Abstract:Quality assurance of adhesively bonded joints is of vital importance if their benefits are to be exploited across a wide range of industrial applications. A novel lightweight, low-cost, non-invasive embedded sacrificial sensor is proposed, capable of detecting damage within an adhesively bonded joint, which could also be used in a laminated composite structure. The sensor operation uses changes in electrical resistance, increasing as the sensing material area diminishes with damage progression. Initial tests prove the sensor concept by showing that the electrical resistance of the sensor increases proportionally with material removal, mimicking the sensor operation. Thermography is used to verify the current flow through the sensor and that any localised heating caused by the sensor is minimal. Short beam interlaminar shear strength (ILSS) tests show that embedding sensors in a composite laminates did not cause a reduction in material interfacial structural performance. Finally, the in situ performance of the sensor is demonstrated in quasi-static tensile tests to failure of adhesively bonded single lap joints (SLJs) with sensors embedded in the bond line. Prior to crack initiation, an electrical response occurs that correlates with increasing applied load, suggesting scope for secondary uses of the sensor for load monitoring and cycle counting. Crack initiation is accompanied by a rapid increase in electrical resistance, providing an indication of failure ahead of crack propagation and an opportunity for timely repair. As the crack damage propagated, the electrical response of the sensor increased proportionally. The effect of the sensor on the overall structural performance was assessed by comparing the failure load of joints with and without the embedded sensor with no measurable difference in ultimate strength. The research presented in the article serves as an important first step in developing a simple yet promising new technology for structural health monitoring with numerous potential applications.

Debonding Detection Using A Self-Calibration Sensor Network

A Fiber Optic Doppler Sensor and Its Application in Debonding Detection for Composite Structures.

Debonding detection for CFRP structures using fiber optic Doppler sensors

A Novel Method of Embedding Distributed Optical Fiber Sensors for Structural Health Monitoring

Interfacial Debonding Detection for Steel-Concrete Composite Structures Part I: Benchmark Test and Signal Calibration of Contact and Non-Contact Measurement

Development of an integrated sacrificial sensor for damage detection and monitoring in composite materials and adhesively bonded joints

Debonding Detection of Reinforced Concrete (RC) Beam with Near-Surface Mounted (NSM) Pre-stressed Carbon Fiber Reinforced Polymer (CFRP) Plates Using Embedded Piezoceramic Smart Aggregates (SAs)

In Situ Disbond Detection in Adhesive Bonded Multi-Layer Metallic Joint Using Time-of-flight Variation of Guided Wave

NUMERICAL ANALYSIS AND EXPERIMENTAL RESEARCH FOR ACOUSTIC-OPTICAL FIBER BASED DETECTION OF INTERFACIAL DAMAGE IN FRP-RETROFITTED STRUCTURES

Interfacial Debonding Detection for Steel-Concrete Composite Structures Part II: Scanning Doppler Laser-Based MASW and Microphone Combination-Based Impact-Acoustic Vibration

Damage Detection of CFRP Bolted Joints Using Embedded Optical Fibers with BOCDA System

Delamination Detection in CFRP Laminates Using FOD Sensor

Detecting Debonding between Steel Beam and Reinforcing CFRP Plate Using Active Sensing with Removable PZT-Based Transducers

Non-destructive evaluation of smart materials by using extrinsic Fabry–Perot interferometric and fiber Bragg grating sensors

Adhesive Defect Monitoring of Glass Fiber Epoxy Plate Using an Impedance-Based Non-Destructive Testing Method for Multiple Structures

Acoustic Emission Based Monitoring of Fatigue Damage in CFRP-CFRP Adhesive Bonded Joints

Smart Adhesive Joint with High-Definition Fiber-Optic Sensing for Automotive Applications

Nondestructive Evaluation of Bond Quality of Adhesively Joined Carbon Fiber/nylon 6 Composites

The Health Monitoring of Bonded Composite Joints Using Both Thickness and Radial Impedance Resonance Responses

A Novel Embedded Fiber Optic Acoustic Emission Sensor and Its Applications for Monitoring Failures of Composite Laminates

Frp Debonding Monitoring Using Otdr Techniques