Abstract:Proton exchange membranes (PEMs) are often used in microbial fuel cells (MFCs) to separate the liquid in the anode and cathode chambers while allowing protons to pass between the chambers. However, negatively or positively charged species present at high concentrations in the medium can also be used to maintain charge balance during power generation. An anion exchange membrane (AEM) produced the largest power density (up to 610 mW/m2) and Coulombic efficiency (72%) in MFCs relative to values achieved with a commonly used PEM (Nafion), a cation exchange membrane (CEM), or three different ultrafiltration (UF) membranes with molecular weight cut offs of 0.5K, 1K, and 3K Daltons in different types of MFCs. The increased performance of the AEM was due to proton charge-transfer facilitated by phosphate anions and low internal resistance. The type of membrane affected maximum power densities in two-chamber, air-cathode cube MFCs (C-MFCs) with low internal resistance (84-91 omega for all membranes except UF-0.5K) but not in two-chamber aqueous-cathode bottle MFCs (B-MFCs) due to their higher internal resistances (1230-1272 omega except UF-0.5K). The UF-0.5K membrane produced very high internal resistances (6009 omega, B-MFC; 1814omega, C-MFC) and was the least permeable to both oxygen (mass transfer coefficient of k(O) = 0.19 x 10(-4) cm/s) and acetate (k(A) = 0.89 x 10(-8) cm/s). Nafion was the most permeable membrane to oxygen (k(O) = 1.3 x 10(-4) cm/s), and the UF-3K membrane was the most permeable to acetate (k(A) = 7.2 x 10(-8) cm/s). Only a small percent of substrate was unaccounted for based on measured Coulombic efficiencies and estimates of biomass production and substrate losses using Nafion, CEM, and AEM membranes (4-8%), while a substantial portion of substrate was lost to unidentified processes for the UF membranes (40-89%). These results show that many types of membranes can be used in two-chambered MFCs, even membranes that transfer negatively charged species.

Application of Ion Exchange Membrane in Packing-type Microbial Fuel Cell

Ion Exchange Membrane Cathodes For Scalable Microbial Fuel Cells

Microfiltration Membrane Performance in Two-Chamber Microbial Fuel Cells

Power generation using different cation, anion, and ultrafiltration membranes in microbial fuel cells

Enhancing the stability of power generation of single-chamber microbial fuel cells using an anion exchange membrane

Key Materials and Progress of Fuel Cells

Fuel Permeability of Anion Exchange Membranes under Electric Field

Vermiculite nanosheet augmented novel proton exchange membrane for microbial fuel cell

Effect of cathode electron acceptors on simultaneous anaerobic sulfide and nitrate removal in microbial fuel cell

Performance evaluation of microbial fuel cell using a radiation synthesized low density polyethylene-grafted-poly (glycidyl methacrylate-co-vinyl acetate) as a proton exchange membrane

Effect of the Membrane Electrode Assemble Design on the Performance of Single Chamber Microbial Fuel Cells

Improved Performance of Single-Chamber Microbial Fuel Cells Through Control of Membrane Deformation.

Role and Important Properties of a Membrane with Its Recent Advancement in a Microbial Fuel Cell

Development of a Novel Composite Polymer Electrolyte Membrane for Application as a Separator in a Dual Chamber Microbial Fuel Cell

Doped polymethyl methacrylate (PMMA) as proton exchange membrane for microbial fuel cell

Recent advances in the separators for microbial fuel cells.

Next‐Generation Proton‐Exchange Membranes in Microbial Fuel Cells: Overcoming Nafion's Limitations

Continuous Flowing Membraneless Microbial Fuel Cells with Separated Electrode Chambers

A Membrane Electrode Assembly Typed Microbial Fuel Cell for Electricity Generation

Patterned Ion Exchange Membranes for Improved Power Production in Microbial Reverse-Electrodialysis Cells

Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.