Abstract:In vivo magnetic resonance image (MRI)-based computational models have been introduced to calculate atherosclerotic plaque stress and strain conditions for possible rupture predictions. However, patient-specific vessel material properties are lacking in those models, which affects the accuracy of their stress/strain predictions. A noninvasive approach of combining in vivo Cine MRI, multicontrast 3D MRI, and computational modeling was introduced to quantify patient-specific carotid artery material properties and the circumferential shrinkage rate between vessel in vivo and zero-pressure geometries. In vivo Cine and 3D multicontrast MRI carotid plaque data were acquired from 12 patients after informed consent. For each patient, one nearly-circular slice and an iterative procedure were used to quantify parameter values in the modified Mooney-Rivlin model for the vessel and the vessel circumferential shrinkage rate. A sample artery slice with and without a lipid core and three material parameter sets representing stiff, median, and soft materials from our patient data were used to demonstrate the effect of material stiffness and circumferential shrinkage process on stress/strain predictions. Parameter values of the Mooney-Rivlin models for the 12 patients were quantified. The effective Young's modulus (YM, unit: kPa) values varied from 137 (soft), 431 (median), to 1435 (stiff), and corresponding circumferential shrinkages were 32%, 12.6%, and 6%, respectively. Using the sample slice without the lipid core, the maximum plaque stress values (unit: kPa) from the soft and median materials were 153.3 and 96.2, which are 67.7% and 5% higher than that (91.4) from the stiff material, while the maximum plaque strain values from the soft and median materials were 0.71 and 0.293, which are about 700% and 230% higher than that (0.089) from the stiff material, respectively. Without circumferential shrinkages, the maximum plaque stress values (unit: kPa) from the soft, median, and stiff models were inflated to 330.7, 159.2, and 103.6, which were 116%, 65%, and 13% higher than those from models with proper shrinkage. The effective Young's modulus from the 12 human carotid arteries studied varied from 137 kPa to 1435 kPa. The vessel circumferential shrinkage to the zero-pressure condition varied from 6% to 32%. The inclusion of proper shrinkage in models based on in vivo geometry is necessary to avoid over-estimating the stresses and strains by up 100%. Material stiffness had a greater impact on strain (up to 700%) than on stress (up to 70%) predictions. Accurate patient-specific material properties and circumferential shrinkage could considerably improve the accuracy of in vivo MRI-based computational stress/strain predictions.

2D and 3d Multi-Physics Models for Flow and Nonlinear Stress/Strain Analysis of Stenotic Arteries with Lipid Cores

Quantifying Effects Of Controlling Factors On Flow And Stress Distribution In Stenotic Arteries With Lipid Cores

Mri-Based Flow And Stress Analysis Of Human Arterial Plaques With Lipid Cores And Calcifications

Effect of a lipid pool on stress/strain distributions in stenotic arteries: 3-D fluid-structure interactions (FSI) models.

3D MRI-Based Multicomponent FSI Models for Atherosclerotic Plaques

3D Computational Mechanical Analysis for Human Atherosclerotic Plaques Using MRI-Based Models with Fluid-Structure Interactions

3D Mri-Based Anisotropic Fsi Models with Cyclic Bending for Human Coronary Atherosclerotic Plaque Mechanical Analysis

In Vivo/Ex Vivo Mri-Based 3d Non-Newtonian Fsi Models For Human Atherosclerotic Plaques Compared With Fluid/Wall-Only Models

Sensitivity analysis of 3D MRI-based models with fluid-structure interactions for human atherosclerotic coronary and carotid plaques

A 3-D Thin-Wall Model with Fluid–structure Interactions for Blood Flow in Carotid Arteries with Symmetric and Asymmetric Stenoses

Wall Stress And Strain Analysis Using A Three-Dimensional Thick-Wall Model With Fluid-Structure Interactions For Blood Flow In Carotid Arteries With Stenoses

3D in Vivo Ivus-Based Anisotropic Fsi Models with Cyclic Bending for Human Coronary Atherosclerotic Plaque Mechanical Analysis

Using in Vivo Cine and 3D Multi-Contrast MRI to Determine Human Atherosclerotic Carotid Artery Material Properties and Circumferential Shrinkage Rate and Their Impact on Stress/strain Predictions.

3-D Simulation for Blood Flow and Artery Compression in Asymmetric Stenotic Arteries with Axial Stretch

Quantifying vessel material properties using mri under pressure condition and mri-based fsi mechanical analysis for human atherosclerotic plaques

Sensitivity Analysis Of 3d Mri-Based Models For Atherosclerotic Plaques

Patient-specific artery shrinkage and 3D zero-stress state in multi-component 3D FSI models for carotid atherosclerotic plaques based on in vivo MRI data.

In Vivo IVUS-Based 3-D Fluid–Structure Interaction Models with Cyclic Bending and Anisotropic Vessel Properties for Human Atherosclerotic Coronary Plaque Mechanical Analysis

Quantifying effects of plaque structure and material properties on stress distributions in human atherosclerotic plaques using 3D FSI models.

Steady flow and wall compression in stenotic arteries: a three-dimensional thick-wall model with fluid-wall interactions.

Simulating cyclic artery compression using a 3D unsteady model with fluid–structure interactions