Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

Finite element simulation and experiment of isothermal die forging process of TC18 Ti alloy disc

Optimization of hot deformation parameters for multi-directional forging of Ti65 alloy based on the integration of processing maps and finite element method

Finite element analysis of heavy forging processing with JTS method

Mechanical and Physical Characterizations of a Three-Phase TiAl Alloy during Near Isothermal Forging

Experiment Study on Friction Behaviour of Ti-6Al-4V Alloy for Hot-working

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Constitutive Relationship of Ti-1023 Alloy during Isothermal Forging Processes

Numerical simulation and experiment study on hot extrusion process of 18Ni (250) maraging steel large fan shaft for aero-engines

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

SIMULATION ANALYSIS OF WHEEL BEARING FORGING PROCESS BASED ON DEFORM

Optimization of multi-directional forging parameters of large-scale Mg-Gd-Y-Zn-Zr alloy forged part guided by finite element simulation

High Nb–TiAl Intermetallic Blades Fabricated by Isothermal Die Forging Process at Low Temperature

Transformation characteristics of temperature and phases within Ti-6Al-4V aeroengine drum in hot forging and air cooling procedures

Microstructure and Properties of Ti-23Al-17Nb Alloy Forging Disk

Investigation on the thermal deformation mechanisms and constitutive model of Ti-55511 titanium alloy

Investigation of hot deformation behavior and microstructure evolution of TC18 alloy and establishment of constitutive equation under friction-temperature correction

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Casting Design Optimization Using Numerical Simulation of Precision Forging Die for Large Titanium Alloy Integral Bulkhead

A New Method for Controlling Billet Temperature During Isothermal Die Forging of a Complex Superalloy Casing

Numerical Simulation and Experimental Verification of the Quenching Process for Ti Microalloying H13 Steel Used to Shield Machine Cutter Rings