Abstract:In this study, Ni-based, Ni+WC and Ni+WC+Cr3C2 cladding coatings (named by Ni-1, Ni-2, Ni-3, respectively) were prepared by a hybrid fabrication method combining laser cladding technology with pre-placed powders and ultrasonic impact treatment. Comparative analysis of microstructures and surface properties indicated that gamma-(Fe, Ni) solid solution was the main phase in three coatings besides M23C6, W2C and WC carbides while ultrasonic impact treatment did not change the phase compositions of Ni-based coatings. For Ni-1 cladding coating, there existed cellular dendrites with fishbone-like precipitates at the bottom region while dendrites and equiaxed dendrites appeared at the middle and top region. In Ni-2 cladding coating, cellular dendrites and eutectic structures with flocculent characteristics were generated. By contrast, most of WC particles sank at the bottom region while polygonal Cr3C2 particles distributed at the middle and top regions in Ni-3 cladding coating. After ultrasonic impact treatment, a obvious plastic deformation layer was produced in Ni-1 coating and original reticular eutectic structures are broken into particles. In Ni-2 coating, both the eutectic structures and polygonal carbides were impacted into fine ones. As for Ni-3 coating, local collapse phenomenon occurred while the ex-istence of Cr3C2 and WC particles prevented the plastic deformation of the surface layer. The maximum average microhardness (831HV0.1) and the lowest weight loss were obtained in Ni-3 cladding coating. While corrosion resistance of laser cladding Ni-1 coating in 3.5 wt% NaCl solution was better than other two kinds of Ni-based composite coatings. After UIT, both the wear resistance and corrosion resistance were enhanced obviously resulting from grain refinement and dispersion strengthening.

Effect of Cr Additives on the Microstructures and Properties of Laser Cladded Ni3Si

Effect of Carbonization-easily-form Elements Nb and Ti on Properties of Laser Cladding Ni3Si Coatings

Effect Of Ni Content On Cracking Susceptibility And Microstructure Of Laser-Clad Fe-Cr-Ni-B-Si Alloy

Optimizing the Electrochemical Corrosion Performance of Laser Cladded Ni-based Single Crystal Superalloy Via Manipulation of Γ′(ni3al) Phase

Intermetallic Alloys Ni<sub>3</sub>Si and Ni<sub>3</sub>(Si,Ti): Microstructures and Properties

Intermetallic Alloys Ni3si And Ni-3(Si,Ti): Microstructures And Properties

Effect of laser parameter on microstructure and microhardness of NiCrBSi laser cladding layer

Corrosion Resistance of Laser Clad Cr-alloyed Ni2Si/NiSi Intermetallic Coatings

Structure and Properties of NiCrSiB Alloy Laser Cladding

Influence of process parameters on the Mo2Ni3Si/γ-Ni coatings by laser cladding

Microstructure and Corrosion Resistance of Laser Clad Ni-Si Silicides Composite Coating

Microstructure and Properties of Laser Cladding FeCrBSi Composite Powder Coatings with Higher Cr Content

Effect of Ni Content on Microstructure and Hardness of Laser Cladding Layers

Effect of Y2O3 addition on microstructure of Ni-based alloy + Y2O3/substrate laser clad

Microstructure and Solidification Process of the Laser Clad Ni Alloy

Reinforced Microstructure and High Temperature Oxidation Resistance of Ni-based Alloy Coating by Laser Cladding of SiC Nanometer Powder

Effect of Ti Addition on Microstructural Evolution of Ni3si

Comparative Investigation on Microstructures and Properties of WC/Cr3C2 Reinforced Laser Cladding Ni-based Composite Coatings Subjected to Ultrasonic Impact Treatment

Micro structure and hardness of Ni-/NiCr-Cr3C2 coating by laser cladding

Microstructure and Properties of Ni-3(Si,Ti) Intermetallic Cladding with Nb Addition

Microstructure of Laser-Clad SiC-(Ni Alloy) Composite Coating