Removal of Heavy Metal Ions from Wastewater by Sugarcane Bagasse as Adsorbent

Xiong Bailian,Zhang Jinzhong,Xing Ze

DOI: https://doi.org/10.3969/j.issn.1008-9500.2008.08.011

2008-01-01

Abstract:In this paper, the progress of removing of heavy metal ions from wastewater using sugarcane bagasse and its derivants was summarized. The modified methods, principles and main influence factors were introduced,and the prospect was forecasted.

What problem does this paper attempt to address?

Changes in the Extractability and Fractionation of Cadmium and Copper in a Contaminated Soil Amended with Various Sugarcane Bagasse-Based Materials

Guofei Liu,Lingfei Hu,Caixian Tang,Jianming Xu

DOI: https://doi.org/10.1016/j.ecoenv.2024.116443

IF: 7.129

2024-01-01

Ecotoxicology and Environmental Safety

Abstract:Heavy-metal contamination in soil has long been a persistent challenge and the utilization of agricultural waste for in-situ stabilization remediation presents a promising approach to tackle this problem. Agricultural wastes exhibit promising potential in the remediation of contaminated land and modification could improve the adsorption performance markedly. Citric acid and Fe3O4 treated sugarcane bagasse adsorbed more heavy metals than raw materials in the aqueous system, employing these materials for heavy metal remediation in soil holds significant implications for broadening the raw material source of passivators and enhancing waste utilization efficiency. In this paper, a 120-day soil incubation study was conducted to compare the effects of pristine sugarcane bagasse (SB), citric-acid modified (SSB1, SSB2 and SSB3 with increasing proportion of citric acid) and citric-acid/Fe3O4 modified (MSB1, MSB4 and MSB7 with increasing proportion of Fe3O4) sugarcane bagasse at 1 % addition rate on cadmium (Cd) and copper (Cu) passivation. The SB, SSB1 and MSB1 did not always decrease the content of CaCl2-extractable Cd while all the seven amendments decreased the CaCl2-extractable Cu during the experiment period. Among all materials, SSB3 and MSB7 exhibited the highest efficiency in reducing the concentrations of CaCl2-extractable Cd and Cu. At Day 120, SB, SSB3 and MSB7 reduced the content of CaCl2-extractable Cd by 8 %, 18 % and 24 %, and of CaCl2-extractable Cu by 25 %, 50 % and 61 %, respectively. The efficiency of Cd and Cu immobilization was associated positively with the pH, functional groups and H-bonds of the amendments. The results suggest that the efficiency of sugarcane bagasse in heavy-metal passivation can be largely enhanced through chemical modifications using high proportions of citric acid and Fe3O4.
A Review on the Mitigation of Heavy Metals from Aqueous Solution using Sugarcane Bagasse

Kingsley O. Iwuozor,Ifeoluwa Peter Oyekunle,Iyiola Olatunji Oladunjoye,Enoch Mayowa Ibitogbe,Temidayo Samuel Olorunfemi

DOI: https://doi.org/10.1007/s12355-021-01051-w

2021-10-15

Sugar Tech

Abstract:Man's battle against pollutants in his quest for clean water and a cleaner environment has been justified to be beneficial not just to himself but also to every other animal. One of such pollutants is the heavy metals which are non-biodegradable and through their bioaccumulation in living tissues can cause mild to severe breakdown in living organisms. This review centers on the removal of these heavy metals from aqueous solution using a very cheap and readily available agricultural waste—Sugarcane Bagasse. In this research, the effect of the various modifications on sugarcane bagasse through their maximum adsorption capacities, isotherms, kinetic models, mechanism of adsorption and thermodynamic models were studied. It was observed that modification significantly improved the adsorption capacity of the sugarcane bagasse and the maximum sorption capacity recorded for Cu(II), Cd(II), Cr(III), Cr(VI), Ni(II), Pb(II), and Zn(II) were 268.0 mg/g, 320.0 mg/g, 82.99 mg/g, 3.956 mg/g, 167.0 mg/g, 700.0 mg/g, and 200.0 mg/g, respectively, all of which were modified sugarcane bagasse except for Cr(VI). It was observed that the adsorption mechanism was mostly due to electrostatic interaction and ion exchange and the best fit isotherm was mostly Langmuir or Freundlich and pseudo-second-order kinetic model was the best-fit kinetic model in most cases. Some research gaps were also stated to aid future researches as sugarcane bagasse has shown to be a very promising bio-adsorbent for the adsorption of heavy metals.

agronomy
Advances in Research on Treatment of Heavy Metal Ions Wastewater by Agricultural Waste

Li Lingxiangyu,Wu Jianyang,Tian Guangming,Xu Zhenlan

DOI: https://doi.org/10.3969/j.issn.1003-188X.2009.09.063

2009-01-01

Abstract:Agricultural waste was used for heavy metal ions removal from wastewater.It was considered as a new method for treatment of heavy metal ions in wastewater.Its major advantages over conventional treatment methods included:low cost,high efficiency and regeneration of biosorption.This paper summarized studies on heavy metal ions removal from wastewater using various agricultural waste in recent years,especially underscored the mechanism and models,and several heavy metals removal,like Pb,Cd,Ni,Cu,Zn,Mn and Hg,in order to provide theoretical guidance of using agricultural waste for removal heavy metal ions from wastewater.
Recent Progress on the Adsorption of Heavy Metal Ions Pb(II) and Cu(II) from Wastewater

Dikang Fan,Yang Peng,Xi He,Jing Ouyang,Liangjie Fu,Huaming Yang

DOI: https://doi.org/10.3390/nano14121037

2024-06-16

Abstract:With the processes of industrialization and urbanization, heavy metal ion pollution has become a thorny problem in water systems. Among the various technologies developed for the removal of heavy metal ions, the adsorption method is widely studied by researchers and various nanomaterials with good adsorption performances have been prepared during the past decades. In this paper, a variety of novel nanomaterials with excellent adsorption performances for Pb(II) and Cu(II) reported in recent years are reviewed, such as carbon-based materials, clay mineral materials, zero-valent iron and their derivatives, MOFs, nanocomposites, etc. The novel nanomaterials with extremely high adsorption capacity, selectivity and particular nanostructures are summarized and introduced, along with their advantages and disadvantages. And, some future research priorities for the treatment of wastewater are also prospected.
Synthesis of Cellulose–Poly(Acrylic Acid) Using Sugarcane Bagasse Extracted Cellulose Fibres for the Removal of Heavy Metal Ions

Fuchao Li,Zhemin Xie,Jianfeng Wen,Tao Tang,Li Jiang,Guanghui Hu,Ming Li

DOI: https://doi.org/10.3390/ijms24108922

IF: 5.6

2023-05-18

International Journal of Molecular Sciences

Abstract:In this study, sugarcane bagasse (SCB) was treated with sodium hydroxide and bleached to separate the non-cellulose components to obtain cellulose (CE) fibres. Cross-linked cellulose–poly(sodium acrylic acid) hydrogel (CE–PAANa) was successfully synthesised via simple free-radical graft-polymerisation to remove heavy metal ions. The structure and morphology of the hydrogel display an open interconnected porous structure on the surface of the hydrogel. Various factors influencing batch adsorption capacity, including pH, contact time, and solution concentration, were investigated. The results showed that the adsorption kinetics were in good agreement with the pseudo-second-order kinetic model and that the adsorption isotherms followed the Langmuir model. The maximum adsorption capacities calculated by the Langmuir model are 106.3, 333.3, and 163.9 mg/g for Cu(II), Pb(II), and Cd(II), respectively. Furthermore, X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectrometry (EDS) results demonstrated that cationic exchange and electrostatic interaction were the main heavy metal ions adsorption mechanisms. These results demonstrate that CE–PAANa graft copolymer sorbents from cellulose-rich SCB can potentially be used for the removal of heavy metal ions.

biochemistry & molecular biology,chemistry, multidisciplinary
Adsorption of heavy metal ions by iron tailings: Behavior, mechanism, evaluation and new perspectives

Chenglong Xu,Yali Feng,Haoran Li,Ruifeng Wu,Jinrong Ju,Shunliang Liu,Yi Yang,Ben Wang

DOI: https://doi.org/10.1016/j.jclepro.2022.131065

IF: 11.1

2022-04-01

Journal of Cleaner Production

Abstract:Here we report the adsorption of heavy metal ions from wastewater by the pellet material () of iron tailings (IT) compounded with sodium alginate (SA) as a regenerable adsorbent. The adsorption capacities of on Zn2+, Cu2+, Pb2+ and Ni2+ were 1.748 mg/g, 2.404 mg/g, 10.000 mg/g and 1.279 mg/g, respectively. The adsorption behavior would be in accordance with the Langmiur isothermal adsorption model, the pseudo-second-order kinetic model and the intra-particle diffusion model, indicating that the adsorption process was mainly controlled by monolayer chemisorption on heterogeneous surfaces, and that the adsorption proceeded spontaneously due to intermolecular interactions. The selective adsorption of can be represented as exhibited Pb2+ > Cu2+ > Zn2+ > Ni2+ under competitive adsorption conditions. The adsorption mechanisms mainly include surface physical adsorption, ion exchange, functional group complexation, precipitation, electrostatic attraction, etc. This work opens up a new direction for designing stimuli-responsive materials for energy-efficient and sustainable heavy metal ions adsorption and water purification, while the recycling of iron tailings contributes to the sustainable development of China's iron ore processing industry. It fully conforms to the concept of clean production and efficient utilization of industrial solid waste materials.

environmental sciences,green & sustainable science & technology,engineering, environmental
Rotten sugarcane bagasse derived biochars with rich mineral residues for effective Pb (II) removal in wastewater and the tech-economic analysis

Xingang Bai,Mengmeng Zhang,BingXuan Niu,Wenlong Zhang,Xiaopeng Wang,Jinshui Wang,Dapeng Wu,Le Wang,Kai Jiang,Bingxuan Niu

DOI: https://doi.org/10.1016/j.jtice.2022.104231

IF: 5.477

2022-03-01

Journal of the Taiwan Institute of Chemical Engineers

Abstract:Background Bio-waste derived biochars represent a group of low-cost and effective materials to achieve the removal of the heavy metal ions from polluted water bodies. Methods Rotten sugarcane bagasse was firstly adopted as raw material to prepare low cost biochars based on a molten salt method for the heavy metal ion removal. Significant findings The optimized rotten sugarcane bagasse derived biochars (RB-C) demonstrates maximum Pb2+ adsorption capacity of 339 mg g−1, which is greatly enhanced from the bio-chars prepared from fresh bagasse (172 mg g−1). In addition, the RB-C shows high efficiency for the treatment of the simulated wastewater with multiple metal ions. Based on the mechanism studies, these improved absorption performances are possibly derived from the surface physical sorption and static electron interaction due to the enhanced specific surface area (391.9 m2 g−1), increased pore diameter (20.9 nm) and well-developed hierarchical porous structure. Moreover, the RB-C exhibits rich mineral contents, which could further enhance the adsorption performances taking advantage of the ion exchange. In addition, the tech-economic assessment indicated the cost of RB-C ($ 2.39 kg−1) is comparable with the commercial active carbon, which endows rotten bagasse a abundant raw material to prepare low cost adsorbent with high performance to remove heavy metal ions from aquatic environment.

engineering, chemical
Organic Adsorbents Modified with Citric Acid and Fe3O4 Enhance the Removal of Cd and Pb in Contaminated Solutions

Guofei Liu,Liang Liao,Zhongmin Dai,Qian Qi,Jizi Wu,Lena Q. Ma,Caixian Tang,Jianming Xu

DOI: https://doi.org/10.1016/j.cej.2020.125108

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:Environmentally-friendly organic adsorbents with strong stability, magnetic property and great adsorption capacity for heavy metals have obtained great attention recently. We developed the citric acid- and Fe3O4-modified sugarcane bagasse (MSB) to investigate its behaviors and mechanisms of Cd and Pb adsorption in aqueous systems in comparison with sugarcane bagasse (SB). The MSB showed the highest adsorption capacity of 33.2 mg g(-1) for Cd and 116.7 mg g(-1) for Pb, which was mainly attributed to its O-containing functional groups (e.g. hydroxyl and carboxyl) and aromatic rings. In the binary system, Pb significantly suppressed the adsorption of Cd by MSB whereas Cd had weak inhibitive effects on Pb adsorption. The presence of Ca and Mg competed with the Cd and Pb for adsorption sites and their competition was stronger for Cd than Pb. Furthermore, MSB was easily regenerated and reused for three cycles with a higher adsorption capacity compared with SB. These findings provide new insights for development of novel adsorbents to remove heavy metals in aqueous systems.
Application of biomass adsorbents in the treatment of heavy metals in wastewater: a review

Junyue Shan,Caifang Li,Zhenming Zhang,Jiachun Zhang,Xingfu Wang,Xianfei Huang

DOI: https://doi.org/10.5004/dwt.2022.28691

IF: 1.1

2022-01-01

Desalination and Water Treatment

Abstract:In recent years, heavy metal pollution has become an increasingly serious problem, and various remediation technologies are progressing and breaking through. Biomass is the most widespread and most abundant substance on earth, and it has low cost and good environmental compatibility. The adsorption materials prepared from biomass as a raw material have high removal rates, green environmental protection, degradability, large specific surface area and high porosity. This article reviews the research progress of biomass adsorption materials in heavy metal wastewater treatment. First, we elucidate the basic types of biomass materials, the common preparation and modification methods, and the main mechanisms of biomass materials in adsorption. Second, the application of various biomass adsorption materials in heavy metal pollution treatment is highlighted, and we also summarize the main factors affecting the biomass adsorption process. Finally, there are still many problems with biomass adsorption materials, and biomass adsorption materials with high recovery rates, good selection performance and mass production are not yet available. More extensive and comprehensive research is urgently needed.

engineering, chemical,water resources
Research progress on chemical modification of waste biomass cellulose to prepare heavy metal adsorbents

Yuwei Yuan,Ruyan Li,Shengjuan Peng

DOI: https://doi.org/10.1007/s00289-022-04568-6

IF: 2.843

2022-12-21

Polymer Bulletin

Abstract:Heavy metal ions in water are harmful to the environment and the human body. How to remove them is a current research hotspot. Adsorption is currently the most economical and effective method for removing heavy metal pollution from water. Among the adsorbent materials used in adsorption methods, biomass materials have attracted much attention because of their wide sources, good adsorption capacity, and favorable carbon emission reduction. This paper summarizes the utilization of waste biomass cellulose-based adsorbents in the field of heavy metal adsorption and discusses various chemical modification methods such as oxidation, etherification, esterification, graft copolymerization, and composite modification of cellulose based on pretreatment. The modification process, modification effect, and application characteristics of different chemical modification methods were summarized and analyzed from the aspects of molecular structure, surface groups, and adsorption mechanism of cellulose. The changes of the adsorption properties of cellulose materials under different modification methods were compared, and the effects of external factors such as ionic radius and solution environment on the adsorption effect were also discussed. Finally, the development prospect of waste biomass cellulose material is discussed, the problems existing when the material is used as adsorbent are analyzed, and the adsorption performance in complex environments and the plans to further improve the adsorption performance are prospected.

polymer science
Recent progress in electrospun nanofibers and their applications in heavy metal wastewater treatment

Xizi Xu,He Lv,Mingxin Zhang,Menglong Wang,Yangjian Zhou,Yanan Liu,Deng-Guang Yu

DOI: https://doi.org/10.1007/s11705-022-2245-0

IF: 4.803

2023-01-04

Frontiers of Chemical Science and Engineering

Abstract:Novel adsorbents with a simple preparation process and large capacity for removing highly toxic and nondegradable heavy metals from water have drawn the attention of researchers. Electrospun nanofiber membranes usually have the advantages of large specific surface areas and high porosity and allowing flexible control and easy functionalization. These membranes show remarkable application potential in the field of heavy metal wastewater treatment. In this paper, the electrospinning technologies, process types, and the structures and types of nanofibers that can be prepared are reviewed, and the relationships among process, structure and properties are discussed. On one hand, based on the different components of electrospun nanofibers, the use of organic, inorganic and organic-inorganic nanofiber membrane adsorbents in heavy metal wastewater treatment are introduced, and their advantages and future development are summarized and prospected. On the other hand, based on the microstructure and overall structure of the nanofiber membrane, the recent progresses of electrospun functional membranes for heavy metal removal are reviewed, and the advantages of different structures for applications are concluded. Overall, this study lays the foundation for future research aiming to provide more novel structured adsorbents.

engineering, chemical
Removal of heavy metals from wastewater using agricultural byproducts

Hayder A. Alalwan,Mohammed A. Kadhom,Alaa H. Alminshid

DOI: https://doi.org/10.2166/aqua.2020.133

2020-02-19

Abstract:Abstract The use of agricultural waste to remove heavy metals from wastewater has attracted much attention due to its economic advantages and high removal efficiency which is attributed to different functional groups. The sorption mechanism of biomass can consist of several steps including chemisorption, complexation, adsorption on surface, diffusion through pores, and ion exchange. Heavy metals were removed in different rates depending on the adsorbent and metal itself. For instance, coconut waste showed adsorption capacities of 263 and 285 mg/g in removing lead and cadmium ions, respectively. Also, black oak bark has adsorbed mercury in an adsorption capacity of 400 mg/g, while wheat brans adsorption capacity for chromium was 310 mg/g. The adsorption capacity is commonly calculated by Lagergren's first-order equation, the Redlich Peterson model, and the Brunauer–Emmett–Teller (BET) model. However, Langmuir and Freundlich models were intensively used to calculate the adsorbed amount by a unit weight of solid sorbents. This review article aims to present the recently available information on utilizing the biomass materials for heavy metals removal. Here, we highlight the increasing use of these materials due to their low cost, regeneration ability, high adsorption efficiency, and small chemical or biological sludge with a possibility of metal recovery.
Porous sodium alginate/cellulose nanofiber composite hydrogel microspheres for heavy metal removal in wastewater

Ying Chen,Xin Liu,Rui Zhou,Jiaxian Qiao,Jiating Liu,Rong Cai,Jiaxian Liu,Jingjing Rong,Yi Chen

DOI: https://doi.org/10.1016/j.ijbiomac.2024.135000

2024-08-22

Abstract:High adsorption capacity, high adsorption rate and reusable adsorbents are urgent needed for removing heavy metals from wastewater. In this study, porous sodium alginate/cellulose nanofiber (SA/CNF) composite hydrogel microspheres were prepared by combining sodium alginate with cellulose nanofibers by microfluidics technology and adding polyethylene glycol (PEG) as pore making agent. The SA/CNF composite hydrogel microspheres could efficiently adsorb heavy metals (Pb2+, Cu2+ and Cd2+) in wastewater. The influencing factors of adsorption process, including pH, temperature, initial concentration, coexisting ions and aquatic environments, were systematically discussed. The adsorption process was more consistent with Langmuir isotherm model and pseudo-second-order model in batch system, indicating the adsorption process was mainly chemical adsorption. The adsorption capacity to Pb2+ obtained by Langmuir model was as high as 544.66 mg/g at 20 °C. Fixed-bed column adsorption experiments demonstrated the excellent performance of the as-prepared SA/CNF microspheres for treatment of the flowing wastewater in a column system. Overall, a highly practical adsorption process based on hydrogel adsorbents was developed for the removal of heavy metals from actual wastewater.
Removal of heavy metals from aqueous solution using carbon-based adsorbents: A review

Chengyu Duan,Tianyu Ma,Jianyu Wang,Yanbo Zhou

DOI: https://doi.org/10.1016/j.jwpe.2020.101339

IF: 7

2020-10-01

Journal of Water Process Engineering

Abstract:<p>Heavy metal contamination has been a serious threat to environment and human health. Carbon-based materials, from biochar/activated carbon to modified materials (i.e. carbon nanotubes-based materials, and graphene-based materials), have been widely studied as efficient adsorbents for the heavy metal removal from aqueous solutions. This review discussed the recent achievements in adsorption isotherms, adsorption kinetics and adsorption mechanism according to the existing forms of heavy metals in water. The effect of process conditions, such as temperature, pH value, and coexisting ions, on adsorption performance are combed, and the universal guidance law is obtained. The physical adsorption, electrostatic interaction, ion exchange, surface complexation, and precipitation/coprecipitation play important roles in heavy metals adsorption process. In addition to the common activated carbon(AC), biochar(BC) and the emerging carbon nanotubes(CNTs) and graphene(GN) adsorbent show good development potentials. Meanwhile, though the modified carbonaceous materials can achieve high adsorption capacity and removal efficiency of heavy metals, the modification operation is complex, especially chemical modification. Acid and alkali solution are often used to regenerate spent materials in desorption, however, further studies of other desorption reagent are really needed. This review highlights the removal of heavy metal ions from aqueous solution using carbon-based materials as adsorbents, and discusses the existing deficiencies and suggestions on further study.</p>

engineering, chemical, environmental,water resources
Adsorption of malachite green in aqueous solution using sugarcane bagasse-barium carbonate composite

Xuejing Fan,Ligao Deng,Kai Li,Haiqin Lu,Ruifeng Wang,Wen Li

DOI: https://doi.org/10.1016/j.colcom.2021.100485

IF: 5.633

2021-09-01

Colloid and Interface Science Communications

Abstract:The use of sugarcane bagasse (SCB) in water treatment has received an increasing amount of attention because of its characteristics and low cost. Bagasse was used as the matrix in this study. Barium chloride and sodium carbonate were mixed with bagasse under certain conditions to generate barium carbonate and to prepare the bagasse‑barium carbonate (SCB-BaCO3) composite adsorbent to adsorb the malachite green (MG) dye in the solution. MG’s adsorption on the adsorbent conformed to the Langmuir isotherm model, and the theoretical maximum adsorption capacity was 1250 mg/g. SCB-BaCO3 composite material is a low-cost, environmentally friendly, and efficient green adsorbent.

chemistry, physical,nanoscience & nanotechnology,materials science, coatings & films
Research on Adsorption of Heavy Metal Ions by Polysaccharide Hydrogels

Sen Liu,Yuting Cai,Mingjing Du,Jiahui Liu,Xinbin Zhang,Huizheng Yuan,Zhiwei Xu,Xiangyan Chen,Xinyuan Kan,Shaohua Zhang,Linlin Zhong,Songmei Ma

DOI: https://doi.org/10.1002/slct.202401752

2024-10-29

ChemistrySelect

Abstract:In this paper, the kinds of polysaccharide hydrogels, different synthesis methods, adsorption mechanism, and the influence of different environmental factors on the adsorption capacity of polysaccharide hydrogels were reviewed. In recent years, various industrial and agricultural problems have been highlighted, and the pollution of heavy metal ions to water bodies has become a considerable serious phenomenon. Adsorption method is an efficient, low‐cost, and easy to implement method for removing heavy metal ions, which does not produce secondary pollution, and has been widely used in water treatment. Polysaccharides are natural polymers, and their hydroxyl, carboxyl, and amine groups provide feasibility for the synthesis of hydrogels with various structures. The synthesized polysaccharide hydrogel has the characteristics of high adsorption capacity, specific adsorption, nontoxic, and so on. In this review, the kinds of polysaccharide hydrogels and different synthesis methods were discussed first. Then, the adsorption mechanism and different adsorption modes of polysaccharide hydrogels were reviewed. Finally, the effects of different environmental factors on the adsorption capacity of polysaccharide hydrogel were studied. The future research on the adsorption of heavy metal ions by polysaccharide hydrogels was proposed.

chemistry, multidisciplinary
Nanocellulose-Based Adsorbents for Heavy Metal Ion

Rongrong Si,Junwen Pu,Honggang Luo,Chaojun Wu,Gaigai Duan

DOI: https://doi.org/10.3390/polym14245479

IF: 5

2022-12-15

Polymers

Abstract:Heavy metal ions in industrial sewage constitute a serious threat to human health. Nanocellulose-based adsorbents are emerging as an environmentally friendly material platform for heavy metal ion removal based on their unique properties, which include high specific surface area, excellent mechanical properties, and biocompatibility. In this review, we cover the most recent works on nanocellulose-based adsorbents for heavy metal ion removal and present an in-depth discussion of the modification technologies for nanocellulose in the process of assembling high-performance heavy ion adsorbents. By introducing functional groups, such as amino, carboxyl, aldehyde, and thiol, the assembled nanocellulose-based adsorbents both remove single heavy metal ions and can selectively adsorb multiple heavy ions in water. Finally, the remaining challenges of nanocellulose-based adsorbents are pointed out. We anticipate that this review will provide indispensable guidance on the application of nanocellulose-based adsorbents for the removal of heavy metal ions.

polymer science
Synthesis of polyethylenimine modified sugarcane bagasse cellulose and its competitive adsorption of Pb2+, Cu2+ and Zn2+ from aqueous solutions

Wenyan Jiang,Yihao Xing,Leixing Mo,Jie Liao,Wei Chen,Haijun Wang,Tianshun Wang

DOI: https://doi.org/10.5004/dwt.2022.28805

IF: 1.1

2022-01-01

Desalination and Water Treatment

Abstract:In this study, a new biosorbent was prepared from sugarcane bagasse and polyethylenimine (MSCP). The effects of preparation parameters, including the polyethylenimine (PEI) concentration, the glutaraldehyde concentration, the reaction temperature, and ball milling time on the adsorption property of MSCP were studied. The optimum preparation conditions were as follows: the PEI concentration was 20%, the glutaraldehyde concentration was 2.0%, the reaction temperature was 318.15 K, and the ball milling time was 20 min. Under the optimum preparation conditions, the removal efficiency of Cu2+ by MSCP was reached 93.3%. The physical and chemical properties of MSCP were determined by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and elemental analysis. The SEM micrographs revealed that surface morphology of MSCP was rough, with many irregular folds and small particles. The FTIR and elemental analysis results indicated PEI was successfully grafted to the surface of sugarcane bagasse cellulose (SC) with glutaraldehyde as a bridge and the adsorption mechanism of heavy metals by MSCP can be regarded as the complexation between heavy metals and –NH2 groups of MSCP. Langmuir model showed the best fitting to the isotherm equilibrium data, the maximum adsorption capacities for Cu2+, Pb2+ and Zn2+ were 114.02, 165.56 and 95.79 mg/g, respectively. The adsorption experimental data were fitted well by pseudo-second-order. In multi-solute system, the competitive adsorption ability of heavy metals by MSCP followed the order of Pb2+ > Cu2+ > Zn2+.

engineering, chemical,water resources
Adsorption Removal and Recovery of Heavy Metal Pollutants by Agricultural and Forestry Wastes

李晓森,卢滇楠,刘铮

2012-01-01

Abstract:Agricultural and forestry wastes have the adsorption capacity of heavy metal ions,which can be used as biological adsorption applied in the industrial wastewater treatment and recovery of valuable heavy metals.This review focused on the recent advancement in the adsorption mechanism,adsorbent innovation and the downstream processing of the metal concentrates.The problems in research and development of agricultural and forestry wastes based adsorbent were also discussed.This review revealed the microscopic process of adsorption,clarified the role of the structure and composition related to the adsorption in the cell wall and determined the mechanism of adsorption of the heavy metal.The article pointed out that the development of new efficient biological adsorbents which perform high selectivity and adsorption capacity is the key step for application.After the adsorption of heavy metals,further processing is necessary for industrialization.

Removal of Heavy Metal Ions from Wastewater by Sugarcane Bagasse as Adsorbent

Changes in the Extractability and Fractionation of Cadmium and Copper in a Contaminated Soil Amended with Various Sugarcane Bagasse-Based Materials

A Review on the Mitigation of Heavy Metals from Aqueous Solution using Sugarcane Bagasse

Advances in Research on Treatment of Heavy Metal Ions Wastewater by Agricultural Waste

Recent Progress on the Adsorption of Heavy Metal Ions Pb(II) and Cu(II) from Wastewater

Synthesis of Cellulose–Poly(Acrylic Acid) Using Sugarcane Bagasse Extracted Cellulose Fibres for the Removal of Heavy Metal Ions

Adsorption of heavy metal ions by iron tailings: Behavior, mechanism, evaluation and new perspectives

Rotten sugarcane bagasse derived biochars with rich mineral residues for effective Pb (II) removal in wastewater and the tech-economic analysis

Organic Adsorbents Modified with Citric Acid and Fe3O4 Enhance the Removal of Cd and Pb in Contaminated Solutions

Application of biomass adsorbents in the treatment of heavy metals in wastewater: a review

Research progress on chemical modification of waste biomass cellulose to prepare heavy metal adsorbents

Recent progress in electrospun nanofibers and their applications in heavy metal wastewater treatment

Removal of heavy metals from wastewater using agricultural byproducts

Porous sodium alginate/cellulose nanofiber composite hydrogel microspheres for heavy metal removal in wastewater

Removal of heavy metals from aqueous solution using carbon-based adsorbents: A review

Adsorption of malachite green in aqueous solution using sugarcane bagasse-barium carbonate composite

Research on Adsorption of Heavy Metal Ions by Polysaccharide Hydrogels

Nanocellulose-Based Adsorbents for Heavy Metal Ion

Synthesis of polyethylenimine modified sugarcane bagasse cellulose and its competitive adsorption of Pb2+, Cu2+ and Zn2+ from aqueous solutions

Adsorption Removal and Recovery of Heavy Metal Pollutants by Agricultural and Forestry Wastes