Study of Railway Axle Ultrasonic Testing Technology and Ability Improvement *
Chaoyong PENG,Xiaorong GAO,Yu ZHANG,Jianping PENG,Ai WANG,Bo ZHAO,Yang YANG
2016-01-01
Abstract:Axle is one of the key components involved in the s afety of railway transportation. As the complex state of axle with s hocks, torsion stress and tensile stress, the fatigue crack will leading to axle fail ure. In order to ensure the safety of railway transportation, defects detection at axle i nner parts and press -fit parts should be done, which can be implemented by ultrasonic met hod. In this study, the phased array ult rasonic is used in axle press-fit parts de fect detection which can great ly improve the defect detection ability and operating speed. Different axle detection schemes are designed to realize full coverage accor ding to different applications and different maintenance levels. The axle press-fit in terface echoes always interfere with the defect resolution, and the defect missing rate and false rate will increase due to the low SNR. A median filter fused anisotropic diffusio n algorithm is proposed for improving SNR of the axle detection echoes, thus to improve the ultrasonic defect detection ability. In the end, the performance of t he denoising algorithm is assessed using axle press-fit part detection data and some i nd icators comparison. Introduction With rapid development of high-speed and heavy-haul railways , the safety of railway operations is becoming increasingly important. Long-term and high-c ycle service of the railway axles results in deteriorated axle state as it bea rs rotating bending loads and impacting of wheel-rail interaction [1]. (a) Broken axle (b) Fatigue cracks Fig. 1. Broken axle and fatigue cracks Under the combined impacts of tension, compression, distortion, and s hear stress, the axle is prone to fatigue damage. When the fatigue crack grows a certai n depth, the load bearing More info about this article: http://ndt.net/?id=19504 2 capacity decreases thus instantaneous fracture may occur [2] . A broken axle and the fatigue cracks of press fit zone are shown in Fig. 1. To ensure the safety of railway wheels and axles, n on-destructive testing technologies, especially ultrasonic testing and magnetic particle testi ng, are widely used. Wheels, gears, and some brake discs are pressed or shrunk onto axles. Defects in the axle pr ss-fit zone can be detected only by using ultrasonic testing methods, with ultra sonic probes placed on the axle body or the axle end face. With multiple beams and angles, the phased arr y (PA) probe is faster and more flexible in defect detection than conventi onal one. Different axle testing schemes are designed by sound field si mulat on software (CIVA) to realize full ultrasonic coverage according to different a pplications and maintenance levels. But no matter which kind of testing schemes is used or w here the probe is fixed, the axle pressfit interface echo always overlaps the defect echo be caus of the interference fit [3], fretting corrosion [4] and complex interface stress distr ibu ion [5-6]. To improve the signal to noise ratio (SNR), a median filter merged anisotropic diffus ion (MAD) algorithm is proposed to suppress the press-fit echo, thus the detection ability is improved. In the end, the performance of the proposed algorithm is assessed using SNR a nd contrast to noise ratio (CNR). 1. Axle Testing Technology 1.1 Phased Array Ultrasound In recently years, phased array ultrasound is developed and become more and more popular, especially for special inspection requirements such as com plex geometric components and high inspection efficiency solutions. The phased array ult rasound features beam deflection and dynamic focusing without moving probe [7], so that the coupling is c omplete and stable, thus the detection efficiency is improved. Fig. 2. The beam focusing and deflection of PA probe 1.2 Testing Schemes Design In Chinese locomotives light maintenance level, the wheel-s t is mounted under locomotive, and assembled with motor, gear, gear box, bearing and some protec tion parts. In this case, the only way for axle ultrasonic inspection is to inspect from the axle end f ace with axle cap open. With beam steering and focusing, a group of ultrasonic beams can be generated by adjusting the setup parameters of one PA probe, instead of numbers of convention al ultrasonic probes. Different working models are used for full ultrasonic coverag , as shown in Fig.3 Sector scan is realized as shown in Fig.3(a). In the second model, the PA probe transmit and receive longitudinal wave to evaluate general state of the axle mater ial, as shown in Fig.3(b). In the