Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Crystallization of a Vitrified Hindered Phenol Within Chlorinated Polyethylene and Its Effects on Dynamic Mechanical Properties

Effects of Crystallization Temperature of Poly(vinylidene Fluoride) on Crystal Modification and Phase Transition of Poly(butylene Adipate) in Their Blends: a Novel Approach for Polymorphic Control.

Crystallization kinetics and crystalline structure of biodegradable Poly(ethylene adipate)

Crystallization behaviour of hindered phenol on chlorinated polyethylene matrix

The Structure and Dynamic Properties of Thermoplastic Polyurethane Elastomer/Hindered Phenol Hybrids

Dynamic Mechanical Properties and Morphologies of Organic Hybrids Consisting of Chlorinated Polyethylene and Hindered Phenol

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Studies on Nonisothermal Crystallization of Ultra–high Molecular Weight Polyethylene in Liquid Paraffin

Crystalline Structure and Morphology of a Hindered Phenol in a Chlorinated Polyethylene Matrix

Effects of Molecule Aggregation State on Dynamic Mechanical Properties of Chlorinated Polyethylene/Hindered Phenol Blends

Viscoelasticity of A Vitrified Hindered Phenol Compound During Thermal Annealing

Organic Hybrid of Chlorinated Polyethylene and Hindered Phenol. I. Dynamic Mechanical Properties

Dynamic Properties of an Organic Hybrid of Chlorinated Polyethylene and Hindered Phenol Compound

The Crystallinity of Pvc and Its Effect on Physical Properties

Organic Hybrid of Chlorinated Polyethylene and Hindered Phenol. II. Influence of the Chemical Structure of Small Molecules on Viscoelastic Properties

Changes in Dynamic Mechanical Properties and Structure of an Organic Hybrid of Chlorinated Polyethylene and Hindered Amine During Heat-Treatment Process.

Viscoelastic Properties of Organic Hybrids Consisting of Chlorinated Polyethylene and Hindered Phenol.

Crystallization Behavior and Morphology of Novel Aliphatic Poly (Monothiocarbonate)s

Organic Hybrid of Chlorinated Polyethylene and Hindered Phenol. III. Influence of the Molecular Weight and Chlorine Content of the Polymer on the Viscoelastic Properties

The influence of dynamic crosslinked topology and bond exchange on thermal properties, viscoelasticity, and foaming behavior of multibranched TPEE vitrimer

Dynamic Properties of Carbon Black Filled Chlorinated Polyethylene/hindered Phenol Blends