Abstract:Purpose: To evaluate the shear bond strength (SBS) of resin composite to dentin contaminated with artificial saliva (AS) containing mucin and amylase using an experimental method controlling the volume of saliva and adhesive in a defined surface area. Methods: Flat bonding surfaces were prepared on extracted human molars (320 grit surface). Using adhesive tape, a 4.5 mm bonding window was prepared on the dentin surfaces. Groups (n= 12) were prepared using the etch & rinse (ER) or self-etch (SE) modes for Adhese Universal (ADH), Scotchbond Universal Plus (SBU), and Prime & Bond active (PBA) dental adhesives (DA). For the control (C) groups, the adhesives were applied per the manufacturers' instructions with 2.0 µl or 3.0 µl of the adhesive. For the saliva-contaminated groups, 1.0 µl of artificial saliva with mucin was applied in the bonding window either dried or allowed to remain wet before the application of either 2.0 µl or 3.0 µl of the adhesive. After the adhesive film was air dried and light cured using an Ultradent bonding fixture, Spectrum TPH3 was bonded to the prepared surfaces. After water storage for 24 hours at 37°C, the specimens were debonded and shear bond strength (SBS) was calculated (MPa). A Kruskal-Wallis test with Bonferroni correction was used to determine group differences (P< 0.05). Scanning electron microscopy (SEM) was performed to visualize the interfacial surfaces prepared using an ion-etching technique. Results: Mean SBS for the three adhesives were similar in both ER and SE modes to uncontaminated dentin surfaces for all the control groups. For dentin contaminated with dried or wet saliva, both the surface condition and the adhesive system were significant factors at a confidence level of 95%. For the dried saliva test groups, ADH and PBA with 3.0 µl of adhesive generated similar SBS values to controls while SBU generated lower values. Lower values were generated when using 2.0 µl of adhesive for the three adhesives in SE and ER modes except for PBA in the ER mode. Using wet saliva and 3.0 µl of adhesive ADH and SBU generated lower SBS values while PBA generated similar values to controls. Under SEM, morphology at the adhesive dentin interfaces was similar among the adhesives to uncontaminated dentin but notable differences were observed for SBU and ADH for both wet and dried saliva-contaminated surfaces. Clinical significance: Salivary contamination differentially affects shear bond strength and the morphology of the bonded interface of universal adhesives to dentin. These differences are specific to the adhesive tested and are influenced by using the etch and rinse or self-etch strategies and the volume of adhesive used. When concerned about salivary contamination clinically, maximizing the volume of adhesive on the substrate may help mitigate the deleterious effects of saliva contamination.

Effect of Saliva Contamination and Decontamination on Bovine Enamel Bond Strength of Four Self-Etching Adhesives.

Effects of Saliva Contamination on Bonding Performance of Self-Etching Adhesives

Effect of Saliva on the Tensile Bond Strength of Different Generation Adhesive Systems: An In-Vitro Study

Effects of salivary contamination on the shear bond strengths of universal adhesives to dentin

Influence of saliva contamination on the shear bond strength of orthodontic brackets bonded with self-etching adhesive systems

Bonding Quality of Etch-and-Rinse Adhesives in Root Canals Upon Different Pretreatments.

Influence of Surface Pretreatment on the Bond Strength of a Resin Luting Cement to Saliva-contaminated Enamel and Dentin

[Effects of Three Self-Etch Adhesives and Mild Salivary Contamination on the Bonding Durability of Deciduous Teeth].

[Effects of Saliva Contamination on Bond Strength of Resin-Resin Interfaces].

Effects of Dentine Surface Cleaning on Bonding of a Self-Etch Adhesive to Root Canal Sealer-Contaminated Dentine.

Bonding Effectiveness of Saliva-Contaminated Monolithic Zirconia Ceramics Using Different Decontamination Protocols

A scoping review of the influence of clinical contaminants on bond strength in direct adhesive restorative procedures

Influence of Priming Time and Primer'S Concentrations on Bovine Enamel Bond Strengths

Bonding Protocols to Reverse the Bond Strength of a Universal Adhesive to Hemostatic Agent-contaminated Dentin

SEALING OF BONDED RESIN COMPOSITE TO GINGIVAL WALL FOLLOWING APPLICATION OF TWO HEMOSTATIC AGENTS USING TWO ADHESIVE PROTOCOLS: AN INVITRO STUDY

Effectiveness of different cleaning measures on the bonding of resin cement to saliva-contaminated or blood-contaminated zirconia

A Study to Evaluate the Effect of Cleaning Solutions on Shear Bond Strength of Resin Cement to Saliva-Contaminated Lithium Disilicate (LDS) Ceramic

Enamel deproteinization before acid etching and its effect on the shear bond strength--an in vitro study

Antibacterial Activity and Bonding Ability of an Orthodontic Adhesive Containing the Antibacterial Monomer 2-Methacryloxylethyl Hexadecyl Methyl Ammonium Bromide.

Effect of Preventive Dental Products on Bonding Force: An in vitro Study

Prime-and-rinse Approach for Improving the Enamel Micro-Tensile Bond Strengths of Self-Etch Adhesives