Preparation and evaluation of glyceryl monooleate-coated hollow-bioadhesive microspheres for gastroretentive drug delivery.

Yuanfen Liu,Jianjun Zhang,Yuan Gao,Jiabi Zhu

DOI: https://doi.org/10.1016/j.ijpharm.2011.04.030

IF: 6.51

2011-01-01

International Journal of Pharmaceutics

Abstract:The hollow microsphere surface was initially coated with glyceryl monooleate (GMO). Then the microsphere was of good buoyancy and mucoadhesion.

What problem does this paper attempt to address?

Decoration and Application of PLGA Microspheres

FENG Shisen,WANG Wenxi,ZHENG Caihong

DOI: https://doi.org/10.13748/j.cnki.issn1007-7693.2016.06.040

2016-01-01

Abstract:Microspheres as novel drug delivery carriers have been widely used in clinical study, and poly lactic-co-glycolic acid (PLGA) has been one of the most attractive polymeric candidates used to fabricate devices for drug delivery due to the biocompatible and biodegradable characteristics. In recent years, in order to figure out the defects during the drug release, polymeric combination and chemical modification has been extensively studied. And the design of double-walled microspheres also has been investigated. Moreover, encapsulation efficiency and the release profiles can be improved by different modification methods. And it is extensively used in drug deliver, gene therapy and imaging diagnosis, especially in the fields of tissue engineering.
Preparation of Chlorogenic Acid Loaded Bioadhesive Microspheres and Its Release Profile in Vitro

Mei XIA,Ya-lan ZHANG,Jing-xuan GAO,Jiao ZHANG,Ying-ju HE

DOI: https://doi.org/10.13375/j.cnki.wcjps.2012.02.041

2012-01-01

Abstract:OBJECTIVE To prepare chlorogenic acid loaded bioadhesive microspheres and investigate its release profile in vitro and mucoadhesive characteristics.METHODS Chlorogenic acid loaded bioadhesive microspheres were prepared by solvent evaporation method.The formulations and the preparation methods were evaluated by single factor selecting experiment and the release profile.The drug release was analyzed by HPLC.Its mucoadhesive property was evaluated using stagnation percentage.RESULTS The average drug loading content and encapsulation efficiency of the optimum formulation of chlorogenic acid loaded bioadhesive microspheres were 17.25% and 57.25%.The microspheres could release 92.07% in vitro in 12 h.The release in vitro accorded to the Weibull order model:ln[ln[1/(1-Q)]]=0.6376lnt-0.4373(r=0.9819).The average stagnation percentage in vitro and vivo was 78.54% and 30.23%,respectively.CONCLUSION The preparation procedure was stable and practical,and the microspheres obtained showed a sustained-release character.
Progress of Gastrointestinal Retentive Microparticles System

FU Tian-Jiao,LIU Jian-Ping,JIN Fang

DOI: https://doi.org/10.3969/j.issn.1001-8255.2006.03.022

2006-01-01

Abstract:The profiles and evaluation methods of gastro-floating microballoons, bioadhesive liposomes and polymer microparticles are introduced. The progress of bioadhesive liposomes, microspheres and nanoparticles is emphasized.
Bioadhesive fluorescent microspheres as visible carriers for local delivery of drugs. I: preparation and characterization of insulin-loaded PCEFB/PLGA microspheres

H. L. Jiang,K. J. Zhu

DOI: https://doi.org/10.1080/02652040210141093

2008-01-01

Journal of Microencapsulation

Abstract:Inherently fluorescent microspheres composed of a flourescent polyanhydride, poly(p-(carboxyethylformamido) benzoic anhydride) (PCEFB), and poly(lactide-co-glycolide) (PLGA) were prepared using the water-in-oil-in-water (w/o/w) emulsion solvent evaporation technique. The effect of the PCEFB/PLGA feed ratio and composition of the oil phase on insulin entrapment and microsphere diameter was evaluated. It was found that the insulin entrapment efficiency increased with PCEFB content and acetone per cent in the oil phase. Microsphere diameter decreased as acetone was added into the oil phase. The blend of microspheres were further characterized by GPC, IR, fluorometry and SEM. Although slight degradation of PCEFB during the fabrication process was revealed by GPC and IR, PCEFB/PLGA microspheres could still be clearly visualized by either CLSM or fluorescent microscopy, which makes it possible to directly detect the microspheres by fluorometry in vivo without the need of labelling with fluorescent dyes. The surface of PCEFB/PLGA (1:2) microspheres was smooth, while PCEFB/PLGA (2:1) microspheres were observed with rough and uneven surfaces. Sustained release of insulin from the microspheres could be achieved for similar to4 days.
Preparation of Polysaccharide Microgels and Application in Sustained and Controlled Release Drug Delivery Systems

周琪,徐玉福,何红波,姚日生,邓胜松,何葆芳

DOI: https://doi.org/10.3969/j.issn.1003-5060.2009.02.013

2009-01-01

Abstract:Studies on polysaccharide microgels being used as the carrier for sustained and controlled drug delivery systems has become an important research field in polymeric science.In this paper,three kinds of polysaccharide microgels and their related application are reviewed.The physical method,chemical precipitation,reversed phase microemulsion,microemulsion-solvent volatilization and total aqueous phase method are used to synthesize polysaccharide microgels,including starch microgels,cellulose microgels and dextran microgels.The method of total aqueous phase without toxic solvents is the most promising way.The microgels show many advantages in drug sustained and controlled release,decreasing toxic,improving bioavailability in vivo,etc.Moreover,they are successively used to load and control the release of the medicine such as Insulin,Brufen,and so on.
A Novel Preparation Method for Microspheres by Glycerol Modified Solid‐in‐oil‐in‐water Multi‐emulsion

Weien Yuan,Tiantian Ren,Fei Wu,Hao Zhao,Tuo Jin

DOI: https://doi.org/10.1002/pat.1438

IF: 3.348

2009-01-01

Polymers for Advanced Technologies

Abstract:Biodegradable material poly(D, L-lactic-co-glycolic) acid (PLGA) plays an important role in drug-sustained release systems. Here, we describe a glycerol modified solid-in-oil-in-water (m-S/O/W) emulsion method for PLGA microspheres, in order to encapsulate proteins in PLGA by utilizing dextran glassy particles to protect the proteins from denaturing, unfolding, and aggregation during preparation and new external water phase to prevent the inner dextran glassy particles from leaking into the external water phase. External water phase containing 20, 40, 60, 80% glycerol showed that proteins released faster and more completely with increased glycerol content. According to their varied release profiles, microspheres of different formulations could be used to encapsulate vaccines or for delivering proteins over long-term. Copyright (C) 2009 John Wiley & Sons, Ltd.
Preparation and in Vitro Evaluation of Gelatin Microspheres for Embolization

Ya-Nan Wu,Wen-Jing Meng,Ying-Ying Liu,Tong Guo,Tian-Yuan Fan

DOI: https://doi.org/10.5246/jcps.2012.03.031

2012-01-01

Journal of Chinese Pharmaceutical Sciences

Abstract:The objective of this research was to develop gelatin microspheres (GMSs) and study their properties for embolization.The GMSs were prepared by emulsion chemical crosslinking method.The morphology and particle size of GMSs were observed under an optical microscope.The ratio of water absorption and GMSs swelling ratio were measured.The clasticity of GMSs was studied by TMS -Pro food texture analyzer.The deliverability ofGMSs through catheter was investigated with a new device designed in this study.Finally,the acetone residue was determined by headspace capillary gas chromatography.The dried GMSs were elliptic with corrugated surface and the wet GMSs were round with smooth surface.The average diameter of dried GMSs was 430.5 μm with a range of 100-1000 μm,and that of wet GMSs was 601.2 μm with a range of 150-1425 μm.The maximum ratio of water absorption was 590.7％ and the average swelling ratio was 103.0％.The elasticity of GMSs was proven to be appropriate for embolization.Three subgroups of wet GMSs (100-450 μm,450-700 μm and 700-940 μm) were delivered through catheter with acceptable pressure.The content of residual acetone in GMSs was less than the minimum limit in the Chinese Pharmacopoeia 2010.Therefore,we concluded that the GMSs were suitable for embolization according to the applicable properties in vitro.And the methods for assessing the properties of GMSs in this study were going to be useful in the evaluation of embolic microspheres.
Surface Fabrication of Hollow Microspheres from N-Methylated Chitosan Cross-Linked with Gultaraldehyde

XH Peng,L Zhang

DOI: https://doi.org/10.1021/la047689w

IF: 3.9

2004-01-01

Langmuir

Abstract:We have successfully prepared biocompatible and biodegradable hollow microspheres with sizes between 2 and 5 mum using cyclohexane droplets as a template and the N-methylated chitosan (NMC) cross-linked with glutaraldehyde (GA) as the shell. The structure, morphology, and formation process of the hollow microspheres were characterized by FT-IR, (1)H and (13)C NMR, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results revealed that the microspheres exhibited a very smooth and hollow structure. This work confirmed that the hollow microspheres were accomplished by fabricating on the basis of chemical cross-linking on the surface of the emulsion droplets and by removing cyclohexane as core. The results from SEM and TEM indicated that the emulsion droplets covered with cross-linked NMC in the oil-in-water system aggregated together to form a precipitate of microspheres by coagulating with acetone. Moreover, the cross-linked NMC on the surface of the microspheres continuously cured to form the tight shell, whereas the inner area became a cavity with increase of the aging time, leading to the hollow microspheres. In addition, an anti-infective drug, ofloxacin (Floxin), encapsulated in the microspheres more rapidly released to reach 90 wt % at pH 7.4 within 8 h than at pH 1.2.
Preparation and in Vitro Properties of Oleanolic Acid Hemiphthalate Disodium-Hydroxypropylmethylcellulose Acetate Succinate Microspheres

Jianbo Guo,Shaoning Wang,Yanyan Li,Xiaoyun Wang,Yanqiu Zhao,Hui Xu,Xing Tang

2009-01-01

Abstract:Purpose: To prepare oleanolic acid hemiphthalate disodium (OAHPDS)-hydroxypropylmethyl-cellulose acetate succinate (HPMCAS) microspheres and investigate their in vitro properties. Methods: The OAHPDS-HPMCAS microspheres were prepared by the emulsionsolvent evaporation method, and the in vitro drug release profiles of the microspheres were determined. DSC, XRPD, FTIR and SEM measurements were performed to characterize the physicochemical properties of the microspheres. Results: All the microspheres prepared exhibited perfect enteric dissolution. The XRPD results showed that the drug dispersed in the microspheres in the amorphous state. The DSC and FTIR measurements revealed the formation of hydrogen bonds between the drug and the polymer molecules. The initial drug/polymer ratio and the morphology (related to the evaporation pressure) of the microspheres may affect drug release profiles in acidic medium. Conclusion: Enteric OAHPDS-HPMCAS microspheres were prepared successfully by the emulsion-solvent evaporation method. The drug within microspheres played the role of “plasticizer”, becoming inserted between the glucose chains of HPMCAS and promoted the immigration of the glucose chain. The evaporation pressure affected the microsphere surface morphology and influenced the acidic release. The investigation revealed that HPMCAS microspheres can be used as an ideal carrier for the delayed release of drugs in the small intestine.
Mucoadhesivity Characterization of Isabgol Husk Mucilage Microspheres Crosslinked by Glutaraldehyde

Vipin Kumar Sharma,Prince Prashant Sharma,Bhasker Mazumder,Aseem Bhatnagar,Thakuri Singh

DOI: https://doi.org/10.2174/1567201812666150212124054

Abstract:The microspheres of Isabgol husk were prepared by emulsification-crosslinking technique and the gastrointestinal transition behavior of the formulation was studied by gamma scintigraphy. The impact of different process variables such as amount of glutaraldehyde, concentration of Isabgol husk and temperature was studied on surface morphology and mucoadhesion. In vitro mucoadhesive testing of formulations was performed by determination of zeta potential, mucus glycoprotein assay and mucus adsorption isotherms. The effect of feeding on retention of microspheres in the gastrointestinal track (GIT) was studied in albino rabbits by gamma scintigraphy study. The results indicated the formation of microspheres as observed by scanning electron microscopy. The smooth and round surfaces of microspheres were obtained on increasing Isabgol husk and glutaraldehyde amount. The positive zeta potential of all formulations indicated the electrostatic interaction as a mechanism of mucoadhesion between the mucus of GIT membranes and the microspheres surfaces. The influence of electrostatic interaction on mucoadhesion of microspheres was again ascertained when the mucin equilibrium adsorption on preparations indicated well fitness in Langmuir and Freundlich adsorption isotherms. During gamma scintigraphy, the stability of (99m)Tc-sodium pertechnetate was found 98.82% at pH 6.8 and 96.78% at pH 7.2, respectively. It indicated the minimal leaching of bound radionuclide from microspheres during gastrointestinal transition as observed in gamma scintigraphic images of the rabbits. The microspheres retained in GIT even after 24 hrs of oral administration. The results indicated the applicability of Isabgol husk mucilage in the development of mucoadhesive microspheres.
Prescription Optimization of Gastroretentive Furosemide Hollow-Bioadhesive Microspheres Via Box-Behnken Design: in Vitro Characterization and in Vivo Evaluation

Saige Meng,Shuangqing Wang,Ming Guan Piao

DOI: https://doi.org/10.1016/j.jddst.2022.103235

IF: 5

2022-01-01

Journal of Drug Delivery Science and Technology

Abstract:The synergistic gastroretentive drug delivery systems are capable of delivering drugs with a narrow absorption window. The purpose of this study is to prepare furosemide hollow-bioadhesive microspheres to improve bioavailability. The emulsion solvent volatilization method was adopted, through Box-Behnken design, with polymer ratio (X-1), dosage (X-2), organic solvent volume (X-3) and PVA concentration (X-4) as independent variables, and drug loading (Y-1), encapsulation rate (Y-2), yield rate (Y-3) and 8 h floating rate (Y-4) were response variables. The interaction effects of the independent and response variables were explored. The optimized hollow-bioadhesive microspheres showed the in vitro floating rate of 93.33 +/- 5.24% for 8 h, the in vitro retention rate of 90.67 +/- 3.21%, and the sustained drug release of 93.79 +/- 4.90% for 12 h. Compared with the hollow microspheres, the hollow-bioadhesive microspheres significantly increase the retention time in the stomach. The results of Differential Scanning Calorimetry, Fourier Transform InfraRed, and X-ray diffraction showed that furosemide had good biocompatibility with excipients. Compared with commercial tablets, the relative bioavailability of hollow-bioadhesive microspheres was increased by 163.84%, and the long-term therapeutic concentration was maintained. The safety evaluation proved the oral safety of microspheres. In conclusion, the safe and economical furosemide hollow-bioadhesive microsphere is a valuable preparation for development, which can improve clinical application.
[Preparation and Physicochemical Characterization of Hydrogel Microspheres for Embolization].

Chao Zhou,Yan-fei Zhou,Tian-yuan Fan

DOI: https://doi.org/10.3321/j.issn:1671-167x.2007.02.016

2007-01-01

Abstract:OBJECTIVE:To develop and characterize the hydrogel microspheres for embolization.METHODS:N-[tris (hydroxymethyl) methyl] acrylamide-gelatin microspheres (TGMs) were prepared by an inverse suspension polymerization approach. Effects of materials on size, water absorption rate and elasticity of the microspheres were investigated. The materials which were included consisted of gelatin in the range of 10.0-100.0 g/L, N-[tris (hydroxymethyl)methyl]acrylamide in the range of 33.3-200 g/L, cross-linking agent N,N'-methylene-bis-acrylamide in the range of 3.3-10.0 g/L, surfactant Span 80 in the range of 0.5-1.8 g/L, and initiator ammonium persulfate in the range of 1.0-5.0 g/L. The appearance of TGMs was observed under microscope. TGMs were analyzed by infrared spectrum (IR).RESULTS:The TGMs were round with smooth surface in view of photograph of microscope. The average diameter of TGMs was increased with the increase of gelatin, monomer or cross-linking agent concentrations but decreased with the increase of surfactant or initiator Concentration. The water adsorption rate of the microspheres was decreased with the increase of gelatin or cross-linking agent concentration but not affected by surfactant concentration. The elasticity of TGMs was increased with the increase of monomer or cross-linking agent concentration, decreased with the increase of gelatin concentration, but not affected by surfactant or initiator concentration. All factors above considered, the final prepared TGMs consisted of 10 g/L gelatin, 100.0 g/L monomer, 6.7 g/L cross-linking agent, 0.9 g/L surfactant, and 3.0 g/L initiator. The average diameter of TGMs obtained was about 700.0 microm. The water adsorption rate and the elasticity in accordance with the maximum diameter of the microspheres passed through a microcatheter of TGMs were 12.4 (g/g), and 1 600.0 microm, respectively. The results of IR spectra confirmed the polymerization of monomer, resulting in Nj[tris(hydroxymethyl)methyl]acrylamidegelatin microspheres.CONCLUSION:The developed TGMs seemed to be suitable for clinical embolization according to the surface, average diameter, elastic and hydrophilic property of TGMs.
Development and Evaluation of a New Gastroretentive Drug Delivery System: Nanomicelles-loaded Floating Mucoadhesive Beads

Nana Chen,Jing'e Niu,Qian Li,Jianyin Li,Xinping Chen,Yuan Ren,Guotai Wu,Yingqian Liu,Yanbin Shi

DOI: https://doi.org/10.1016/j.jddst.2019.03.024

IF: 5

2019-01-01

Journal of Drug Delivery Science and Technology

Abstract:To better treat gastric diseases and lower systemic side effect, it is essential to design new vectors to control drug release in stomach. Aiming to this challenge, we developed a new gastroretentive drug delivery system: nanomicelles-loaded gastroretentive beads. Firstly, the chitosan-coated emodin-loaded nanomicelles were developed and characterized. In vitro cytotoxicity of emodin-loaded nanomicelles, emodin suspensions and blank nanomicelles was evaluated with human gastric carcinoma SGC-7901 cells by MTT, indicating that the blank nanomicelles had null cytotoxicity and emodin-loaded nanomicelles had better antitumor efficacy compared with emodin suspensions. Secondly, nanomicelles-loaded floating mucoadhesive beads (NFM-Beads) were prepared, and the swelling, degradation, mucoadhesion and floating ability in vitro were separately investigated. FT-IR spectroscopy was applied to identify the formation of nanomicelles and NFM-Beads. Emodin release from NFM-Beads in vitro was fitted to anomalous transport mechanism. In vivo gastroretention behavior of NFM-Beads was evaluated by BaSO4-based X-ray imaging exams, showing that NFM-Beads can be retained in rabbit stomach for at least 8 h. Overall, the new NFM-Beads system could be an effective approach to improve the therapeutic potency of drug against gastric cancer.
Controllable preparation of bioactive open porous microspheres for tissue engineering

Anqi Lin,Shengyang Liu,Lan Xiao,Yingying Fu,Changsheng Liu,Yulin Li

DOI: https://doi.org/10.1039/d2tb01198k

IF: 7.571

2022-01-01

Journal of Materials Chemistry B

Abstract:Biodegradable microspheres have been widely applied as cell carriers for tissue engineering and regenerative medicine. However, most cell carriers only have a simple planar structure and show poor biological activity and cell adherence, resulting in low cell density and unfavorable application effect. How to develop size-controllable microspheres with an open-porous structure remains a challenge, and is a key factor to extend their employment as cell/drug delivery vehicles to boost regeneration of tissues (e.g., bone). Herein, well-defined open porous microspheres of poly(lactic-co-glycolic acid) (PLGA with good biocompatibility approved by the Food and Drug Administration (FDA)) were developed by using a gas-assisted-emulsion and surface-alkalization-treatment technology (GEST). The gas-assisted-emulsion strategy enables the formation of microspheres with a large size of 200-300 mu m, meanwhile, the microspheres have a large amount of micropores with diameter in the range of 10-60 mu m. The following alkalization-treatment on the surface makes the microspheres form a good porous interconnectivity throughout both the surface and the interior of the microspheres. The good porous interconnectivity endows the microspheres with a highly open pore structure and a large specific surface area for nutrient exchange and cell attachment, thus promoting cell proliferation and nutrient transportation, promising their potential as an ideal cell carrier to increase cell density and bioactivity for cell therapy-based tissue engineering.
Preparation and characterization of novel multi-core chitosan microspheres for stomach-specific delivery of hydrophilic antibiotics

Xi Zhu,Dan Zhou,Shan Guan,Peiwen Zhang,Zhirong Zhang,Yuan Huang

DOI: https://doi.org/10.1007/s10856-012-4567-9

2012-01-01

Abstract:Insufficient gastric mucosa drug concentration and short contact time were the main reason for the lack of eradication efficacy of Helicobacter pylori for peptic ulcer patients. Novel multi-core chitosan microspheres were prepared for stomach-specific delivery of hydrophilic antibiotics for the treatment of peptic ulcer. Chitosan microspheres with multiple Eudragit L100 cores were easily prepared by a new emulsification/coagulation encapsulating method. Swelling behaviors, surface amino groups and mucin absorption ability were investigated and the formulation that showed best mucoadhesive potential was adopted. The multi-core chitosan microspheres exhibited good mucoadhesiveness as well as controlled release manner for incorporated antibiotics in acidic environment. The release rate could be easily modulated with accumulative release ranging from 47.3 to 79.3% in 6 h. Accordingly, the multi-core chitosan microspheres could serve as a satisfactory vehicle for stomach-specific delivery of hydrophilic antibiotics.
Novel Preparation Method for Sustained-Release Plga Microspheres Using Water-In-Oil-In-Hydrophilic-Oil-In-Water Emulsion

Xiaoyun Hong,Liangming Wei,Liuqing Ma,Yinghui Chen,Zhenguo Liu,Weien Yuan

DOI: https://doi.org/10.2147/ijn.s45186

IF: 7.033

2013-01-01

International Journal of Nanomedicine

Abstract:An increasing number of drugs are needing improved formulations to optimize patient compliance because of their short half-lives in blood. Sustained-release formulations of drugs are often required for long-term efficacy, and microspheres are among the most popular ones. When drugs are encapsulated into microsphere formulations, different methods of preparation need to be used according to specific clinical requirements and the differing physicochemical characteristics of individual drugs. In this work, we developed a novel method for sustained-release drug delivery using a water-in-oil-in-hydrophilic oil-in-water (w/o/oh/w) emulsion to encapsulate a drug into poly(lactic-co-glycolic acid) (PLGA) microspheres. Different effects were achieved by varying the proportions and concentrations of hydrophilic oil and PLGA. Scanning electron and optical microscopic images showed the surfaces of the microspheres to be smooth and that their morphology was spherical. Microspheres prepared using the w/o/oh/w emulsion were able to load protein efficiently and had sustained-release properties. These results indicate that the above-mentioned method might be useful for developing sustained-release microsphere formulations in the future.
Preparation and characterization of novel biodegradable multifunctional microspheres

Xiaofei Liang,Hanjie Wang,Hao Luo,Hui Tian,Min Zhi,YongLan Wang,Jin Chang

DOI: https://doi.org/10.3321/j.issn:0567-7351.2008.19.016

2008-01-01

Acta Chimica Sinica

Abstract:Octadecyl quaternized carboxymethyl chitosan (OQCMC) was synthesized through carboxymethyl chitosan grafting with glycidyl octadecyl dimethylammonium chloride. By a solvent evaporation method, the drug delivery system was prepared based on poly(lactic-co-glycolic acid) (PLGA) block copolymers, hydroxyethyl cellulose and OQCMC, which was tried to load minocycline hydrochloride. The microspheres were characterized by transmission electron microscopy (TEM), quasielastic laser light scattering with a Malvern Zetasizer, 1H NMR and FTIR. The results showed that the complex delivery system was good to load the minocycline hydrochloride and could provide long-term release behaviour through drug release experiment in vitro. The drug loading efficiency of minocycline hydrochloride could reach 9.4% by using the polymer surfactant OQCMC. It is good to decrease the particle size [(166.4±0.8) nm], increase the Zeta potential and keep the stabilization of the microspheres.
Mucoadhesive and Rheological Studies on the Co-Hydrogel Systems of Poly(Ethylene Glycol) Copolymers with Fluoroalkyl and Poly(Acrylic Acid)

Yang Sun,Adiel F Perez,Ivy L Cardoza,Nina Baluyot-Reyes,Yong Ba,Adiel F. Perez,Ivy L. Cardoza

DOI: https://doi.org/10.3390/polym13121956

IF: 5

2021-06-12

Polymers

Abstract:A self-assembled co-hydrogel system with sol-gel two-phase coexistence and mucoadhesive properties was developed based on the combined properties of fluoroalkyl double-ended poly(ethylene glycol) (Rf-PEG-Rf) and poly(acrylic acid) (PAA), respectively. We have synthesized an Rf-PEG-g-PAA (where g denotes grafted) copolymer and integrated it into the Rf-PEG-Rf physically cross-linked micellar network to form a co-hydrogel system. Tensile strengths between the co-hydrogel surfaces and two different sets of mucosal surfaces were acquired. One mucosal surface was made of porcine stomach mucin Type II, while the other one is a pig small intestine. The experimental results show that the largest maximum detachment stresses (MDSs) were obtained when the Rf-PEG-g-PAA’s weight percent in the dehydrated polymer mixture is ~15%. Tensile experiments also found that MDSs are greater in acidic conditions (pH = 4–5) (123.3 g/cm2 for the artificial mucus, and 43.0 g/cm2 for pig small intestine) and basic conditions (pH = 10.6) (126.9 g/cm2, and 44.6 g.cm2, respectively) than in neutral pH (45.4 g/cm2, and 30.7 g.cm2, respectively). Results of the rheological analyses using shear strain amplitude sweep and frequency sweep reveal that the Rf-PEG-g-PAA was physically integrated into the Rf-PEG-Rf micellar network, and the co-hydrogels remain physically cross-linked in three-dimensional micellar networks with long-term physical dispersion stability. Therefore, the co-hydrogel system is promising for drug delivery applications on mucosal surfaces.

polymer science
Preparation Of Monodisperse Biodegradable Polylactic Acid Microspheres Using A Simple Microfluidic Approach

He Tianxi,Liang Qionglin,Wang Yiming,Luo Guoan

2009-01-01

Abstract:Biodegradable and biocompatibility polymeric microspheres have wide applications in many fields, especially as carriers for drug delivery and form the basis of several therapies approved by the US Food and Drug Administration. This paper describes the preparation controllable and monodisperse microspheres from biodegradable and biocompatibility polylactic acid (PLA) using a single microfluidic approach. We have demonstrated that one could control the size of microspheres from 15 mu m to 150 mu m in size (polydispersity index < 5%) by altering the relative sheath/sample flow rate ratio. Polylactic acid microspheres are ideally potential carrier for drug delivery.
Spray-dried mucoadhesive microspheres: Preparation and transport through nasal cell monolayer

Saraporn Harikarnpakdee,Vimolmas Lipipun,Narueporn Sutanthavibul,Garnpimol C Ritthidej

DOI: https://doi.org/10.1208/pt070112

IF: 3.3

AAPS PharmSciTech

Abstract:The purpose of this research was to prepare spray-dried mucoadhesive microspheres for nasal delivery. Microspheres composed of hydroxypropyl methylcellulose (H), chitosan (CS), carbopol 934P (CP) and various combinations of these mucoadhesive polymers, and maltodextrin (M), colloidal silicon dioxide (A), and propylene glycol (P) as filler and shaper, were prepared by spray-drying technique. Using propranolol HCl as a model drug, microspheres were prepared at loadings exceedings 80% and yields between 24% and 74%. Bulky, free flowing microspheres that had median particle size between 15 and 23 μm were obtained. Their zeta potential was according to the charge of polymer. Adhesion time of mucoadhesive microspheres on isolated pig intestine was ranked, CS>CP: H>CP>H, while the rank order of swelling was CP>CS>H. Increasing the amount of CP in CP∶H formulations increased the percentage of swelling. Infrared (IR) spectra showed no interaction between excipients used except CS with acetic acid. The release of drug from CP and CP∶H microspheres was slower than the release from H and CS microspheres, correlated to their viscosity and swelling. Long lag time from the CP microspheres could be shortened when combined with H. The permeation of drug through nasal cell monolayer corresponded to their release profiles. These microspheres affected the integrity of tight junctions, relative to their swelling and charge of polymer. Cell viability was not affected except from CS microspheres, but recovery could be obtained. In conclusion, spray-dried microspheres of H, CS, CP, and CP∶H could be prepared to deliver drug through nasal cell monolayer via the opening of tight junction without cell damaging.

Preparation and evaluation of glyceryl monooleate-coated hollow-bioadhesive microspheres for gastroretentive drug delivery.

Decoration and Application of PLGA Microspheres

Preparation of Chlorogenic Acid Loaded Bioadhesive Microspheres and Its Release Profile in Vitro

Progress of Gastrointestinal Retentive Microparticles System

Bioadhesive fluorescent microspheres as visible carriers for local delivery of drugs. I: preparation and characterization of insulin-loaded PCEFB/PLGA microspheres

Preparation of Polysaccharide Microgels and Application in Sustained and Controlled Release Drug Delivery Systems

A Novel Preparation Method for Microspheres by Glycerol Modified Solid‐in‐oil‐in‐water Multi‐emulsion

Preparation and in Vitro Evaluation of Gelatin Microspheres for Embolization

Surface Fabrication of Hollow Microspheres from N-Methylated Chitosan Cross-Linked with Gultaraldehyde

Preparation and in Vitro Properties of Oleanolic Acid Hemiphthalate Disodium-Hydroxypropylmethylcellulose Acetate Succinate Microspheres

Mucoadhesivity Characterization of Isabgol Husk Mucilage Microspheres Crosslinked by Glutaraldehyde

Prescription Optimization of Gastroretentive Furosemide Hollow-Bioadhesive Microspheres Via Box-Behnken Design: in Vitro Characterization and in Vivo Evaluation

[Preparation and Physicochemical Characterization of Hydrogel Microspheres for Embolization].

Development and Evaluation of a New Gastroretentive Drug Delivery System: Nanomicelles-loaded Floating Mucoadhesive Beads

Controllable preparation of bioactive open porous microspheres for tissue engineering

Preparation and characterization of novel multi-core chitosan microspheres for stomach-specific delivery of hydrophilic antibiotics

Novel Preparation Method for Sustained-Release Plga Microspheres Using Water-In-Oil-In-Hydrophilic-Oil-In-Water Emulsion

Preparation and characterization of novel biodegradable multifunctional microspheres

Mucoadhesive and Rheological Studies on the Co-Hydrogel Systems of Poly(Ethylene Glycol) Copolymers with Fluoroalkyl and Poly(Acrylic Acid)

Preparation Of Monodisperse Biodegradable Polylactic Acid Microspheres Using A Simple Microfluidic Approach

Spray-dried mucoadhesive microspheres: Preparation and transport through nasal cell monolayer