Abstract:An SMA (shape memory alloy) is a functional material with a unique property known as the shape memory effect, or superelasticity. Microscopically, the mechanical actuation of this effect is based on reversible transformation between different crystal phases. To clarify the atomistic mechanism in SMA, we perform molecular dynamics simulation (MDS) of phase transformations for a Ni-Ti alloy, a typical alloy used for engineering SMAs. EAM potential, which can produce both B2 and B19' structures (stable crystal phases of Ni-Ti), is adopted to model the interatomic interaction of the nickel and titanium atomic systems. Two different-sized MDS models are constructed with unit cell structures of B2 phase. These structures are surrounded by free surfaces and constrained regions so as to be subjected to uniaxial tensile loading. A series of reversible processes likely to occur in SMA, including loading, unloading, heating, and cooling, is reproduced by corresponding stages of the MDS. Phase transformation is thought to be observable by detecting the local interatomic distances and bonding angles peculiar to B19' structure (martensite). During tensile loading simulations, the martensite crystal structure is always observed, having transformed from the B2 structure. At a large strain, models exhibit a rapid propagation of local lattice distortions accompanied by the formation of martensite. In unloading simulations, the larger model contains relatively less martensite than the smaller model. The discrepancy with regards to model size may depend on a different degree of constraint strength. Reverse transformation (from B19' to B2) occurs mainly in the subsequent heating stage, in which the stress is observed to increase under constant residual strain.

Microstructure and Phase Transformation Characteristics of Ni3Ta Alloy

An in Situ TEM Study of the Size Effect on the Thermally Induced Martensitic Transformation in Nanoscale NiTi Shape Memory Alloy

Microstructure and phase transformation of TiNi alloy with addition of third element Sn

Effects of Heat Treatment on the Transformation Temperature and the Microstructure of Ni-Ti-Nb Shape Memory Alloy

Recent Electron Microscopy Results on Micro- and Nanostructured Ni-Ti-(X) Shape Memory Alloys

In-Situ High-Energy Synchrotron X-Ray Diffraction Study of Micromechanical Behavior of Multiple Phases in Ni47ti44nb9 Shape Memory Alloy

Microstructure, Phase Transformation and Mechanical Property of Nb-doped Ni–Mn–Ga Alloys

Microstructural Evolution in NiTi Alloy Subjected to Surface Mechanical Attrition Treatment and Mechanism

Microstructural features, martensitic transformation, and functional properties of multicomponent Ti–Ni based shape memory alloys

Effect of Ta on Microstructures and Mechanical Properties of NiTi Alloys

Experimental Observations on Mechanical Response of Three-Phase Niti Shape Memory Alloy under Uniaxial Tension

Observation of Phase Transformation and Structural Analysis for Ni-Ti Alloy by Molecular Dynamics Simulation

Microstructure and Thermoelastic Martensitic Transformation in Ni-Low and -Rich Ni–Ti–Hf–Nb Hightemperature Shape Memory Alloys

Metastable transformation behavior in a Ta-containing TiAl-Nb alloy during continuous cooling

Microstructure Evolution and Phase Transformations in Ti-22Al-25Nb Alloys Tailored by Super-Transus Solution Treatment

Microstructure Transformation of a Refined High Nb Containing TiAl Alloy

Phase Transformation And Microstructure Of Nbru High Temperature Shape Memory Alloy

The α 2 to orthorhombic O-phase transformation-facilitated high elastically mediated strain transfer ability in high Nb-TiAl alloys

Regularities in the Evolution of Thermoelastic Martensitic Transformations during Cooling/Heating in the Free State and under Load of Titanium Nickelide Alloyed with Niobium

Optimization of Ta Content of a Third Generation Ni3Al Base Single Crystal Superalloy

Microstructure and properties of intermetallic compounds of W/Ni/Ta diffusion couple