Abstract:Background: Temporomandibular joint (TMJ) overloading is considered a primary cause of temporomandibular joint disorders (TMD). Accordingly, craniomaxillofacial structural parameters affect the loading situation in the TMJ. However, no effective method exists for quantitatively measuring the loading variation in human TMJs. Clinical statistics, which draws from general rules from large amounts of clinical data, cannot entry for exploring the underlying biomechanical mechanism in craniomaxillofacial system. The finite element method (FEM) is an effective tool for analyze the stress and load on TMJs for several cases in a short period of time; however, it is difficult to generalize general patterns through calculations between different cases due to the different geometric characteristics and occlusal contacts between each case. Methods: (1) This study included 88 subjects with 176 unilateral data to measure angle (α) of the distance to the plane of occlusion. The bone destruction score was evaluated for clinical statistics. To rule out effects of the potential factors and ensure the generality of the study, one participant with no obvious bone destruction was selected as the standard case for establishing the three-dimensional (3D) theoretical model and FEM. (2) Three groups of forces, including biting, muscles and joint reaction forces on mandible, were adopted to establish a 3D theoretical model. (3) By modifying the sagittal α and coronal three types of deviation angle (φ) of the original model, nine candidate models were obtained for the FEM studies. Results: (1) The static equilibrium equations, were used to establish a 3D theoretical model for describing the loading of the TMJ. The theoretical model was validated by monotonously modifying the structural parameter in comparison to two-dimensional theoretical models reported previously; (2) The force on the TMJ gradually decreased with α, and this trend was validated by both clinic statistics and FEM results; (3) The effects of the three types of deviation angle were different. The results of the case where only rotating biting forces were considered was consistent with clinical statistics, indicating that the side with lower α experiences higher TMJ load. (4) Changing the unilateral proportionality coefficients of biting and muscle force produced opposite effects, wherein the effects of the muscle force were stronger than those of the biting forces. Conclusions: A negative correlation was observed between the joint load and α. Among the three types of asymmetric deformities, occlusal deviations were the primary factors leading to TMD. Unilateral occlusion can result in a greater load on the ipsilateral joint and should be avoided when using the side corresponding to the TMD. This study provides a theoretical basis for the biomechanical mechanism of TMD and also enables the targeted mitigation and treatment of TMD through structural modification.

Influence of teeth contact alternation to TMJ stress distribution ---- Three-dimensional finite element study

[Effect of Change in Occlusal Contact Areas of the Mandibular Second Molar on Temporomandibular Joint Stress Distribution: a 3-Dimensional Finite Element Analysis].

Analysis of the Influence of Lower Premolar Rotation on TMJ Stress Distribution by Finite Element Method

[A Three-Dimensional Finite Element Analysis on the Effect of Seven Different Occlusions on TMJ].

Variation in stress distribution modified by mandibular material property: a 3D finite element analysis

Biomechanical Simulation of the Interaction in the Temporomandibular Joint Within Dentate Mandible: A Finite Element Analysis

[Stress Analysis of the Mandible by 3D FEA in Normal Human Being under Three Loading Conditions].

[A Three-Dimensional Finite Element Study on the Reaction of Different Force Values Generated from Maxillary Protraction Appliance].

Three-dimensional finite element analysis on the effect of posterior cross-bite of individual teeth on temporomandibular joint]

Three-dimensional Finite Element Stress Analysis of the Temporomandibular Joint During Mandibular Osteodistraction

Three-dimensional Finite Element Study on Stress Distribution of Temporomandibular Joint in Patients with Close Anterior Deep Bite under Two Loading Conditions

Three-dimensional theoretical model for effectively describing the effect of craniomaxillofacial structural factors on loading situation in the temporomandibular joint

[Analysis of Human Mandible and Temporomandibular Joint Using Three-Dimensional Finite Element Method under Different Mechanical Models].

Three-dimensional finite element analysis of different reactive force direction of maxillary protraction on temporomandibular joint

Effects of Occlusal Loads on the Stress Distributions in Temporomandibular Joint

Effect of occlusal contact on TMJ loading during occlusion: An in silico study

Associations Between Condylar Height Relative to Occlusal Plane and Condylar Osseous Condition and TMJ Loading Based on 3D Measurements and Finite Element Analysis

Three-dimensional Finite Element Analysis of Traumatic Mechanism of Mandibular Symphyseal Fracture Combined with Bilateral Intracapsular Condylar Fractures

Condyle Bone Destruction: the Association Between Temporomandibular Joint Vibration and Finite Element Analysis

Effects Of Several Temporomandibular Disorders On The Stress Distributions Of Temporomandibular Joint: A Finite Element Analysis

Biological stress analysis of condylar transverse fracture and longitudinal fracture using three-dimensional finite element method