-Chip Access and Reconfigurable I/O Capability

A hybrid reservation-based MAC protocol for underwater acoustic sensor networks

Research on the Application Solution for Data Buffer in MIMO Experimental Systems

A MAC for IR-UWB networks with receiver controlled handshake

Flexible Platform Design of IEEE 802.15.3a MAC over UWB with Optimized Protocol Accelerator

Design of Compatibility Interleaver in Ultra Wide Band Wireless Communication System

Design and implementation of high speed convolution decoder for UWB

Structure design of data buffer for high-speed exchange devices

A resource preserved MAC protocol for QoS provided UWB ad hoc networks

Study on the Low Power Cache Design Technique

An MBOK-UWB SoC Transceiver in 0.181&amp;#x03bc;m CMOS Technology

Design of Low Power and High Speed FFT/IFFT Processor for UWB System

MAC: a novel systematically multilevel cache replacement policy for PCM memory

Design of A Digital Baseband Processor for Uwb Transceiver on Rfid Tag

Affinity-aware DMA Buffer Management for Reducing Off-Chip Memory Access

Banshee: Bandwidth-Efficient DRAM Caching Via Software/Hardware Cooperation

Co-design of ESD Protection and UWB RF Front-End ICs

Design of a Rake receiver for high speed single carrier ultra-wideband systems

A high efficiency robust IR-UWB receiver design for high data rate CM-range communications

An MBOK-UWB SoC Transceiver in 0.181μm CMOS Technology