Abstract:The analog-to-digital converter (ADC) is a key building block of today's high-volume systems-on-a-chip (SoCs). Built-in-self-test (BIST) is the most promising solution to testing deeply-embedded ADCs. Cost-effective stimulus source with on-chip integrability has been viewed as the bottleneck of ADC BIST, and consequentially the bottleneck of SoC BIST and BIST-based self-calibration. The deterministic dynamic element matching (DDEM) technique has been proposed as a solution to this problem. In this work, rigorous theoretical analysis is presented to show the performance of a DDEM digital-to-analog converter (DAC) as an ADC linearity test stimulus source. Guided by the insight obtained this analysis, a systematic approach for cost-effective DDEM DAC design is proposed. Two generations of DDEM DACs have been designed, fabricated, and measured. 12-bit equivalent linearity was achieved from the first DDEM DAC with 8-bit apparent resolution and less than 5-bit raw linearity after systematic error compensation. The achieved 12-bit linearity outperforms any on-chip stimulus source in literature. Based on the first design, a new DDEM DAC with 12-bit apparent resolution, 10-bit raw linearity, and 9-bit DDEM switching was designed with improved design technique. This DAC was fabricated in standard 0.5-pm CMOS technology with a core die area of 2 mm2. Clear ramp signals could be observed on an oscilloscope when the DDEM DAC was clocked at 100 MHz. Laboratory testing results confirmed that the new DDEM DAC achieved at least a 16-bit equivalent linearity; this was limited by the available instrumentation, which has 18-bit linearity. It outperforms any previously reported on-chip stimulus source in terms of ADC BIST performance by 5 bits. The robust performance, low cost, and short design cycle for on-chip implementation make DDEM an enabling technology for SoC BIST and self-calibration. Two new approaches based on DDEM are developed to further boost the die area efficiency, improving the basic DDEM approach. The first is termed segmented DDEM, and the second is dither-incorporated DDEM (DiDDEM). It has been shown through mathematical analysis and simulation that these can maintain the performance of the basic DDEM approach while greatly reducing the implementation cost.

High-Resolution ADC Linearity Testing Using a Fully Digital-Compatible BIST Strategy

A Fully Digital-Compatible BIST Strategy for ADC Linearity Testing

Modeling of a 14-bit, 100-MS/s pipelined ADC with digital nonlinearity calibration

A Low-Cost On-Chip Built-In Self-Test Solution for ADC Linearity Test

Modeling of digital background calibration with signal-dependent dithering for a 14-bit, 100-MS/s pipelined ADC

A Calibration Scheme for a 800-Ms/s 14 Bit Pipelined ADC in 28-Nm CMOS

High-Precision ADC Testing with Relaxed Reference Voltage Stationarity.

A 14bit 500MS/s 85.62dBc SFDR 66.29dB SNDR SHA-less pipelined ADC with a stable and high-linearity input buffer and aperture-error calibration in 40nm CMOS

A Maximum-Likelihood-Estimation-Based Digital Background Calibration Technique for Interstage Gain Error in Pipelined ADCs

A 14-bit 500MS/s and 1GS/s Configurable Pipelined ADC with Background Calibration

Low-cost high-quality constant offset injection for SEIR-based ADC built-in-self-test

Low-Cost Linearity Testing of High-Resolution ADCs Using Segmentation Modeling and Partial Polynomial Fitting

Deterministic dynamic element matching: an enabling technology for soc built-in-self-test

A 14-Bit Pipelined ADC with Digital Background Nonlinearity Calibration.

A Novel Linear Histogram BIST for ADC

ADC-BIST Testing Method in Electrical Imaging Well Logging Tools

Testing high resolution ADCs using deterministic dynamic element matching

INL and DNL Estimation Based on Noise for ADC Test

A High Linearity,13bit Pipelined CMOS ADC

A BIST Approach to Approximate Co-Testing of Embedded Data Converters

A High Accuracy and Bandwidth Digital Background Calibration Technique for Timing Skew in TI-ADCs