Abstract:The polyoxymethylene (POM) fiber was melt spun by use of different commercial grades of POM resin, and the effect of post-drawing on mechanical properties and microstructures was investigated extensively. The fiber obtained from the POM resin with a higher melt flow index (MFI) exhibits a better hot-drawing capability and also achieves a greater ultimate draw ratio. The mechanical evaluation reveals that the tensile strength and elastic modulus of POM fiber are improved significantly after post-drawing compared to the as-spun fibers. Although the greater draw ratios result in higher mechanical strength and modulus for the POM fiber, the fiber obtained from the POM resin with an MFI of 13.0 g/10 min achieves the optimal mechanical performance at the ultimate draw ratio. The morphologic and structural developments of POM fiber were studied by scanning electronic microscopy and X-ray powder diffraction. The results indicate that the POM fiber spun by the resin with an MFI of 13.0 g/10 min has a smooth lateral surface and a compact cross section after post-drawing. The fiber samples spun by the POM resins with low MFIs show some hollow disfigurements as well as a rough surface at the ultimate draw ratio, whereas the fiber obtained from the resin with a high MFI of 27.0 g/10 min presents the ununiformity of diameter after post-drawing. The POM fibers achieve a crystalline orientation during the hot-drawing process, which results in a transformation from the spherulitic crystals to the lamellar structure in the drawing direction. The level of crystalline orientation can be improved with an increase of draw ratio and thus results in a high modulus and strength for the resulting POM fiber samples. In addition, the thermal analysis indicates that the crystallinity of the as-spun fibers can be enhanced by post-drawing due to the orientation-induced crystallization.

Flow Properties and Extrudate Swell During Extrusion of Polyformaldehyde Melt

Study on the Viscosity of Polymer Polyol

Correlations between molecular weight, mechanical properties and morphology of micro-injection molded polyoxymethylene (POM)

The polymer melt swelling behavior in micro-extrusion process for preparation of continuous carbon fiber reinforced PP prepreg filament

Research on Flow Pattern and Molecular Mechanisms of Polymer Molten During Injection Filling Stage

RHEOLOGICAL PROPERTIES OF POLY(VINYLIDENE FLUORIDE) MELT

Poly(lactic Acid)/polyoxymethylene Blends: Morphology, Crystallization, Rheology, and Thermal Mechanical Properties

Effect of Flowing Preformed Spherulites on Shear-Induced Melt Crystallization Behaviors of Isotactic Polypropylene

Rheological Properties of Poly(Vinylidene Fluoride) in Molten State

Rheological properties of poly(trimethylene terephthalate) in capillary flow

Morphological Structure and Mechanical Properties of a Nucleated Polyoxymethylene (POM) Homopolymer Resin Processed Under Conventional Injection Molding Conditions

Preparation, mechanical properties and microstructure of polyoxymethylene fiber through melt spinning and hot drawing by using injection-molding grade resins

Miscibility and Double Glass Transition Temperature Depression of Poly(l-lactic Acid) (plla)/poly(oxymethylene) (POM) Blends

Physical and chemical effects of ultrasound vibration on polymer melt in extrusion

Rheological and extrusion behavior of intercalated high-impact polystyrene/organomontmorillonite nanocomposites

Microstructural Evolution and Its Effect on Mechanical Properties of Isotactic Polypropylene by Shear Plastic Deformation at Elevated Temperatures

Rheological Behavior of PP/PVAc-OMMT Nanocomposites

Influence of acrylonitrile styrene copolymer on the thermal stability of polyoxymethylene resin

Thermal and mechanical degradation during polymer extrusion processing

Numerical modelling of the viscoelastic polymer melt flow in material extrusion additive manufacturing

Overshoots in Stress and Free Energy Change During the Flow-Induced Crystallization of Polymeric Melt in Shear Flow