Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Optimization of parallel combustion numerical simulation—dynamic load balancing methods for adaptive unstructured meshes

Combustion Optimization Study of Pulverized Coal Boiler Based on Proximal Policy Optimization Algorithm

Numerical Methods for Complicated Chemical Mechanism Involved in Combustion Simulation

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Dynamic load balance of chemical source term evaluation in high-fidelity combustion simulations

Accurate and rapid reactive flow simulations using dynamic load balancing and sparse analytical Jacobian approach

Development of a Chemistry Dynamic Load Balancing Solver with Sparse Analytical Jacobian Approach for Rapid and Accurate Reactive Flow Simulations

Two-level parallel load balancing strategy for accelerating DSMC simulations in near-continuum gases

Increasing Computational Efficiency of CFD Simulations of Reactive Flows at Catalyst Surfaces through Dynamic Load Balancing

Multi-dimensional simulation of HCCI engine using parallel computation and chemical kinetics

Toward Efficient Chemistry Calculations in Engine Simulations Through Static Adaptive Acceleration

Numerical simulation of combustion and melting process in an aluminum melting Furnace: A study on optimizing stacking mode

A Sparse Stiff Chemistry Solver Based on Dynamic Adaptive Integration for Efficient Combustion Simulations

Parallel Implementation for Dynamic Mesh Optimization on Distributed Computer System.

Parallel Iterative Methods — Pipelined Iterative Methods on Combustion Problem

Multilevel Adaptive Methods for Turbulent Combustion with Detailed Chemistry: Part I

Application of the Projective Method in the Numerical Simulation of Combustion

Parallel Computation Technique for Mold Filling Simulation of Die Casting Process by Optimizing the Computational Parameters

Detailed numerical simulation of laminar flames by a parallel multiblock algorithm using loosely coupled computers

A novel online combustion optimization method for boiler combining dynamic modeling, multi-objective optimization and improved case-based reasoning

A Chemistry Load Balancing Model for OpenFOAM