Abstract:We developed a finite element model to simulate the fused deposition modeling (FDM) process. The model considers the coupled thermal and mechanical analysis and incorporates the element activation function to mimic the additive nature of FDM. Due to repetitive heating and cooling in the FDM process, residual stresses accumulate inside the part during the deposition. The model is also used to evaluate the part distortions, revealing distortion features such as vaulting shapes and distortion-core shifting. A parametric study, three factors and three levels, was performed to evaluate the effects of the deposition parameters on residual stresses and part distortions. Prototype models with larger sizes were fabricated, measured, and compared with the simulations. The simulation results show that (1) the scan speed is the most significant factor to part distortions, followed by the layer thickness, (2) the road width alone is insignificant, however, the interaction between the road width and the layer thickness is significant too, and (3) there are other two-way and three-way interactions that are of secondary significance. Residual stresses increase with the layer thickness, and increase with the road width, to a less extent though, yet largely affected by the layer thickness. The FDM part distortions from the experiment show a similar trend as in the simulations, but no quantitative correlation. Introduction FDM is one of widely used solid freeform fabrication (SFF) systems because of the inexpensive machinery and durable part materials. In FDM, the thermoplastic material is heated to a semi-molten state and then extruded as an ultra-thin filament. While the extrusion nozzle is moving according to the toolpath defined by the part cross-sectional boundary, the material is deposited atop the previous layer and heat dissipation by conduction and forced convection causes the material to quickly solidify with the surrounding filaments. The bonding between filaments encompasses the local re-melting of the previously solidified material and diffusion [1]. Part geometry in SFF has been a frequently studied topic. Recently, Mahesh et al. used a benchmark part to evaluate several SFF processes and the measured tolerances such as flatness and symmetry were compared [2]. The authors noted that the residual-stress induced distortions (e.g. warpage and delamination) are prominent. As other SFF processes, in FDM, the heating and rapid cooling cycles of the work materials will aggravate non-uniform thermal gradients and cause stress build-up that consequently results in part distortions. Qiu et al. studied the toolpath effects in FDM and proposed an algorithm to match the toolpath with the extrusion speed so to eliminate voids and to correct overfill and underfill defects [3]. Pennington et al. conducted an experimental study to investigate factors significant to dimensional accuracy in FDM. The authors reported that the part size, the location and the envelope temperature have dominant effects [4]. Jiang and Gu also studied the extrusion phenomenon in FDM and reported that process parameters are critical to the part accuracy [5]. Reviewed, accepted September 14, 2006

Factors Analysis of Extruded Filament Width in FDM Molding Process

Variable Bead Width of Material Extrusion-Based Additive Manufacturing

The polymer melt swelling behavior in micro-extrusion process for preparation of continuous carbon fiber reinforced PP prepreg filament

A Parametric Study of Part Distortions in FDM Using 3D FEA

Material Extrusion Filament Width and Height Prediction via Design of Experiment and Machine Learning

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Quantitative Analysis of Surface Profile in Fused Deposition Modelling

Theoretical and Computational Analysis on the Melt Flow Behavior of Polylactic Acid in Material Extrusion Additive Manufacturing under Vibration Field

Fused Deposition Modelling (FDM) of Thermoplastic-Based Filaments: Process and Rheological Properties-An Overview

Modeling and self-supporting printing simulation of fuse filament fabrication

Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Finite Element Analysis of Warping and Mechanical Properties of 3D Parts Printed by Fused Deposition Modeling

Exit morphology and mechanical property of FDM printed PLA: influence of hot melt extrusion process

Numerical Simulation and Experimental Study Regarding the Cross-Sectional Morphology of PEEK Monofilament Deposition During FDM-Based 3D Printing

Numerical investigation on the viscoelastic polymer flow in material extrusion additive manufacturing

Analysis of the main factors affecting mass production in the plastic molding process by using the finite element method

Analysis of the Influencing Factors of FDM-Supported Positions for the Compressive Strength of Printing Components

Heritability of Fitness Components in a Wild Bird Population

Enhanced Dimensional Accuracy of Material Extrusion 3D-Printed Plastics through Filament Architecture

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone