Abstract:A detailed evaluation of the influence of variations in product (beef size and porosity) and process parameters (vacuum chamber pressure reduction rate) on cooling time, total mass loss, pressure and temperature distributions during the immersion vacuum cooling of large cooked beef joint samples was performed using a previously developed and validated mathematical model. Beef size variations were done by changing radius values (between 5.5 and 8 cm) and porosity levels (between 2 and 5%). Pressure reductions rates varied between circa 5 to 25 mbar/min. The simulation indicated that using the maximum pressure drop rate tested (circa 25 mbars/min) beef samples (3% porosity) of up to 6.5 and 7 cm radius can be cooled within Irish and American official safety guidelines, respectively. An increase in porosity could further reduce cooling time but incur higher mass losses, which can be detrimental to product quality. The identified effects and relevant trends due to variations on the different parameters studied on the cooling process performance lead to recommendations in relation to optimal pressure drop rate, in relation to size and porosity ranges. Necessary modifications to the equipment design, such as the introduction of agitation in the cooling medium, are also emphasised.Industrial relevance: Meat is typically cooked before consumption, and if it is not for immediate consumption, it should be cooled as soon as possible thereafter. Commercial products such as large cured and precooked meat pieces undergo heat treatment, and hence need to be cooled prior to packing, storage and distribution. Product temperature should be reduced as quickly as possible to its final target, to minimise quality loss and prevent or minimise microbial growth or spore germination. After relatively mild heat treatments such as pasteurisation (heat processes in the range of 60-80 degrees C) the microorganisms of concern are often heat resistant micro flora such as mesophilic spores of Bacillus and Clostridium species that under adequate conditions might germinate and grow, posing a safety risk. The difficulties of cooling large commercial meat pieces or joints have been reported, and the responsibility is on manufacturers to ensure that procedures are adequate and safety risks are minimised. Recent investigations into vacuum cooling have shown advances for the meat industry. (C) 2012 Elsevier Ltd. All rights reserved.

Effect of rapid and conventional cooling methods on the quality of cooked ham joints.

Preservation of Texture and Yield of Cooked Restructured Ham Using a Novel Rapid Cooling Method

Comparison of the Quality of Cooked Beef Products Cooled by Vacuum Cooling and by Conventional Cooling

Effect of Cooling Methods on Cooling Efficiency and Product Quality of Large Cooked Beef Products

Safety and Quality Evaluation of Large Meat Joints Cooled by a Precommercial Immersion Vacuum Cooling Prototype

EFFECTS OF COMBINED WATER COOKING–VACUUM COOLING WITH WATER ON PROCESSING TIME, MASS LOSS AND QUALITY OF LARGE PORK HAM

EXPERIMENTAL EVALUATION OF THE PERFORMANCE OF VACUUM COOLING METHOD FOR LARGE COOKED MEAT JOINTS

Feasibility Assessment of Vacuum Cooling of Cooked Pork Ham with Water Compared to That Without Water and with Air Blast Cooling

Experimental Investigation of Performance of Vacuum Cooling for Commercial Large Cooked Meat Joints

Effects of Processing Parameters on Immersion Vacuum Cooling Time and Physico-Chemical Properties of Pork Hams

Effect of combined vacuum cooling and air blast cooling on processing time and cooling loss of large cooked beef joints

Experimental Comparison of Cooling Commercial Large Cooked Meat Joints by Various Methods.

Application of immersion vacuum cooling to water-cooked beef joints – Quality and safety assessment

Evaluation of the Immersion Vacuum Cooling of Cooked Beef Joints—mathematical Simulation of Variations in Beef Size and Porosity and Pressure Reduction Rates

Effect of Vacuum Cooling on the Thermophysical Properties of a Cooked Beef Product

A Comparison of the Quality of Cooked Beef Cooled by Vacuum Cooling and by Conventional Cooling Differently

The Effect of Different Cooling Methods on the Quality of Whole Chicken

Effects of Different Cooling Methods on Shelf-Life of Cooked Jumbo Plain Sausages

Vacuum Cooling in Bulk of Beef Pieces of Different Sizes and Shape – Evaluation and Comparison to Conventional Cooling Methods

The effect of injection level on the quality of a rapid vacuum cooled cooked beef product

Heat transfer characteristics of cooked meats using different cooling methods