Abstract:The morphology and content of the divorced eutectic in the microstructure of high pressure die casting (HPDC) magnesium alloy have a great influence on the final performance of castings. Based on the previous work concerning simulation of the nucleation and dendritic growth of primary α-Mg during the solidification of magnesium alloy under HPDC process, an extension was made to the formerly established CA (Cellular Automaton) model with the purpose of modeling the nucleation and growth of Mg-Al eutectic. With a temperature field and solute field obtained during simulation of the primary α-Mg dendrites as the initial condition of the modified CA model, modeling of the Mg-Al eutectic with a divorced morphology was achieved. Moreover, the simulated results were in accordance with the experimental ones regarding the distribution and content of the divorced eutectic. Taking a "cover-plate" die casting with AM60 magnesium alloy as an example, the rapid solidification with a high cooling rate at the surface layer of the casting led to a fine and uniform grain size of primary α-Mg, while the divorced eutectic at the grain boundary revealed a more dispersed and granular morphology. Islands of divorced eutectic were observed at the central region of the casting, due to the existence of ESCs (Externally Solidified Crystals) which contributed to a coarse and non-uniform grain size of primary α-Mg. The volume percentage of the eutectic β-Mg17Al12 phase is about 2%-6% in the die casting as a whole. The numerical model established in this study is of great significance to the study of the divorced eutectic in the microstructure of die cast magnesium alloy.

Microstructure Characteristics of the Eutectics of Die Cast AM60B Magnesium Alloy

Modeling Studies on Divorced Eutectic Formation of High Pressure Die Cast Magnesium Alloy

Effect of Solutionising and Ageing on the Microstructure and Mechanical Properties of a High Strength Die-Cast Al–Mg–Zn–Si Alloy

Weibull Statistical Analysis of the Effect of Melt Conditioning on the Mechanical Properties of AM60 Alloy

Melt Superheating on the Microstructure and Mechanical Properties of Diecast Al-Mg-Si-Mn Alloy

Investigation on Surface Defects Produced in Pretreatment of Die-casting AM60B Magnesium Alloy

Effects of Process Parameters on Morphology and Distribution of Externally Solidified Crystals in Microstructure of Magnesium Alloy Die Castings

Microstructure and Mechanical Properties of Magnesium Alloy AZ91D Produced by Rheo-Diecasting Process

Effect of Heat Treatment on Microstructures and Mechanical Properties of High Vacuum Die Casting Mg–8Gd–3Y–0.4Zr Magnesium Alloy

Microstructural Evolution of Vacuum Die-Cast AZ91D Magnesium Alloy During Solution Treatment

Analysis of microstructure of as-cast ZK60 magnesium alloy

Modeling of Microstructure Evolution of Magnesium Alloy During the High Pressure Die Casting Process

Microstructure and Mechanical Properties of Melt-Conditioned High-Pressure Die-Cast Mg-Al-Ca Alloy

Microstructure, Mechanical Properties and Die-Filling Behavior of High-Performance Die-Cast Al–Mg–Si–Mn Alloy

Characterization of the Grain Structures in Vacuum-Assist High-Pressure Die Casting AM60B Alloy

Effects Of Heat Treatment On Microstructure And Mechanical Properties Of Die-Cast Mg-8gd-3y-0.5zr Magnesium Alloy

Effect of Alloying with Al, Nd and Ca and Heat Treatment on Microstructures and Mechanical Properties of Vacuum Die-Cast AM50 Alloy

Microstructure and Mechanical Properties of Sand Mold Cast Mg–4.58Zn–2.6Gd–0.18Zr Magnesium Alloy after Different Heat Treatments

Formation Mechanism of the Microstructural Heterogeneity in a Die-Cast Al-Mg-Si Alloy and Its Effect on Mechanical Properties

On the Deformation Behavior of Heterogeneous Microstructure and Its Effect on the Mechanical Properties of Die Cast AZ91D Magnesium Alloy

Effect of Different Casting Techniques on the Microstructure and Mechanical Properties of AE44-2 Magnesium Alloy