Abstract:Aim: (1) To compare the temperature rise in the pulp chamber with different resin materials used for making provisional fixed partial dentures in anterior and posterior region while using Polyvinylsiloxane impression materials as matrix. (2) To identify a superior provisionalization material based on the amount of heat dissipated suitable for anterior and posterior provisional fixed partial denture fabrication. Settings and design: Temporary crowns and bridges are integral to Fixed Prosthodontics. It has been observed that conventional fixed prosthesis temporisation materials release heat due to the exothermic polymerisation reaction. When such a provisional material is directly let to set on a vital tooth, the heat transfer causes irreversible changes in the pulp tissue depending of the degree of change. Hence, this study observes amount of heat generation in various materials during temporisation procedure, by simulating similar conditions. Materials and methods: Two Models were fabricated, one simulating missing lateral incisor (Model A) and another simulating missing first molar (Model B). Intact maxillary central incisors and canine for Model A and intact mandibular Second Premolar and Second Molar were selected to act as abutments. These abutment teeth were fitted with the tip of a K-type Thermocouple inside their pulp chambers and these were connected to a digital thermometer. Five temporisation materials were chosen for fabrication of temporary crowns through Direct technique. (1) polymethy methacrylate (Self Cure acrylic), (2) bisacryl composite (Protemp 4), (3) visible light cure urethane dimethacrylate (Revotec LC), (4) barium glass and fumed silica infused methacrylate (Dentsply Integrity) and (5)nano-hybrid composite (VOCO Structur 3). Ten observations were made for each provisional material on each model. During each observation, temperature rise was recorded at 30s interval from the time of application, through the peak and till a decrease in temperature is observed. Polyvinyl siloxane was used as matrix for all except light cure resin, where polypropylene sheet was used. Statistical analysis used: Anova test used for statistical. Results: ANOVA test revealed that there was a significant difference in the temperature changes associated with the provisional restorative materials used. Among the five, polymethy methacrylate (self cure resin) showed the maximum rise in temperature, followed by bisacryl composite (Protemp 4), visible light cure urethane dimethacrylate (Revotec LC), barium glass and fumed silica infused methacrylate (Dentsply Integrity) and nano-hybrid composite (VOCO Structur 3). There was no comparable difference between Model A and B but an overall reduction of temperature rise was observed in model B. Conclusion: VOCO Structur 3 showed the least temperature rise in the pulp chamber, and overall temperature rise was less for model B which can be attributed to the residual dentin thickness.

The study of the monomer release from four kinds of temporary crown material by infrared spectrum]

The Expression of PCNA and Bcl-2 in Gingival Tissue after the Restoration of Four Types of Temporary Crowns

Effects of monomer released from temporary crowns on DNA damage of buccal mucosa epithelial cells

An animal experiment study on apo ptosis increase of buccal mucosa cells induced by residual monomer released from temporary crown materials

Monomer Elution of Additive and Subtractive Manufactured Resins for Permanent Restorations

Monomer Release from Dental Resins: The Current Status on Study Setup, Detection and Quantification for In Vitro Testing

Peri-implant Marginal Bone Changes with Implant-Supported Metal-Ceramic or Monolithic Zirconia Single Crowns: A Retrospective Clinical Study of 1 to 5 Years.

Evaluation of Monomer Releasing from Dentin Replacement Materials

Comparison of water absorption, solubility and monomer release of six kinds of light-curing composite resins

Evaluation of the amount of residual monomer released from different flowable composite resins

An In Vitro Scanning Electronic Microscope Evaluation

Comparison of the flexural strength and marginal accuracy of traditional and CAD/CAM interim materials before and after thermal cycling.

Combinatorial investigation of structure–properties relationships and microcosmic curing mechanism of dental adhesives functional monomers

A comparative study of marginal microleakage and bond strength using three kinds of cements in zirconia all ceramic crown

In Vitro Marginal Adaptation of Single Crowns Fabricated from Several Provisional Resins

A comparative in vitro analysis of various temporization materials with respect to pulp chamber temperature changes during polymerization

[Influence of Different Resin Bond Systems on Coronal Microleakage of Fiber Posts and Core Restorations].

Elemental analysis and micromorphological patterns of tooth/restoration interface of three ion-releasing class V restorations

Adhesive Interfacial Characteristics and the Related Bonding Performance of Four Self-Etching Adhesives with Different Functional Monomers Applied to Dentin.

Influence of surface treatment of yttrium-stabilized tetragonal zirconium oxides and cement type on crown retention after artificial aging

Influence of provisional cementation on the stability of adhesively bonded resin-based composite crowns