Abstract:In this study, Al-20 wt% Mg 2 Si composites were prepared using an in situ endogenous process method. Various amounts of Sc were added to the composites, and a heat treatment process was employed to optimize the microstructures of the materials and enhance the overall properties of the composites. The study results indicate that the addition of Sc has a significant positive effect on both the microstructure and mechanical properties of Al-20 wt% Mg 2 Si composites. The inclusion of Sc leads to a more regular and uniformly distributed morphology of the primary Mg 2 Si phase, accompanied by a significant reduction in grain size. Particularly, when the Sc content is 0.3 wt%, the composite exhibits the most notable grain refinement effect, resulting in the best mechanical performance. The tensile strength reaches 152.7 MPa, the hardness measures 92.9 HV and the elongation is 2.82%. Through the heat treatment process, the morphology and distribution of the initial Mg 2 Si phase in the composites were optimized, resulting in significant improvements in both the morphology and distribution of the initial Mg 2 Si phase and the eutectic structure. Consequently, the tensile strength increased to 204.3 MPa, the hardness reached 117.8 HV, and the elongation improved to 3.72%. Finite element simulation was employed to model the tensile behavior of real microstructures of Al-20 wt% Mg 2 Si-0.3 wt% Sc composite in both as-cast and heat-treated conditions. The simulation results demonstrate good agreement with experiment. The fracture modes observed in both cases involve interfacial debonding and intergranular fracture. The simulation effectively showed the deformation process and stress distribution during tensile fracture. Moreover, the heat-treated model exhibits a higher load on the particles compared to the as-cast state. This finding provides evidence that the overall properties of Al-Mg 2 Si composites are enhanced following the heat treatment process.

Study on the Yield Behavior of Al2O3–SiO2(sf)/Al–Si Metal Matrix Composites

Micro-yield Behaviors of Al2O3-SiO(subscript 2(sf))/Al-Si Metal Matrix Composites

Micro-Yield Behaviors of Al2o3-Sio2(Sf)/Al-Si Metal Matrix Composites

Studies on Microyield Behavior of Sicp/2024al Composite Materials

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Effect of heat treatment on dislocation states and work hardening behaviors of SiCw/6061Al composite

Effect of Thermal Cycling Treatment on Microyield Behavior of Al 2 O 3 p/Al Composite

Microstructure and mechanical properties of the α-SiAlON/α-SiC composites: Effects of heat treatment

Effect of Low Temperature Treatment on Tensile Yield Strength of Sicw/6061 Al Alloy Composites

Study on Microstructure and Tensile Property of Sub-micron MgAl2O4(p)Al-Mg-Si Composite

Effect of low temperature treatment on tensile yield strength of SiV6061 Al alloy composites®

An experimental study on deformation behavior below 0.2% offset yield stress in some SiCp/Al composites and their unreinforced matrix alloys

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Effect of Sc Addition and Heat Treatment on the Fracture Behavior of Al-20%Mg2Si Composites: Experiments and Finite Element Simulations

Effect of heat treatment on the microstructure, mechanical properties and fracture behaviors of ultra-high-strength SiC/Al–Zn–Mg–Cu composites

Micro-yield property of sub-micron Al2O3 particle reinforced 2024 aluminum matrix composite

Effects of processing parameters and post-process heat treatment on selective laser melted SiC/AlSi10Mg composites

A STUDY ON STRENGTHENING BEHAVORS OF ALUMNIUM MATRIX COMPOSITES REINFORCED WITH CARBON SILLICON WHISKER

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Microstructure And Mechanical Properties Of The Alpha-Sialon/Alpha-Sic Composites: Effects Of Heat Treatment

Influence of Cu content on interfacial microstructure of Al2O3-SiO2 fiber reinforced Al matrix composites