Abstract:PURPOSE The clinical failures of zirconia dental restorations are often caused by extrinsic artifacts introduced by processing. The aim of this study was to investigate the micro-defects and residual stresses generated during the multistep process of zirconia dental restorations. MATERIALS AND METHODS Thermal spray granulated 3Y-TZP powders were dry pressed by two tools exhibiting distinctly different Young's moduli, cold isostatic pressed (CIP-ed), and pressure-less fully sintered. The green bodies pressed by a stiff tool were treated with different procedures: direct milling (green milling) followed by fully sintering; half-sintering and milling (raw milling) with or without fully sintering; and fully sintering followed by grinding. The fully sintered 3Y-TZP crowns were clinically adjusted using both a diamond bur and SiC bur, respectively. Phase composition and microstructure of the pressed, milled, and ground surfaces were studied by XRD and SEM. RESULTS Tetragonal phase was the main phase of all detected 3Y-TZP specimens. Excessive residual stresses introduced by raw milling and grinding were confirmed by a strained T (111) peak, monoclinic phase, and obviously changed I(002)t /I(200)t ratio. The residual stresses would form a compressive stress layer, while it was too shallow to inhibit crack propagation even for ground specimens. Large voids with high-coordination numbers were the common packing micro-defects. Once formed, they were barely healed by CIP-ing and sintering. A stiff pressing tool was confirmed to be useful for reducing the surface packing voids. Milling removed the surface voids, but was no help for the interior ones. Raw milling introduced more serious chippings, most originating from the existing packing voids, than green milling due to its brittle failure and was less recommended for production. Grinding dense 3Y-TZP caused surface grain refinement and much more severe micro-defects, especially when clinical adjustment was applied by diamond bur compared to SiC bur. CONCLUSIONS Micro-defects and residual stresses are introduced and accumulated through the entire production chain and determine the final microstructure of zirconia dental restorations. Several procedural improvements are offered and expected to reduce processing micro-defects.

The structure and property of nano-zirconia ceramic prepared by aqueous electrophoretic deposition on gypsum material

Fabrication of In-Ceram Dental Restoration by Aqueous Electrophoretic Deposition

Accuracy and Margin Quality of Advanced 3D-Printed Monolithic Zirconia Crowns.

The characteristic and osteogenic effect of a nanoporous coating of zirconia implant

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Fabrication of Zirconia Ceramic Dental Crowns by Digital Light Processing: Effects of the Process on Physical Properties and Microstructure

Preparation and Properties of Dental Zirconia Ceramics

Conventional sintering of nano-crystalline Yttria-Stabilized Zirconia enables high-strength, highly translucent and opalescent dental ceramics

Fabrication of translucent graded dental crown using zirconia-yttrium multi-slurry tape casting 3D printer

Manufacturing and Characterization of Dental Crowns Made of 5-mol% Yttria Stabilized Zirconia by Digital Light Processing

High-performance integrated manufacturing of a 3Y-TZP ceramic crown through viscoelastic paste-based vat photopolymerization with a conformal contactless support

Digital light printing of zirconia/resin composite material with biomimetic graded design for dental application

Effects of glass-ceramic spray deposition manipulation on the surface characteristics of zirconia dental restorations

Fabrication of enamel-like structure on polymer-infiltrated zirconia ceramics

Fabrication and characterization of bioactive zirconia-based nanocrystalline glass-ceramics for dental abutment

Rapid-Sintered Dental Zirconia For Chair-Side One-Visit Application

The Effect of Nano-Silica Surface Infiltration on Bond Strength of a Phosphate-Monomer-containing Composite Cement to Zirconia.

Improved performance of diatomite-based dental nanocomposite ceramics using layer-by-layer assembly.

Strength and Adaptation of Stereolithography-Fabricated Zirconia Dental Crowns: an in Vitro Study

Evaluation of the Feasibility of NaCaPO4-Blended Zirconia as a New CAD/CAM Material for Dental Restoration

Effect of Multistep Processing Technique on the Formation of Micro-Defects and Residual Stresses in Zirconia Dental Restorations.