Abstract:Square wave alternating current (AC) tungsten inert gas (TIG) welding possesses great advantages in welding stability, quality, flexibility, and cost in manufacturing thin-walled propellant storage tanks with 2219-T6 aluminum alloy. To solve the welding engineering problem of 4 mm-thick plates made by square wave AC TIG welding, we conducted process optimization experiments and performed common microstructure analysis and mechanical property testing. Tensile strength and microhardness reaching 63.8 and 83.1% of the base material appear in the optimal weld. The dendrite morphology, grain size, and eutectic content of all welds were compared and analyzed with optical microscopic observation, image segmentation, and grayscale statistics. The obtained quantitative results interpret the macroscopic properties of the optimal weld from a microscopic perspective. Shallow and uniform equiaxed dimples, evident tearing ridges, and second-phase particles were detected in the tensile fractures. Reticular, granular, and lath eutectic ( α (Al) + CuAl 2 ) were found in the interior and boundaries of dendritic solid solution ( α (Al)). Unexpectedly, the epitaxial growth of the columnar grains was inconspicuous or absent in all welds. Uniform and fine equiaxed grains occupy almost all welds of different process parameters, while the G/R ratio of these welds reaches 15-23 °C·s/mm^2, under which the equiaxed crystals should not have formed. We attributed the grain refinement in these welds to the secondary phase particles in base metal. They are broken into fragments during the multi-pass rolling process of plates, remain semi-dissolved under a fast cooling rate, and provide adequate heterogeneous nuclei for melt solidification. A further SEM and EDS test to base metal and secondary phase particles confirmed our findings and speculations. These results suggest that in the molten pool with sufficient heterogeneous nucleation, the mechanical blocking effect of heterogeneous nucleation may interfere with the thermodynamic effect of welding heat input and speed on grain structure.

GTAW Repair-welding Technology on the Large-size Turbine Generator Rotor Made of the 25Cr2ni4mov

Weld repair of gas turbine disc: optimization of pulsed TIG welding process parameters and microstructural analysis of Cr–Mo-V Steel

TIG Repairing on Directionally Solidified Superalloy DZ125

Microstructure Characterization of SAW and TIG Welded 25cr2ni2mov Rotor Steel Metal

Characterization on the Microstructure Evolution and Toughness of TIG Weld Metal of 25cr2ni2mov Steel after Post Weld Heat Treatment

Microstructure and Mechanical Properties of Wire Arc Additive Repairing Ti–5Al–2Sn–2Zr–4Mo–4Cr Titanium Alloy

Cold-Source Composite Welding Repair of 9Cr2Mo Thick-Walled Parts: Microstructure, Mechanical Properties, and Finite Element Simulation

Research on the micro zone strength and strain hardening behavior in the 30Cr2Ni4MoV rotor welded joint

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Influence of Microstructure on the Micro-Region Fracture Toughness of the 30cr2ni4mov Turbine Rotor Welded Joint

The Engine Casing Machining Holes Repairing Based on Vibration Wire Feeding

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Microstructure and Mechanical Characteristics of Dissimilar TIG Welded 9% Cr Heat-Resistant Steels Joints

Development of weld filler material to match the advanced martensitic heat resistance steel G115 and tailoring the performance by tempering temperature

An investigation on the suitability of different welding recovery procedures for cold stamping punches in VF800AT steel

Research on Laser Repair Technology for Surface Defects of Flywheel Disc Steel Plate

New Technique to Repair Keyhole of 2195 Al-Li Alloy Friction Stir Welding Joints

Titanium Alloy Repair with Wire-Feed Electron Beam Additive Manufacturing Technology

Research on TIG repairing technology for ZM6 magnesium alloy casting

Technology-Based Recontouring of Blade Integrated Disks After Weld Repair

Refining Microstructures and Enhancing Mechanical Properties of Inconel 718 Weldment Via Fast-Frequency Double Pulsed Waveforms Adopting in FFP-TIG