Abstract:Sn-Sb alloys are potential solders for replacement of high-Pb solders because of their high melting temperature in lead-free solders. However, Cu substrate is extremely dissolved by the Sn-Sb binary alloy during the high temperature soldering process, which will cause serious reliability problem of the solder joint. Based on this critical issue, we designed a new high temperature lead-free Sn-10Sn-5Cu ternary solder to prevent the dissolution of Cu substrate. In this study, liquid-state interfacial reaction between the high temperature lead-free solder and the Cu substrate was investigated. The liquid-state interfacial reaction of the solder on the Cu substrate was carried out at the different temperature of 280degC, 320degC,360degC and 400degC, and the reaction time was 1min, 10mins, 30mins and 60mins, respectively. Microstructure of the Sn-Sb-Cu bulk solder and the solder joint was observed by scattered electron microscope (SEM). The identification of phase composition was determined by Energy Dispersive X-ray Detector (EDX) and electron probe microscopy analysis (EPMA). During the four reaction temperatures, the interfacial reaction products included a scallop Cu6Sn5 intermetallic compound (IMC) layer and a flat Cu3Sn layer adjacent to Cu substrate. IMCs thickness with the reaction time was measured by the area of interface IMCs layer divided by the interface length. The IMCs thickness increased with the reaction temperature and reaction time, and the relationship between IMC thickness and reaction time was linear with square root of time, which signified that the IMC growth dynamics was diffusion controlled. The diffusion coefficient was calculated by the IMC growth rate, which increased with the higher temperature, corresponding to be 2.30 times 10-14, 6.84 times 10-14, 1.63 times 10-13, 1.99 times 10-13 m2/s for the temperatures of 280degC, 320degC, 360degC and 400degC, res- - pectively. And then the diffusion activation energy was determined to be 57.8 KJ/mol by fitting the four diffusion coefficients at various temperatures, which indicated that the diffusion mechanism was grain boundary diffusion. Between lower temperature of 280degC and higher temperature of 400degC, huge differences existed on the microstructure of IMC in the interior solder of the solder joint.

Effect of Oxide Thickness of Solder Powders on the Coalescence of Snagcu Lead-Free Solder Pastes

Effects of High-Temperature Treatment on the Reaction Between Sn-3%Ag-0.5%Cu Solder and Sputtered Ni-V Film on Ferrite Substrate

Influences of Tin Oxide Surface Modification on the Morphology and Performance of Sintered Ag/SnO2 Composite Powders

Effect of the impurity in electroless plated Powders on morphology and properties of sintered AgSnO2 materials

The influences of Ag nanoparticles on voids growth and solderability about Sn3.0Ag0.5Cu/Cu solder joint

Influence of Al2O3 Nanoparticles on the Morphology and Growth Kinetics of Cu-Sn Intermetallic Compounds in Sn-Ag-Zn/Cu Solder Joints

Solder paste metamorphism

Liquid-state interfacial reaction of Sn-10Sb-5Cu high temperature lead-free solder and Cu substrate

The impact of paste alloy, paste volume, and surface finish on solder joint

Effects of Alloying Elements on the Characteristics of Sn-Zn Lead-Free Solder

Relationship between the Reduction Behavior of Copper and Tin Oxide Films by Formic acid and Solder Wettability

Understanding the corrosion protection effect by surface oxide film to underlying Sn solder substrate under thermal exposure condition

Effect of foam porosity on microstructure and grain refinement by using composite solder

High-temperature aging time-induced composition and thickness evolution in the native oxides film on Sn solder substrate

Wettability of Sn-Bi and Sn-Ag-Cu Lead-Free Solder Pastes on Electroplated Co-P Films

Effect of the addition of CeO 2 nanoparticles on the microstructure and shear properties of Sn-57Bi-1Ag solder alloy

The effect of chemical species in the lead frame materials on the interface microstructure between copper alloys and SnPb solder

Origin of Primary Cu6Sn5 in Hypoeutectic Solder Alloys and a Method of Suppression to Improve Mechanical Properties

Effects of ZrO2 Nano-Particles' Incorporation into SnAgCu Solder Alloys: An Experimental and Theoretical Study

Effect of electromigration on microstructure and properties of CeO2 nanopartical-reinforced Sn58Bi/Cu solder joints

Effects of initial Cu grain size and impurity residues on the liquid phase reactions between molten solder and electroplated Cu