Abstract:The ability to undercool and solidification mechanism of liquid quinary Ni40Zr28.5Ti16.5Al10Cu5 alloy are investigated by electromagnetic levitation (EML) and drop tube (DT) technique. Under the EML condition, the maximum undercooling of levitated alloy can reach up to 290 K (0.21TL). Under the DT condition, the alloy achieves higher undercooling than EML, and solidifies finally into metallic glass. At lower undercooling, the solidification structure of the alloy is composed of primary Ni3Ti phase, secondary Ni10Zr7 phase and eutectic (Ni10Zr7+Ni21Zr8) phase. With the rise of undercooling, the solidification structure displays the following evolution events: phase morphology refinement, primary phase inhibition, phase number reduction, and amorphous phase formation. By using the high-speed cinematography technique, three nucleation modes are distinctly observed on the levitated alloy melt surface at the beginning of solidification, that is, single-point nucleation, multi-point nucleation and annular nucleation. The levitation state corresponding to single-point mode nucleation is relatively stable, and the alloy undercooling is also relatively low. The annular nucleation only occursin the case with high rotation speed, and the undercooling is greater than 208 K. The discrepancy between nucleation modes is due to the He gas flow for forced cooling. The theoretical calculations indicate that the alloy droplets achieve high undercoolingand large cooling rate under the DT condition. The experimental results show that when the droplet diameter decreases to 498 μm, the amorphous phase begins to appear in the alloy particles. It is noteworthy that the amorphous phase is preferentially formed inside the droplet, but not on the outer surface. The morphology of solidification structure reveals that different regions of the droplet have various local undercoolings, which result in the distribution characteristics of amorphous phase. The volume fraction of amorphous phase increases linearly with the decrease of particle diameter. When the droplet diameter decreases to 275 μm, the alloy droplets are completely frozen into glassy particles. The average eutecticspacing values are also measured at different alloy undercoolings. Compared with the classical binary eutectic growth model, the experimental eutectic growth law exhibits a large deviation in index. This indicates that the eutectic growth in multicomponent alloys displays more complex kinetic characteristics.

A simulation study of rapid solidification and crystal configuration of Cu 70 Ni 30 alloy

Molecular Dynamics Simulation on Structural Evolution During Crystallization of Rapidly Super-Cooled Cu50Ni50 Alloy

Molecular-dynamics Simulations of the Solidification Processes of Binary Liquid Metals: Cu-Ni and Cu-Ag

MD Simulation on Crystallization Mechanisms of Rapidly Supercooled Fe-Ni Alloys

Simulation Study of Effect of Cooling Rate on Evolution of Microstructures During Solidification of Liquid Metal Cu

Molecular Dynamics Simulation on Structures of Cu-Ni Alloy

The Effects of Cooling Rate on Solidification Microstructure of Cu70Ni30 Alloy

Rapid dendritic solidification and structure hardening mechanism of substantially undercooled quaternary nickel alloys

Simulation Study for Atomic Size and Alloying Effects During Forming Processes of Amorphous Alloys

Dendritic Growth and Solute Trapping in Rapidly Solidified Cu-based Alloys

Rapid Solidification Mechanism of Liquid Quinary Ni-Zr-Ti-Al- Cu Alloy Investigated by High-Speed Cinematography

Simulation Study of Effect of Initial Melt Temperature on Microstructure Evolution of Liquid Metal Ni During Solidfication Process

Molecular Dynamics Simulation Studies of Atomic-Level Structures in Rapidly Quenched Ag-Cu Nonequilibrium Alloys

Crystallization Behavior of Fe70Ni10Cr20 During Rapid Solidification under Different Cooling Rates

Solute Redistribution and Micromechanical Properties of Rapidly Solidified Multicomponent Ni-based Alloys

Thermophysical Properties and Rapid Solidification of an Undercooled Liquid Hexabasic Ni-Based Alloy

Simulation of Formation and Evolution of Nano-Clusters During Rapid Solidification of Liquid Ca70Mg30 Alloy

Crystallization Insights Revealed by Simulation Solidification Study of Fe63Ni33Co4 Alloy Melt at Subcritical Cooling Rate

Molecular dynamics simulation of liquid Cu during isothermal solidification

Molecular Dynamics Simulation of Rapid Solidification of Cu<sub>64</sub>Zr<sub>36</sub> Nanodrops of Different Sizes

Molecular-dynamics simulations of the rapid cooling processes in binary liquid metals: AgxCu1-x