Dielectric properties of honey adulterated with sucrose syrup
Wenchuan Guo,Yi Liu,Xinhua Zhu,Shaojin Wang
DOI: https://doi.org/10.1016/j.jfoodeng.2011.06.013
IF: 6.203
2011-01-01
Journal of Food Engineering
Abstract:Sucrose syrup is a common additive in honey adulteration. To provide information for developing a cheap, simple, convenient and rapid sucrose–adulterated honey detector or sucrose content sensor, the permittivities of pure jujube, yellow-locust and milk-vetch flower honey, pure sucrose syrup and honey–sucrose syrup mixtures with sucrose content from 0% (pure honey) to 80% (pure sucrose syrup) were studied from 10 to 4500 MHz with open-ended coaxial-line technology and a network analyzer at room temperature. The correlations between permittivities and sucrose contents were regressed. The results showed that the dielectric constants of all samples decreased with increasing frequency, while the pure honey had higher dielectric constant than pure sucrose syrup. Dielectric relaxation existed in all samples. The maximum loss factor decreased with increasing sucrose content. The relaxation frequency changed very little with sucrose content. Strong negative linear correlation, R 2 > 0.98, was found between loss factor around the relaxation frequency and sucrose content. Keywords Honey Adulteration Sucrose syrup Sucrose content Permittivity Dielectric constant Dielectric loss factor 1 Introduction Honey is the only naturally sweet product produced by bees using the nectar of plants or honeydew. According to International regulations ( Codex Alimentarius Commission, 2001 ) and Chinese standards ( GB18796-2005, 2005 ) for honey, the honey sold as such shall not have added to it any food ingredient, including food additives, nor shall any other additions be made other than honey. Unfortunately, for economic gain, honey adulteration is a major problem in the world. Honey contains more than 180 constituents ( Al et al., 2009 ). The main compositions are fructose and glucose, followed by water, sucrose, minerals, vitamins, proteins and amino acids, etc. ( Wang, 2007 ). Although the amount of each ingredient varies with bee species, floral sources, geographical origins and climatic conditions ( Perez-Arquillue et al., 1994 ), it is stipulated that the content of fructose and glucose together in honey should be not less than 60 g/100 g (60% in mass ratio), and sucrose content should be not more than 5% on mass basis ( Codex Alimentarius Commission, 2001; GB18796-2005, 2005 ). Contrasted with fructose and glucose, sucrose produced from vegetables is much cheaper. Therefore, sucrose syrups of natural origin such as maple, cane sugar, beet sugar, etc., are common sweetener additives in honey for increasing total sugar content. In many countries, such as China, the great majority of honey is collected by honey processing factories from beekeepers, then packed and marketed. A minority of honey is sold by beekeepers themselves. Hand-held refractometer is usually used to check sugar content in honey. But it just provides total soluble solid content. Moreover, sucrose–adulterated honey cannot be identified easily by visually examining or tasting. Therefore, not only beekeepers, but also some honey packers or processing factories, produce sucrose–adulterated honey. High performance liquid chromatography (HPLC) is required to measure sucrose content in honey ( GB/T-18932.22-2003, 2003 ). Besides HPLC method, isotope ratio mass spectrometry, anthrone spectrophotometer, silver nitrate and α-naphthol methods are also used to determine sucrose content in honey ( Bogdanov and Martin, 2002; Wang, 2003 ). However, expensive instruments, complicated procedures, long processing time and/or high operation ability requirement for users make these analytical methods be impractical in the field and market. Although technologies, developed based on food stuffs’ physical properties, such as acoustic, optical, magnetic, mechanical, thermal and fluid properties, have been explored in detecting food qualities, each technique has its application field. Dielectric properties of food materials reflect the storage and dissipation of electromagnetic energy. This technology is not only unlimited to food varieties, but also simple, rapid, non-destructive and sensitive ( Lizhi et al., 2010 ). Therefore, a lot of efforts were made to study dielectric properties in detecting food qualities and adultery. Many researches have shown that the dielectric properties are influenced by food compositions, such as moisture content, ash content, salt content and fat content, etc. ( Içier and Baysal, 2004; Ng et al., 2008; Ryynänen, 1995; Sosa-Morales et al., 2010 ). Based on the dielectric spectroscopy difference, dielectric properties have been used to detect olive oil adulterated with vegetable oils ( Lizhi et al., 2010 ), poultry meat, pork products and fish added with water, etc. ( Kent and Anderson, 1996; Kent et al., 2001, 2002 ). Several studies also revealed moisture content in honey samples have significant effects on honey dielectric properties ( Guo et al., 2010; Puranik et al., 1991 ). There was strong positive linear relationship between dielectric constant and moisture content in honey ( Guo et al. 2010 ). Dielectric properties could be used to detect honey adulterated with water. Ahmed et al. (2007) noticed that dielectric properties of honey were affected by ash content. However, there is lack of the knowledge about the effect of sucrose content on honey permittivity in radio and microwave frequencies. So the objective of the present study was to measure permittivities of honey samples added with sucrose syrup from 10 to 4500 MHz, and to establish correlations between the permittivities and sucrose content in honey. The results from this study will provide information for developing an affordable, dielectric property-based sensor to rapidly predict sucrose–adulterated honey or sucrose content in honey. 2 Materials and methods 2.1 Honey and sucrose Jujube honey, yellow-locust honey and milk-vetch honey of Chinese floral sources of Chinese jujube ( Ziziphus jujub e), yellow-locust tree ( Robinia pseudoacacia L. ) and Chinese milk-vetch ( Astragalus sinicus Linn. ), respectively, were used in the study. The honey was collected from beekeepers and packed by Shaanxi Dangdai Honey Industry Co., Ltd. in May, 2010. No crystal was observed in used samples. The total sugar, sucrose, moisture and ash contents of the samples used are listed in Table 1 . The methods that were used to obtain these contents are described in the following sections. The moisture contents of these samples were below 18%, which is the maximum moisture content allowed by Chinese national regulations for honey ( GB18796-2005, 2005 ), and complied with the Codex Alimentarius Standard, which stipulates that honey should have a maximum moisture content of 20% ( Codex Alimentarius Commission, 2001 ). The total sugar contents were 79.8%, 80.3% and 80.8% in jujube, yellow-locust, and milk-vetch honey, respectively. Sucrose (analytical reagent), met the standard of HG/T3462-1999 (1999) and produced by Tianjin Bodi Chemical Holding Co., Ltd. (Tianjing, China), was used for preparing sucrose syrup. 2.2 Dielectric properties measurement The dielectric properties are commonly represented by the relative complex permittivity ε ∗ = ε ′ - j ε ″ , where the real part ε ′ is dielectric constant, and the imaginary part ε ″ is dielectric loss factor ( Guo et al., 2008, 2010 ). Dielectric properties of samples were measured according to the procedure described in our previous study ( Guo et al., 2010 ) over spectral frequency range from 10 to 4500 MHz using an Agilent Technologies vector network analyzer (E5071C), Agilent Technologies open-ended coaxial-line probe (85070B) and dielectric probe kit software (85070D, Agilent Technologies, Penang, Malaysia). The dielectric constant and loss factor were calculated according to the reflection coefficient of the material in contact with the active tip of the probe. Total 101 measurements were conducted on a logarithmic scale between 10 and 4500 MHz. Before calibrating the coaxial probe with open (air), short circuit and deionized water at 25 °C, the port of the network analyzer used in the experiment was calibrated with open, short, and matched 50 Ω load in sequence. A measurement was made on 25 °C deionized water to verify that proper permittivity values were being obtained. Otherwise, the probe was calibrated again until measured permittivities values of water matched well with the known data. Typical error of the system was 5% after followed the standard calibration procedure. The entire analysis system was controlled by a computer. 2.3 Total sugar content and moisture content determination The total sugar content and moisture content were determined by refractometry according to AOAC methods ( AOAC 969.38B, 1996 ) using an Abbe-type refractometer (2WAJ, Shanghai Optical Instrument Factory, Shanghai, China) at 20 °C. Percentages of total sugar content and moisture content in honey samples were obtained from refractive index. 2.4 Sucrose content The sucrose contents in pure honey samples and sucrose syrups were measured by a high performance liquid chromatography (LC-2010AHT, Shimadzu Corporation, Kyoto, Japan) according to the procedure described by GB/T-18932.22-2003 (2003) . Fig. 1 is chromatograms from the HPLC analysis of sucrose contents for a standard sample according to GB/T-18932.22-2003 (2003) ( Fig. 1 a), jujube honey ( Fig. 1 b), yellow-locust honey ( Fig. 1 c) and milk-vetch honey ( Fig. 1 d), respectively. The peak of sucrose content appeared at about 9.395 min in Fig. 1 a. However, no peak at this time was found in jujube, yellow-locust and milk-vetch honey ( Fig. 1 c–d). Therefore, the sucrose contents of used jujube, yellow-locust and milk-vetch honey were less than the level (0.2%) that can be detected using the HPLC method under our experimental conditions ( Table 1 ). The honey samples used in the study were regarded as pure honey. 2.5 Ash content Samples of 5–10 g were weighed into a previously ignited crucible and placed under infrared lamp. The voltage of lamp increased slowly until the samples turned black. Then they were incinerated in a furnace at 600 °C overnight till constant weight before being cooled in desiccators and weighed ( AOAC 920.181, 1996 ). 2.6 Preparing sucrose syrup The sucrose-water mixture, consisted of 350 g sucrose and 350 g distilled water, were added in a 1000 ml flask with three openings. The masses of sucrose and water were measured with an electronic balance (FA2104A, Shanghai Precision & Scientific Instrument Co., Ltd., Shanghai, China) having precision of 0.0001 g. The flask was placed in an electric jacket (Model 98-1-B, Tianjin Taisite Instrument Co., Ltd., Tianjing, China). A stainless steel stick with a laminated end was inserted in solution and the other end was connected to a timing motor stirrer (Model JJ-1, Jiantan Danyangmen Quartz Glass Factory, Jintan, China) through the hole of a rubber plug that was used to block the central opening of flask. During heating, temperature of sucrose–water mixture was kept between 100 and 130 °C, and the mixture was continuously mixed by the timing motor stirrer to make sucrose melt in water evenly. The other two openings, which were fixed on a steel supporter to prevent the flask from moving during mixing, on each side of flask were open to air for water to evaporate during heating. About 10 g of distilled water was added to flask with a funnel at 20 min interval to create yellowish decocted sucrose syrup, similar to the color of the honey used in the present study. During mixing and heating, small amount of the sucrose solution was sampled with a glass stick from the flask (every 10 min) and total sugar content was measured at room temperature until the sucrose content was about 80%. The flask was then taken from electric jacket, covered and cooled at room temperature. According to this method, total three batches of sucrose syrup with total sugar content of 80.5%, 80.8% and 80.8% were made with corresponding moisture contents of 17.3%, 17.0% and 17.0%, respectively. The ash contents of these three batches of sucrose syrup were 0.55%. HPLC analysis showed no detectable other sugars except for sucrose in the final sucrose syrup. These samples were regarded as pure sucrose syrup. The syrup was used for measurement before noticeable crystal appeared. 2.7 Preparation and measurement of honey mixed with sucrose syrup Pure sucrose syrup were added to 50 g pure jujube, yellow-locust and milk-vetch honey to make honey adulterated with sucrose syrup (honey–sucrose syrup mixture) with different sucrose contents from 0% (pure honey) to about 80% (pure sucrose syrup) at about 8% interval based on w/w ratio at room temperature, respectively. The honey–sucrose syrup mixture at each sucrose content level was mixed evenly with a glass stick, and transferred to three beakers (10 ml each). Each beaker was placed on a 50 mm diameter support platform and raised to make downward open-ended coaxial-line probe immerged in sample for permittivity measurements. Since air bubble between the probe and sample significantly interfere with dielectric property measurement results, it was avoided during permittivity analysis. All measurements were conducted three times at room temperature (25 ± 1 °C). For each sample, total nine measurements were used to calculate the means and standard deviations. Significant differences between mean values for permittivity were determined by analysis of variance and mean separation by Duncan’s Mutiple Range Test at the 5% probability level. 3 Results and discussion 3.1 Dielectric constant of honey–sucrose syrup mixture The dielectric constants of three kinds of pure honey and sucrose syrup (80.5% sucrose) over the frequency range from 10 to 4500 MHz at room temperature (25 ± 1 °C) are shown in Fig. 2 . The results reveal that regardless of the pure honey samples or sucrose syrup, dielectric constants decreased as increasing frequency. This result is consistent with the findings for pure Chinese honey at the same frequency range ( Guo et al., 2010, 2011 ) and Indian honey from 900 to 2500 MHz ( Ahmed et al., 2007 ). The dielectric constant of pure sucrose syrup was lowest among the 4 samples at any given frequency. Previously published reports have demonstrated that moisture content significantly influenced dielectric properties of honey ( Guo et al., 2010; Puranik et al., 1991 ). However, the moisture content (17.3%) of the pure sucrose syrup was similar to that of the pure honey samples (17.1–18.1%). The difference in the dielectric constant values between the pure sucrose syrup and pure honey observed in the present study might result from different amount of minerals or ash content existing in the samples. The ash content in sucrose syrup was 0.55%, while it was ⩽0.07% for the pure honey. Ahmed et al. (2007) studied the dielectric behaviors of selected Indian honey containing different moisture and ash contents from 900 to 2500 MHz, and showed that honey samples which contained similar moisture content but different ash contents had significantly different permittivity values. Between 915 and 2450 MHz frequencies, the higher the ash content, the lower the average dielectric constant values. This finding is also in agreement with the analysis of salt on dielectric properties of fruits and vegetables ( Sipahioglu and Barringer, 2003 ), meat batter ( Zhang et al., 2007 ), aqueous solutions and simple meat mixtures ( Lyng et al., 2005 ), although no obvious correlation was found in egg album and yolk ( Guo et al., 2007 ). This occurs maybe due to the binding of free water molecules by counter ions of the dissolved salts ( Ryynänen, 1995 ). The dielectric constants of jujube honey–sucrose syrup mixtures with sucrose contents at six selected levels from 10 to 4500 MHz frequencies at room temperature are shown in Fig. 3 . The sucrose content did not influence the change trend of dielectric constant with frequency. Table 2 shows the means and standard deviations of dielectric constants of jujube honey–sucrose syrup mixtures (including 0% sucrose content or pour jujube honey, and pure sucrose syrup 80.5%) with various sucrose contents at four frequencies and room temperature, respectively. The selected frequencies are allocated for ISM (Industrial, Scientific and Medical) applications, i.e. radio frequencies 27 and 41 MHz, and microwave frequencies 915 and 2450 MHz. A few statistical significant differences ( P < 0.05) were found for dielectric constant at selected frequencies, but significant trends were not observed. However, the honey–sucrose syrup mixture had higher dielectric constant values than pure sucrose syrup at a given frequency. Because the water content of honey–sucrose syrup mixtures almost kept constant (from 17.3% in pure sucrose syrup to 17.5% in pure jujube honey), the different dielectric constants may be also caused by different ash content. Ash content increased with increasing sucrose content in mixture. The dielectric constant is decreased by the presence of ions, which bind water and reduce its mobility ( Bircan and Barringer, 2002 ) . Similar results were also found in honey–sucrose syrup mixture of yellow-locust and milk-vetch. Tables 3 and 4 list the means and standard deviations of dielectric constants of yellow-locust and milk-vetch–sucrose syrup mixtures with various sucrose contents at four frequencies and room temperature, respectively. 3.2 Dielectric loss factor of honey–sucrose syrup mixture Dielectric loss factors of pure jujube, yellow-locust and milk-vetch honey samples and sucrose syrup (80.5% sucrose) over the frequency range from 10 to 4500 MHz at room temperature are illustrated in Fig. 4 . Dielectric relaxations were existed in all tested samples ( Fig. 4 ). These similar results were also reported in our previous honey studies without sucrose treatments ( Guo et al., 2010, 2011 ). The relaxation frequencies of pure honey samples and sucrose syrup were not much different from each other. They were 67, 65, 57 and 63 MHz for pure jujube, yellow-locust, milk-vetch honey and sucrose syrup, respectively. However, the maximum average value of loss factor, which appeared at relaxation frequency, of sucrose syrup was much smaller than that of pure honey samples. They were between 9.05 and 9.32 for the pure honey samples as compared to 8.55 for the sucrose syrup. At frequencies above 40 MHz, the loss factor values of sucrose syrup became noticeably smaller than those of pure honey. These differences at higher frequency range might result from the differences in ash contents between pure sucrose syrup and pure honey samples. It has been shown that honey with higher ash content had smaller loss factor at microwave frequencies ( Ahmed et al., 2007 ) . The dielectric loss factors of jujube honey–sucrose syrup mixture with sucrose contents at the 6 selected levels from 10 to 4500 MHz frequencies at room temperature are shown in Fig. 5 . Dielectric relaxation was still existed in all samples, and the relaxation frequencies for the honey–sucrose mixture located between 67 and 63 MHz, which were relaxation frequencies of pure jujube honey and pure sucrose syrup, respectively. The loss factor decreased or increased with increasing sucrose content, which could be depended on the temperature and frequency. When equal to or larger than the relaxation frequency and 25 °C, the loss factor of each mixture decreased with increasing sucrose content ( Fig. 5 ). This was probably caused by the low solubility of sucrose, resulting in less hydrogen bonds due to stabilizing by adding more hydroxyl groups of sugars ( Liao et al., 2003 ). Our previously published study revealed that the relaxation frequency increased as moisture content increased from 18% to 42% in honey ( Guo et al., 2010 ). No obvious change in relaxation frequency in this study may be due to the similar moisture content in jujube honey–sucrose syrup mixture (17.3–17.5%). However, the peak value of loss factor decreased with increasing sucrose content. For example, it was 9.05, 8.95, 8.91, 8.76, 8.68, and 8.55 for the samples with 0%, 16.1%, 32.2%, 48.3%, 64.4% and 80.5% sucrose content, respectively. With increased sucrose content in honey–sucrose syrup mixture, the ash content increased from almost 0% in the pure honey to 0.55% in the pure sucrose syrup. Therefore, when the moisture content is almost constant, the higher ash content, the lower loss factor at microwave frequency. The same frequency- and sucrose content-dependent loss factor was also observed in honey–sucrose syrup mixture of yellow locust and milk-vetch honey. This is in good agreement with the similar relation in a model food at 2450 MHz ( Sakai et al., 2005 ). The means and standard deviations of dielectric loss factors of jujube, yellow-locust and milk-vetch honey–sucrose syrup mixtures with various sucrose contents at four frequencies and room temperature are shown in Tables 2–4 , respectively. Obvious statistical significant differences ( P < 0.05) at each frequency were noted. 3.3 Relationship between dielectric properties and sucrose content Linear relationships between dielectric constant or loss factor at 101 discrete frequencies from 10 to 4500 MHz and sucrose content in honey–sucrose syrup mixture were regressed. Results presented that there was no significant linear relationship between dielectric constant and sucrose contents in honey samples at any frequency. However, strong negative linear correlation between the dielectric loss factor and sucrose content around relaxation frequency was found. Fig. 6 presents the strongest linear regressions of dielectric loss factors on sucrose content at 104 MHz for jujube honey, 51 MHz for yellow-locust honey, and 63 MHz for milk-vetch honey. The linear relationships can be described as (1) ε ″ = aS + b where S represents sucrose content (%); a and b are slope and intercept of regressed line in Fig. 6 , respectively. For jujube honey, a = −0.0061, b = 8.8631 and R 2 = 0.996; for yellow-locust honey, a = −0.0083, b = 9.3431 and R 2 = 0.978; for milk-vetch honey, a = −0.0103, b = 9.2045 and R 2 = 0.978.If the dielectric loss factor of honey sample is known, the sucrose content can be calculated as: (2) S = ε ″ - b a The honey could be regarded as adulterated honey with sucrose syrup if the calculated S is higher than 5%. The smaller value of S , the higher purity of honey. This result makes developing a new sensor not only determining adulterated honey with sucrose syrup, but also predicting sucrose content in adulterated honey be possible. 4 Conclusions The dielectric constant of pure jujube, yellow-locust and milk-vetch honey, sucrose syrup and honey–sucrose syrup mixture decreased with increasing frequency over 10 to 4500 MHz range at room temperature. Dielectric constant of pure sucrose syrup was smaller compared with that of pure honey at any frequency. There was no significant linear correlation between dielectric constant and sucrose content in honey–sucrose syrup mixture. Dielectric relaxation was detected in pure honey, pure sucrose syrup and honey–sucrose syrup mixtures. The relaxation frequency of sucrose syrup was similar to that of pure honey. However, the loss factor of sucrose syrup was smaller than that of pure honey when frequency was higher than 40 MHz, especially at the region nearby its relaxation frequency. The maximum loss factor decreased with increasing sucrose content. Significant and strong negative linear correlation ( R 2 > 0.98) was found between dielectric loss factor and sucrose content around relaxation frequency in all honey–sucrose syrup mixtures. This study suggests that dielectric property could be used to detect sucrose–adulterated honey or sense sucrose content in honey. References Ahmed et al., 2007 J. Ahmed S.T. Prabhu G.S.V. Raghavan M. Ngadi Physico-chemical, rheological, calorimetric and dielectric behavior of selected Indian honey Journal of Food Engineering 79 4 2007 1207 1213 Al et al., 2009 M.L. Al D. Daniel A. Moise O. Bobis L. Laslo S. Bogdanov Physico-chemical and bioactive properties of different floral origin honeys from Romania Food Chemistry 112 4 2009 863 867 AOAC, 1996 AOAC, 1996. Official methods of analysis, 16th ed. Association of Official Analytical Chemists. Methods, Washington, DC, 969.38B, 920.181. Bircan and Barringer, 2002 C. Bircan S.A. Barringer Use of dielectric properties to detect egg protein denaturation Journal of Microwave Power and Electromagnetic Energy 37 2 2002 89 96 Bogdanov and Martin, 2002 S. Bogdanov P. Martin Honey authenticity: a review Mitt. Lebensm. Hyg. 93 2002 232 254 Codex Alimentarius Commission, 2001 Codex Alimentarius Commission, 2001. Revised codex standard for honey. Codex Standard 12-1981. Rev.1, 1987. Rev.2, 2001. GB/T-18932.22-2003, 2003 GB/T-18932.22-2003, 2003. Method for the determination of fructose, glucose, sucrose, maltose contents in honey-liquid chromatography refractive index detection method. GB18796-2005, 2005 GB18796-2005. (2005). Chinese national standards-honey. Guo et al., 2007 W. Guo S. Trabelsi S.O. Nelson D.R. Jones Storage effects on dielectric properties of eggs from 10 to 1800 MHz Journal of Food Science 72 5 2007 335 340 Guo et al., 2008 W. Guo G. Tiwari J. Tang S. Wang Frequency, moisture and temperature-dependent dielectric properties of chickpea flour Biosystems Engineering 101 2 2008 217 224 Guo et al., 2010 W. Guo X. Zhu Y. Liu H. Zhuang Sugar and water contents of honey with dielectric property sensing Journal of Food Engineering 97 2 2010 275 281 Guo et al., 2011 W. Guo Y. Liu X. Zhu S. Wang Temperature-dependent dielectric properties of honey associated with dielectric heating Journal of Food Engineering 102 3 2011 209 216 HG/T3462-1999, 1999 HG/T3462-1999. (1999). Chemical Industry Standards of P.R.C. Relating to Chemical Reagent--Sucrose. Içier and Baysal, 2004 F. Içier T. Baysal Dielectrical properties of foodmaterials-1: factors affecting and industrial uses Critical Reviews in Food Science and Nutrition 44 6 2004 465 471 Kent and Anderson, 1996 M. Kent D. Anderson Dielectric studies of added water in poultry meat and scallops Journal of Food Engineering 28 3–4 1996 239 259 Kent et al., 2001 M. Kent R. Knöchel F. Daschner U.-K. Berger Composition of foods including added water using microwave dielectric spectra Food Control 12 7 2001 467 482 Kent et al., 2002 M. Kent A. Peymann C. Gabriel A. Knight Determination of added water in pork products using microwave dielectric spectroscopy Food Control 13 3 2002 143 149 Liao et al., 2003 X.J. Liao G.S.V. Raghavan J.M. Dai V.A. Yaylayan Dielectric properties of alpha- d -glucose aqueous solutions at 2450 MHz Food Research International 36 5 2003 485 490 Lizhi et al., 2010 H. Lizhi K. Toyoda I. Ihara Discrimination of olive oil adulterated with vegetable oils using dielectric spectroscopy Journal of Food Engineering 96 2 2010 167 171 Lyng et al., 2005 J.G. Lyng L. Zhang N.P. Brunton A survey of the dielectric properties of meats and ingredients used in meat product manufacture Meat Science 69 4 2005 589 602 Ng et al., 2008 S.K. Ng P. Ainsworth A. Plunkett A.D. Haigh A.A.P. Gibson G. Parkinson Determination of added fat in meat paste using microwave and millimetre wave techniques Meat Science 79 4 2008 748 756 Perez-Arquillue et al., 1994 C. Perez-Arquillue P. Conchello A. Arino T. Juan A. Herresa Quality, evaluation of Spanish rosemary ( Rosomarinus officinalis ) honey Food Chemistry 51 1994 207 210 Puranik et al., 1991 S. Puranik A. Kumbharkhane S. Mehrotra Dielectric properties of honey-water mixtures between 10 MHz and 10 GHz using time domain technique Journal of Microwave Power and Electromagnetic Energy 26 4 1991 196 201 Ryynänen, 1995 S. Ryynänen The electromagnetic properties of food materials: a review of the basic principles Journal of Food Engineering 26 4 1995 409 429 Sakai et al., 2005 N. Sakai W.J. Mao Y. Koshima M. Watanabe A method for developing model food system in microwave heating studies Journal of Food Engineering 66 4 2005 525 531 Sipahioglu and Barringer, 2003 O. Sipahioglu S.A. Barringer Dielectric properties of vegetables and fruits as a function of temperature, ash, and moisture content Journal of Food Science 68 2003 234 239 Sosa-Morales et al., 2010 M.E. Sosa-Morales L. Valerio-Junco A. López-Malo H.S. García Dielectric properties of foods: reported data in the 21st Century and their potential applications LWT – Food Science and Technology 43 8 2010 1169 1179 Wang, 2003 Wang, B., 2003. Handbook on Food Sanitary Inspection. Shanghai: The Commercial Press, pp. 460–463 (in Chinese). Wang, 2007 Wang, H. (2007). Honey quality inspection and adulteration identification. Food and Nutrition in China (5), 57–60 (in Chinese). Zhang et al., 2007 L. Zhang J.G. Lyng N.P. Brunton The effect of fat, water and salt on the thermal and dielectric properties of meat batter and its temperature following microwave or radio frequency heating Journal of Food Engineering 80 1 2007 142 151
What problem does this paper attempt to address?
-
Measurement of Sugar Content of Watermelon Using Near-Infrared Reflectance Spectroscopy in Comparison with Dielectric Property
Xuemei Tao,Yidan Bao
DOI: https://doi.org/10.1117/12.710921
2006-01-01
Abstract:The sugar content of watermelon is important to its taste thus influences the market. It's difficult to know whether the melon is sweet or not for consumers. We tried to develop a convenient meter to determine the sugar of watermelon. The first objective of this paper was to demonstrate the feasibility of using a near-infrared reflectance spectrometer (NIRS) to investigate the relationship between sugar content of watermelon and absorption spectra. The NIRS reflectance of nondestructive watermelon was measured with a Visible/NIR spectrophotometer in 325-1075 nm range. The sugar content of watermelon was obtained with a handhold sugar content meter. The second objective was to measure the watermelon's dielectric property, such as dielectric resistance, capacitance, quality factor and dielectric loss. A digital electric bridge instrument was used to get the dielectric property. The experimental results show that they were related to watermelon's sugar content. A comparison between the two methods was made in the paper. The model derived from NIRS reflection is useful for class identification of Zaochun Hongyu watermelon though it's not quite accurate in sweetness prediction (the max. deviation is 0.7). Electric property bears little relation to sugar content of watermelon at this experiment and it couldn't be used as non-destructive inspection method.
-
Nondestructive Determination Of Diastase Activity Of Honey Based On Visible And Near-Infrared Spectroscopy
Zhenxiong Huang,Lang Liu,Guojian Li,Hong Li,Dapeng Ye,Xiaoli Li
DOI: https://doi.org/10.3390/molecules24071244
IF: 4.6
2019-01-01
Molecules
Abstract:The activities of enzymes are the basis of evaluating the quality of honey. Beekeepers usually use concentrators to process natural honey into concentrated honey by concentrating it under high temperatures. Active enzymes are very sensitive to high temperatures and will lose their activity when they exceed a certain temperature. The objective of this work is to study the kinetic mechanism of the temperature effect on diastase activity and to develop a nondestructive approach for quick determination of the diastase activity of honey through a heating process based on visible and near-infrared (Vis/NIR) spectroscopy. A total of 110 samples, including three species of botanical origin, were used for this study. To explore the kinetic mechanism of diastase activity under high temperatures, the honey of three kinds of botanical origins were processed with thermal treatment to obtain a variety of diastase activity. Diastase activity represented with diastase number (DN) was measured according to the national standard method. The results showed that the diastase activity decreased with the increase of temperature and heating time, and the sensitivity of acacia and longan to temperature was higher than linen. The optimum temperature for production and processing is 60 degrees C. Unsupervised clustering analysis was adopted to detect spectral characteristics of these honeys, indicating that different botanical origins of honeys can be distinguished in principal component spaces. Partial least squares (PLS) and least squares-support vector machine (LS-SVM) algorithms were applied to develop quantitative relationships between Vis/NIR spectroscopy and diastase activity. The best result was obtained through Gaussian filter smoothing-standard normal variate (GF-SNV) pretreatment and the LS-SVM model, known as GF-SNV-LS-SVM, with a determination coefficient (R-2) of prediction of 0.8872, and root mean square error (RMSE) of prediction of 0.2129. The overall results of this paper showed that the diastase activity of honey can be determined quickly and non-destructively with Vis/NIR spectral methods, which can be used to detect DN in the process of honey production and processing, and to maximize the nutrient content of honey.
-
A Novel, Rapid Screening Technique for Sugar Syrup Adulteration in Honey Using Fluorescence Spectroscopy
Sha Yan,Minghui Sun,Xuan Wang,Jihao Shan,Xiaofeng Xue
DOI: https://doi.org/10.3390/foods11152316
IF: 5.2
2022-08-04
Foods
Abstract:The adulteration of honey with different sugar syrups is common and difficult to detect. To ensure fair trade and protect the interests of apiarists, a rapid, simple and cost-effective detection method for adulterants in honey is needed. In this work, fluorescence emission spectra were obtained for honey and sugar syrups between 385 and 800 nm with excitation at 370 nm. We found substantial differences in the emission spectra between five types of honey and five sugar syrups and also found differences in their frequency doubled peak (FDP) intensity at 740 nm. The intensity of the FDP significantly declined (p < 0.01) when spiking honey with ≥10% sugar syrup. To validate this method, we tested 20 adulterant-positive honey samples and successfully identified 15 that were above the limit of detection. We propose that fluorescence spectroscopy could be broadly adopted as a cost-effective, rapid screening tool for sugar syrup adulteration of honey through characterization of emission spectra and the intensity of the FDP.
food science & technology
-
Comparison of Various Signal Processing Techniques and Spectral Regions for the Direct Determination of Syrup Adulterants in Honey Using Fourier Transform Infrared Spectroscopy and Chemometrics
Gerard Dumancas,Helena Ellis,Jossie Neumann,Khalil Smith
DOI: https://doi.org/10.3390/chemosensors10020051
2022-01-28
Chemosensors
Abstract:Honey consumption has become increasingly popular worldwide. However, the increase in demand for honey has also caused an increase in its adulteration, a deliberate fraud which involves adding of other substances to pure honey for economic purposes. This process not only lowers the quality of honey, but also has potential health risks, including high blood sugar, increased risk of diabetes, and weight gain. Herein, we develop an easy-to-use and direct method of quantifying corn, cane, beet, and rice syrup adulterants in honey using Fourier transform infrared spectroscopy and chemometrics. Various signal processing techniques, including derivatives, moving average, binning, Savitzky–Golay, and standard normal variate using the entire spectral region (3996–650 cm−1) and specific spectral region (1501–799 cm−1), were compared. Optimum results were obtained using first derivative signal processing for both the entire and specific spectral regions. The first derivative signal processing technique garnered the most optimum results using the specific spectral range (1501–799 cm−1) (RMSECVaverage = 0.021, RMSEPaverage = 0.014, R2average = 0.859) across all syrup adulterants. An exploratory analysis to assess the utility of this specific spectral region in pattern recognition of samples based on their adulterant content show that this region is effective in discriminating samples according to the presence or absence of honey syrup adulterants.
chemistry, analytical,electrochemistry,instruments & instrumentation
-
Rapid detection of sucrose adulteration in honey using Fourier transform infrared spectroscopy
Mehmet Fatih Cengiz,M. Zeki Durak
DOI: https://doi.org/10.1080/00387010.2019.1615957
2019-05-28
Spectroscopy Letters
Abstract:Honey authenticity is of great importance for commercial and health reasons. The most common adulteration methods are overfeeding of bees with sugar or by adding sucrose. In the study, a Fourier transform infrared spectroscopy based on chemometric method, a partial least squares, for determination of sucrose sirup adulteration of Turkish honeys was improved. For this purpose, honey samples were adulterated with known amounts of sucrose sirup in concentrations ranging between 5.94 and 27.80%. A calibration curve was constructed within 992–923 cm<sup>−1</sup> with the regression coefficient of 0.999. Obtained results from the spectra were confirmed by high performance liquid chromatography-refractive index detector and a good correlation was found between the results of the spectroscopic and chromatographic methods. Additionally, some method validation parameters (linearity, repeatability, limit of detection, and quantification) of the spectroscopic method were studied and obtained results were compared with chromatographic method. To prove the usefulness of the method, twenty different honey samples were collected from markets in Turkey and analyzed for sucrose contents. The results indicated that predicted sucrose concentration of honey samples by the spectroscopic method ranged between 4.52 and 15.16% and results were confirmed by the chromatographic method with high correlation (correlation coefficient = 92%). The results of the present indicated showed that adulteration ratio of honey samples by sugar addition can be detected using Fourier transform infrared spectroscopy technique in a short time with high accuracy. In conclusion, this method could be regarded as a new alternative technique for routine analysis in quality control of honey samples.
spectroscopy
-
Fast Quantification of Honey Adulteration with Laser-Induced Breakdown Spectroscopy and Chemometric Methods
Jiyu Peng,Weiyue Xie,Jiandong Jiang,Zhangfeng Zhao,Fei Zhou,Fei Liu
DOI: https://doi.org/10.3390/foods9030341
IF: 5.2
2020-01-01
Foods
Abstract:Honey adulteration is a major issue in food production, which may reduce the effective components in honey and have a detrimental effect on human health. Herein, laser-induced breakdown spectroscopy (LIBS) combined with chemometric methods was used to fast quantify the adulterant content. Two common types of adulteration, including mixing acacia honey with high fructose corn syrup (HFCS) and rape honey, were quantified with univariate analysis and partial least squares regression (PLSR). In addition, the variable importance was tested with univariable analysis and feature selection methods (genetic algorithm (GA), variable importance in projection (VIP), selectivity ratio (SR)). The results indicated that emissions from Mg II 279.58, 280.30 nm, Mg I 285.25 nm, Ca II 393.37, 396.89 nm, Ca I 422.70 nm, Na I 589.03, 589.64 nm, and K I 766.57, 769.97 nm had compact relationship with adulterant content. Best models for detecting the adulteration ratio of HFCS 55, HFCS 90, and rape honey were achieved by SR-PLSR, VIP-PLSR, and VIP-PLSR, with root-mean-square error (RMSE) of 8.9%, 8.2%, and 4.8%, respectively. This study provided a fast and simple approach for detecting honey adulteration.
-
Impact of Different Adulterants on Honey Quality Properties and Evaluating Different Analytical Approaches for Adulteration Detection
Teferi Damto,Ashagrie Zewdu,Tarekegn Birhanu
DOI: https://doi.org/10.1016/j.jfp.2024.100241
Abstract:The study was carried out keeping in view the recently emerging concern of adulteration of natural honey on the honey markets. This study intended to investigate honey adulteration detection using physical and chemical composition to achieve a foreign component (a marker) that is present in the honey that confirms either the adulteration or authenticity of the honey. The technique was evaluated on honey samples that were 5-50% adulterated with various common adulterants in Ethiopia. Preliminary quick tests and characterization of physicochemical and antioxidant properties were tested as alternative analytical approaches for honey adulteration detection. Preliminary quick test methods were used to detect adulterated honey, but these methods were found specific to adulterant materials. The proline and pH levels decreased as molasses, sugar, and banana adulterants increased, while increased as melted candy and shebeb adulterants increased. Moisture content decreased as sugar, melted candy, and shebeb adulterants were increased, while decreased as molasses and banana adulterants increased. HMF content increased as molasses, melted candy, and shebeb adulterants were increased. The sugar compositions are key differential criteria to detect the adulteration of honey with sugar. Based on their physical characteristics, PCA demonstrated a considerable difference between samples of pure and contaminated honey. In conclusion, it was observed that honey adulteration was detected based on significant deviations of physicochemical and biochemical components from expected values in the concentration of naturally occurring components. This study successfully demonstrated a method to rapidly and accurately classify and authenticate honey. Accordingly, it is recommended that frequent training for stakeholders on adulteration detection methods should be carried out to avoid adulteration of honey from the markets.
-
Non-targeted method to detect honey adulteration: Combination of electrochemical and spectrophotometric responses with principal component analysis
Cristiane Guellis,Daniele C. Valério,Guilherme G. Bessegato,Marcela Boroski,Josiane C. Dragunski,Cleber A. Lindino
DOI: https://doi.org/10.1016/j.jfca.2020.103466
IF: 4.3
2020-06-01
Journal of Food Composition and Analysis
Abstract:Detecting adulteration in honey is not an easy task and most of the traditional methods are usually unaffordable. Thus, we describe the use of cyclic voltammetry using Cu/CuO electrode and UV–vis spectrophotometry along with chemometric tools to detect adulteration of honey with corn syrup. Both honey and corn syrup samples presented an anodic peak at +1.1 V, but the current is variable and depends on the sample composition in relation to the honey and syrup content. A cathodic peak at +0.42 V arises at higher scan rates, which is more pronounced for syrup samples and can be used to discriminate between pure and adulterated samples. This response can be combined with UV/vis absorbance peaks at 285 and 216 nm to identify adulteration. Principal component analysis (PCA) and hierarchical cluster analysis (HCA) allowed differentiating between honey and corn syrup samples and simulated mixtures of them, in which the first two principal components together explain 100.0 % of the data variability, specifically 98.47 % by PC1 and 1.53 % by PC2. The method requires a minimum amount of sample and generates a low amount of waste. Furthermore, it is possible to use portable and cheap equipment, making it more accessible to the beekeeper sector.
food science & technology,chemistry, applied
-
Determination of Possible Adulteration and Quality Assessment in Commercial Honey
Didem P. Aykas
DOI: https://doi.org/10.3390/foods12030523
IF: 5.2
2023-01-25
Foods
Abstract:This study aims to predict several quality traits in commercial honey samples simultaneously and to reveal possible honey adulteration using a field-deployable portable infrared spectrometer without any sample preparation. A total of one hundred and forty-seven commercial honey samples were purchased from local and online markets in Turkey and the United States of America (USA), and their soluble solids (°Brix), pH, free acidity, moisture, water activity (aw), glucose, fructose, sucrose, and hydroxymethyl furfural (HMF) contents were determined using reference methods. The HMF (n = 11 samples) and sucrose (n = 21) concentrations were higher than the regulatory limits in some tested samples. The exceeding HMF content may imply temperature abuse during storage and prolonged storing. On the other hand, high sucrose content may indicate possible adulteration with commercial sweeteners. Therefore, soft independent modeling of class analogies (SIMCA) analysis was conducted to reveal this potential sweetener adulteration in the samples, and the SIMCA model was able to identify all the flagged samples. The suggested FT-IR technique may be helpful in regulatory bodies in determining honey authenticity issues as well as assessing the quality characteristics of honey samples in a shorter period and at a lower cost.
food science & technology
-
Hydroxymethylfurfural Content and Sugar Profile of Honey Available in Bangladesh Using Validated HPLC-PDA and HPLC-RID
S. Das,M.N. Uddin,M.S. Haque,D. Chakraborty,M. Mostafa,A. Hasnaine,S.K. Das,M. Uddin
DOI: https://doi.org/10.18502/jfqhc.9.3.11154
2022-11-14
Journal of Food Quality and Hazards Control
Abstract:Background: Honey has a lot of reputation because of its supposed medicinal properties. In this study, Hydroxymethylfurfural (HMF), sugars, and Fructose/Glucose ratio of honey in Bangladesh were assessed for adulteration and authenticity evaluation.
Methods: Seventy honey samples collected from different districts of Bangladesh were analyzed by High Performance Liquid Chromatography (HPLC) for HMF content and sugar profile. The samples were prepared by using Carrez I and Carrez II prior to injecting into HPLC. The samples were then filtered through syringe filter and taken in 1.5 ml vial for injecting into the HPLC system.
Results: HMF values were ranging from 1.41 mg/kg to 2,063.90 mg/kg. The Limit of Detection (LOD) and Limit of Quantification (LOQ) was found 0.10 mg/kg and 0.33 mg/kg with R2=0.9994. The average values of fructose, glucose, and sucrose were in the range of 14.75-52.44%, 8.19-42.63%, and 0.10-21.12%, respectively. From validation parameters, LOD values for fructose, glucose, and sucrose were 0.003, 0.008, and 0.004%, respectively; and LOQ values were 0.01, 0.028, and 0.015%, respectively with an excellent linearity with R2 for fructose=1.0, glucose=0.9999, and sucrose=1.0.
Conclusion: Some samples had higher HMF content which may be due to the storage time was increased and improper processing with high temperature or adulteration by High Fructose Corn Syrup (HFCS), sugar cane syrup, rice syrups or rice molasses. The sugar profiles showed that the most of honey samples were nectar honeys.
-
Differentiation of High-Fructose Corn Syrup Adulterated Kelulut Honey Using Physicochemical, Rheological, and Antibacterial Parameters
Rinee Najwa Mohamat,Nur Rabiatul Adawiah Mohammad Noor,Yus Aniza Yusof,Suriana Sabri,Norhasnida Zawawi
DOI: https://doi.org/10.3390/foods12081670
IF: 5.2
2023-04-18
Foods
Abstract:Kelulut (stingless bee) honey (KH) possesses a wide range of benefits for human consumption and can exhibit medical effects. Due to its high value, this premium honey is often adulterated with different types of cheaper sugars, causing low nutrients and potential food safety threats in the final product. This study aims to determine the physicochemical, rheological, and antibacterial properties of sugar-based adulterated KH from the stingless bee species Heterotrigona itama. Adulterated samples were prepared using pure honey mixed with different concentrations of high fructose corn syrup (HFCS), i.e., 10%, 20%, 30%, 40%, and 50%. Water activity, colour, total soluble solids, pH, turbidity, viscosity, and antimicrobial activity of KH were determined. In addition, the primary sugar composition (fructose, glucose, and trehalulose) was determined by high-performance liquid chromatography with evaporative light-scattering detection (HPLC-ELSD). This study shows that the increasing percentage of HFCS addition in the KH samples significantly increases (p < 0.05) the total soluble solids, colour, pH, turbidity, viscosity, glucose, and fructose content; meanwhile, the water activity and trehalulose were reduced significantly (p < 0.05). Antimicrobial activity against S. aureus was reduced significantly (p = 0.006) by an increased percentage of HFCS compared to Control. Antimicrobial activity against P. aeruginosa was also found to be reduced significantly but showed non-significant effect from an increased percentage of HFCS in honey (p = 0.413). The bacterium S. aureus was more vulnerable to treatment with honey from both Control and adulterated groups compared to P. aeruginosa. In conclusion, HFCS-adulterated KH and authentic KH can be differentiated using all the parameters investigated. These data are vital for the governing bodies to ensure that KH sold in the markets is free from HFCS adulteration.
food science & technology
-
Detection of Sugar Syrups in Honey Using Untargeted Liquid Chromatography–Mass Spectrometry and Chemometrics
Jule Hansen,Christof Kunert,Kurt-Peter Raezke,Stephan Seifert
DOI: https://doi.org/10.3390/metabo14110633
IF: 4.1
2024-11-23
Metabolites
Abstract:Background: Honey is one of the most adulterated foods worldwide, and several analytical methods have been developed over the last decade to detect syrup additions to honey. These include approaches based on stable isotopes and the specific detection of individual marker compounds or foreign enzymes. Proton nuclear magnetic resonance (1H-NMR) spectroscopy is applied as a rapid and comprehensive screening method, which also enables the detection of quality parameters and the analysis of the geographical and botanical origin. However, especially for the detection of foreign sugars, 1H-NMR has insufficient sensitivity. Methods: Since untargeted liquid chromatography–mass spectrometry (LC-MS) is more sensitive, we used this approach for the detection of positive and negative ions in combination with a recently developed data processing workflow for routine laboratories based on bucketing and random forest for the detection of rice, beet and high-fructose corn syrup in honey. Results: We show that the distinction between pure and adulterated honey is possible for all three syrups, with classification accuracies ranging from 98 to 100%, while the accuracy of the syrup content estimation depends on the respective syrup. For rice and beet syrup, the deviations from the true proportion were in the single-digit percentage range, while for high-fructose corn syrup they were much higher, in some cases exceeding 20%. Conclusions: The approach presented here is very promising for the robust and sensitive detection of syrup in honey applied in routine laboratories.
biochemistry & molecular biology
-
Rapid Identification of Corn Sugar Syrup Adulteration in Wolfberry Honey Based on Fluorescence Spectroscopy Coupled with Chemometrics
Shengyu Hao,Jie Yuan,Qian Wu,Xinying Liu,Jichun Cui,Hongzhuan Xuan
DOI: https://doi.org/10.3390/foods12122309
IF: 5.2
2023-06-09
Foods
Abstract:Honey adulteration has become a prominent issue in the honey market. Herein, we used the fluorescence spectroscopy combined with chemometrics to explore a simple, fast, and non-destructive method to detect wolfberry honey adulteration. The main parameters such as the maximum fluorescence intensity, peak positions, and fluorescence lifetime were analyzed and depicted with a principal component analysis (PCA). We demonstrated that the peak position of the wolfberry honey was relatively fixed at 342 nm compared with those of the multifloral honey. The fluorescence intensity decreased and the peak position redshifted with an increase in the syrup concentration (10–100%). The three-dimensional (3D) spectra and fluorescence lifetime fitting plots could obviously distinguish the honey from syrups. It was difficult to distinguish the wolfberry honey from another monofloral honey, acacia honey, using fluorescence spectra, but it could easily be distinguished when the fluorescence data were combined with a PCA. In all, fluorescence spectroscopy coupled with a PCA could easily distinguish wolfberry honey adulteration with syrups or other monofloral honeys. The method was simple, fast, and non-destructive, with a significant potential for the detection of honey adulteration.
food science & technology
-
The Experiment of The Simple High-Frequency Sensor to Detect The Degree of Brix in Sucrose Solutions
Nutdechatorn Puangngernmak,Thanarak Srisurat
DOI: https://doi.org/10.1109/ecti-con47248.2019.8955352
2019-07-01
Abstract:The degree of Brix is very useful for the food and beverage industry and manufacturing to measure the approximate sugar in raw material as fruit that defines the nutrition or chemical properties. Many techniques as Specific gravity, Refraction index, and Infrared absorption are used for measurement with a specific instrument. The high-frequency measurement with the electromagnetic sensor is another technique for detecting with dielectric properties of liquid under test. This paper proposes the high-frequency electromagnetic sensor that prototyping base on an open-end coaxial model with a monopole structure. The optimization of the structural dimension is processed by measuring the complex permittivity of the standard solution with different Brix content (5-25%). The customizing sensor can be Brix detector with resonance frequency from 0.972 to 1.028GHz and level of magnitude of reflection coefficient at frequency 0.958 GHz from -14.3 to -5.8dB
-
Application of Spatial Offset Raman Spectroscopy (SORS) and Machine Learning for Sugar Syrup Adulteration Detection in UK Honey
Mennatullah Shehata,Sophie Dodd,Sara Mosca,Pavel Matousek,Bhavna Parmar,Zoltan Kevei,Maria Anastasiadi
DOI: https://doi.org/10.3390/foods13152425
IF: 5.2
2024-07-31
Foods
Abstract:Honey authentication is a complex process which traditionally requires costly and time-consuming analytical techniques not readily available to the producers. This study aimed to develop non-invasive sensor methods coupled with a multivariate data analysis to detect the type and percentage of exogenous sugar adulteration in UK honeys. Through-container spatial offset Raman spectroscopy (SORS) was employed on 17 different types of natural honeys produced in the UK over a season. These samples were then spiked with rice and sugar beet syrups at the levels of 10%, 20%, 30%, and 50% w/w. The data acquired were used to construct prediction models for 14 types of honey with similar Raman fingerprints using different algorithms, namely PLS-DA, XGBoost, and Random Forest, with the aim to detect the level of adulteration per type of sugar syrup. The best-performing algorithm for classification was Random Forest, with only 1% of the pure honeys misclassified as adulterated and <3.5% of adulterated honey samples misclassified as pure. Random Forest was further employed to create a classification model which successfully classified samples according to the type of adulterant (rice or sugar beet) and the adulteration level. In addition, SORS spectra were collected from 27 samples of heather honey (24 Calluna vulgaris and 3 Erica cinerea) produced in the UK and corresponding subsamples spiked with high fructose sugar cane syrup, and an exploratory data analysis with PCA and a classification with Random Forest were performed, both showing clear separation between the pure and adulterated samples at medium (40%) and high (60%) adulteration levels and a 90% success at low adulteration levels (20%). The results of this study demonstrate the potential of SORS in combination with machine learning to be applied for the authentication of honey samples and the detection of exogenous sugars in the form of sugar syrups. A major advantage of the SORS technique is that it is a rapid, non-invasive method deployable in the field with potential application at all stages of the supply chain.
-
Physicochemical analysis and determination of di- and tri-saccharide content in Longan, Litchi and Siam weed honeys of Thailand
Penpun Wetwitayaklung,Worrakanya Narakornwit,Lawan Sratthaphut,Bunyapa Wangwattana
DOI: https://doi.org/10.1080/00218839.2017.1411183
2018-01-01
Journal of Apicultural Research
Abstract:Honeys produced by bees from the nectars of longan, litchi and Siam weed growing in Thailand were analyzed for physicochemical profiles (moisture, Brix%, soluble solids, density, viscosity, pH, free acid, electrical conductivity, HMF, DN, proline, color, flavonoid and antioxidant activities) and their carbohydrates quantified as monosaccharides, disaccharides and trisaccharides. All physicochemical parameters met the regulation requirements under the Codex Alimentarius Standard, EU Council and directives legislation of the Ministry of Public Health of Thailand, except the HMF value of one sample. The conductivity, color [Abs]450 and antioxidant activity were parameters that showed that there are significant differences in means between the groups of honey samples based on one way analysis of variance (ANOVA) (p < 0.05). The amounts of palatinose and isomaltose in the honey samples were statistical significantly different (ANOVA, p < 0.05). The differences between longan, litchi and Siam weed honeys by principle component analysis visible from the di- and trisaccharide profiles from an Rtx-65TG column were shown to be different from those from an SPB-1 column. The PC1 from the Rtx-65TG column profile was a linear combination that summarized 54.0% of the cumulative proportion of variance. The differences between the honey samples appeared to stem from many parameters and quantification compositions of the saccharides. The palatinose and isomaltose in longan honey were suggested to be markers for its authentication.
entomology
-
Tracing Floral and Geographical Origins of Honeys by Potentiometric and Voltammetric Electronic Tongue
Zhenbo Wei,Jun Wang
DOI: https://doi.org/10.1016/j.compag.2014.07.014
IF: 8.3
2014-01-01
Computers and Electronics in Agriculture
Abstract:A potentiometric electronic tongue (PE-tongue) and a voltammetric electronic tongue (VE-tongue) were used as rapid techniques to classify and predict the honey samples from different floral and geographical origins. The PE-tongue, which was named alpha-ASTREE, was developed by Alpha M.O.S. (Toulouse, France), and it comprises seven potentiometric chemical sensors. The VE-tongue was self-developed at Zhejiang University and comprises six metallic working sensors. Four types of honey of different floral origins (acacia, buckwheat, data, and motherwort) and four types of acacia honey of different geographical origins were classified by both multisensor systems. Multivariate statistical data analysis techniques such as principal component analysis (PCA) and discriminant function analysis (DFA) were used to classify the honey samples. Both types of electronic tongue have good potential to classify the honey samples, and the positions of the data point for the samples in the PCA score plots based on the VE-tongue were much more closely grouped. Three regression modes, principal component regression (PCR), partial least squares regression (PLSR), and least squared-support vector machines (LS-SVM), were applied for category forecasting. These regression models exhibited a clear indication of the prediction ability of the two types of electronic tongue, and a positive trend in the prediction of the floral and geographical origin of honey was found. Moreover, the performance of these regression models for predicting the four types of honey of different geographical origins by the VE-tongue is very stable. (C) 2014 Elsevier B.V. All rights reserved.
-
A validated method for the quantitative determination of sugars in honey using high-performance thin-layer chromatography
Md Khairul Islam,Tomislav Sostaric,Lee Yong Lim,Katherine Hammer,Cornelia Locher
DOI: https://doi.org/10.1007/s00764-020-00054-9
2020-10-01
Abstract:Sugars, in particular glucose and fructose, are the main constituents of honey, comprising up to 85% of its total weight. A high-performance thin-layer chromatography (HPTLC) method to identify and quantify common sugars (glucose, fructose and sucrose) in honey has been developed and fully validated according to the International Conference on Harmonisation guidelines. It allows to determine a honey's fructose-to-glucose ratio, which is not only an important authentication and quality control parameter, but also an indication of its tendency to crystallise. The HPTLC analysis is easy to perform, accurate, precise, specific and sensitive and requires only minimal sample preparation. With a limit of detection/limit of quantification of 21.98 ng/66.62 ng for fructose, 33.00 ng/100.00 ng for glucose and 21.17 ng/64.15 ng for sucrose, the sensitivity of the method has been greatly improved compared to other HPTLC-based approaches. An additional advantage is the method's simplicity and fast processing time as it only requires a single development step without plate or sample pre-treatment.
-
Characterization and Classification of Spanish Honeydew and Blossom Honeys Based on Their Antioxidant Capacity
Mónica Fernández-Estellé,Víctor Hernández-González,Javier Saurina,Oscar Núñez,Sonia Sentellas
DOI: https://doi.org/10.3390/antiox12020495
IF: 7.675
2023-02-17
Antioxidants
Abstract:Honey is a very appreciated product for its nutritional characteristics and its benefits for human health, comprising antioxidant, anti-inflammatory, antifungal, and antibacterial activities. These attributes depend on the specific composition of each honey variety, with the botanical origin as one of the distinctive features. Indeed, honeydew and blossom honeys show different physicochemical properties, being the antioxidant capacity, mainly relying on the phenolic compound content, one of the most important. In this work, Folin–Ciocalteu (FC) index, total flavonoid content (TFC), and the antioxidant capacity based on the ferric reducing antioxidant power (FRAP) assay were determined for a total of 73 honeys (50 blossom honeys and 23 honeydew honeys). Mean content of oxidizable species (FC index) ranges from 0.17 to 0.7 mg eq. gallic acid g−1, with honeydew honeys being the ones with higher values. Regarding TFC, mean values above 1.5 mg eq. quercetin g−1 (method applied in the absence of NaNO2) were obtained for honeydew honeys and heather honey. Lower and not discriminatory values (below 0.3 mg eq. epicatechin g−1) were obtained in the presence of NaNO2. The maximum antioxidant capacity was observed for thyme honeys (2.2 mg eq. Trolox g−1) followed by honeydew and heather honeys. Individually, only the FC index was able to discriminate between honeydew and blossom honeys, while the other spectroscopic indexes tested allowed the differentiation of some honey types according to the botanical origin. Thus, a holistic treatment of the results was performed using partial least square discriminant analysis (PLS-DA) for classification purposes using FC, TFC, and FRAP results as data. Honeydew and blossom honey were satisfactorily discriminated (error 5%). In addition, blossom honeys can be perfectly classified according to their botanical origin based on two-class PLS-DA classification models.
biochemistry & molecular biology,chemistry, medicinal,food science & technology
-
Magnetic dispersive solid-phase extraction based on a novel adsorbent for the detection of triazole pesticide residues in honey by HPLC-MS/MS
Qiongchen Miao,Jianmei Wang,Jing Nie,Huizhen Wu,Yanping Liu,Zuguang Li,Mingrong Qian
DOI: https://doi.org/10.1039/c6ay00376a
IF: 3.1
2016-01-01
Analytical Methods
Abstract:A novel Fe3O4@MDN magnetic nanomaterial was successfully developed as a magnetic dispersive solid-phase extraction adsorbent for the determination of triazole pesticide residuals in honey samples by high performance liquid chromatography coupled with triple quadrupole mass spectrometry (HPLC-MS/MS). The macromolecular structure named MDN was coated on the surface of a copolymer synthesized with silyl reagents methacrylic acid-3-(trimethoxysilyl) propyl ester (MPS) and tetraethyl orthosilicate (TEOS) based on ferriferrous oxide (Fe3O4), whose characteristics were confirmed by a scanning electron microscope (SEM). The proposed magnetic dispersive solid-phase extraction (MDSPE) method provided a rapid, environmentally friendly and magnetic stuff recyclable approach for the triazole pesticide analysis. By means of optimal conditions, the recoveries of 15 triazoles (spiked at 20 mu g kg(-1)) ranged from 90.5 to 105.9%. The method showed good linearity, sensitivity in the range of mu g per kilogram and repeatability (relative standard deviation below 6.8%, n = 5). The proposed method was confirmed to be a simple, rapid and efficient method for the analysis of triazole pesticide residuals in honey samples.