Abstract:Prediction of the flexural strength of a laminated composite is important for engineering application yet difficult in nature. The purpose of this paper is to analyse the progressive failure process of laminated composites subjected to a bending load, with application to those reinforced by knitted fabrics. The analysis is based on the classical lamination theory and a bridging micromechanics model [Compos. Part A 32 (2) (2001) 143–172]. Only the mechanical properties of constituent fiber and matrix materials under the bending load condition and the laminate geometric parameters are required. All these data can be measured independently before composite fabrication. As the internal stresses in the fiber and matrix have been explicitly determined using the bridging model, a lamina in the laminate is considered to have failed whenever any of its constituents fails, according to a stress failure criterion. Then, a stiffness discount is applied to the failed lamina, and a predicted progressive failure process results. Unlike in an in-plane load situation where the ultimate tensile strength occurs when the laminate’s last ply fails, the ultimate bending strength of the laminate is attained generally before its last-ply failure. As one does not know a priori which ply failure corresponds to the ultimate failure, the use of only the stress failure criterion is no longer sufficient for the determination of the laminate ultimate strength. An additional critical deflection or curvature condition must be adopted either. The critical deflection or curvature is the laminate deflection or curvature corresponding to which the ultimate bending strength is measured. Experiments have been carried out to obtain the bending stiffness and strength of laminated beams reinforced with six layers of plain weft knitted fabrics under four-point bending. The laminate lay-ups used are: [0/0/0/0/0/0], [90/90/90/90/90/90], [0/90/90/90/90/0], [90/0/0/0/0/90], and [0/45/−45/−45/45/0], where 0 denotes that the fabric wale direction is along the beam axial direction. Using a matrix combustion and fabric peeling out method, it has been found that only some of the layers in the laminates failed after the bending test. For these laminates and based on the stress failure criterion, the predicted load–deflection curves till the fourth-ply failure agree reasonably with the experimental data. By incorporating with the critical deflection condition, the laminate ultimate bending strengths thus obtained correlate favourably with the measured results.

Development of a novel flexible composite material

An Experimental Study on Stretchy and Tough PDMS/Fabric Composites

Characterization of a Knitted Fabric Reinforced Elastomer Composite

Characterization of mechanical properties of stab-resistant angle-ply flexible composites

Mechanical Deformation Mechanisms in Knitted Fabric Composites

Fabrication and characterization of laminated natural fibers and SS303 wire mesh reinforced epoxy-based hybrid composite

Modeling The Stress/Strain Behavior Of A Knitted Fabric-Reinforced Elastomer Composite

Development of reinforced composite materials with a nanoporous textile substrate and a brush-structured polymer interfacial layer

Impact of yarn compositions, loop length, and float stitches on the mechanical behavior of knitted fabrics via full factorial design and RSM

Mechanical properties of flexible composites reinforced with high-performance glass fiber multi-axial warp-knitted fabrics

Influence of inlay yarn type and stacking sequence on mechanical performance of knitted uni-directional thermoplastic composite prepregs

Investigating the Effects of Anisotropy of Knitted Fabric Reinforced Polymer (KFRP) Composite

Extremely Tough Composites from Fabric Reinforced Polyampholyte Hydrogels

Investigations on the development of impact-resistant thermoplastic fibre hybrid composites from glass and steel fibre

A Micromechanical Approach to the Tensile Strength of A Knitted Fabric Composite

An Investigation on the Polymer Composite Medical Device - External Fixator

The Effect of Textile Structure Reinforcement on Polymer Composite Material Mechanical Behavior

Progressive Flexural Failure Analysis of Laminated Composites with Knitted Fabric Reinforcement

STRENGTH , CRACK INITIATION AND CRACK PROPAGATION IN FABRIC BASED FLEXIBLE AND SEMIFLEXIBLE COMPOSITES

An experimentally validated anisotropic visco-hyperelastic constitutive model for knitted fabric-reinforced elastomer composites

Fabrication of ramie/hemp fibers-reinforced hybrid polymer composite—A comprehensive study on biological and structural application