Abstract:With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.

PENETRATION CHARACTERISTICS OF W-Cu SHAPED CHARGE PARTICLES JET

Investigation on the anti-penetration performance of the steel/nylon sandwich plate

Experimental Study on Copper Powder Liner

Deep Penetration Mechanism of Jet Produced by Shaped Charge with Porous Liner at Low Standoff Distance

Effect of tungsten contents on the jet penetration performance of shaped charge liner based copper-tungsten composites

Smooth Particle Hydrodynamics-Based Characteristics of a Shaped Jet from Different Materials

Jet Formation and Penetration Performance of a Double-Layer Charge Liner with Chemically-Deposited Tungsten As the Inner Liner

The Penetration–Explosion Effects of Differently Distributed Inactive/Active Composite Shaped Charge Jets

The effect of three-layer liner on the jet formation and penetration capability of shaped charge jet

The Influence of Closed-Cell W-Shaped Liner Parameters on the Penetration Performance of Integral Annular Shaped Charge

Formation and Penetration Properties of a Shaped Charge with Zr41.2Ti13.8Cu12.5Ni10Be22.5 Liner

Density Effect of PTFE-Copper Powder Metallurgy Liner Material on the Perforation Performance of Shaped Charge Jets

Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner

Study on Penetration Behavior of the Reactive Material Composite Jet against Concrete

Investigation of Penetration Performance of Zr-based Amorphous Alloy Liner Compared with Copper

Study on Big Entry Hole Bidirectional Shaped Charge

Study on Forming Law and Penetration of a Spherical Cone Composite Structure Liner Based on the Explosion Pressure-Coupling Constraint Principle

Jet Penetration Performance of a Shaped Charge Liner Prepared by Metal Injection Molding

Influence of lead on the performance of powder shaped charge liner

Penetration and jet flame effects induced by the interaction between a new energetic penetrator and a simulated shielding charge

Penetration and Cratering of Steel Target by Jets from Titanium Alloy Shaped Charge Liners