Abstract:Poly(lactide- co -glycolide) and poly(lactic-co-glycolic acids) (PLGAs) play a critical role in the development of commercial long-acting injectable microsphere formulations. However, very little information is available describing the impact of PLGA manufacturer and monomer distribution along the polymer chain (e.g, glycolic blockiness (R c ) and average lactic block length (L L )) on the degradation and release behavior of PLGA drug carriers in vitro and in vivo. Here, we compared the in vitro and in vivo performance of ( a ) four leuprolide-loaded microsphere formulations prepared from similar low-molecular-weight acid-capped PLGAs (10–14 kD, i.e, Expansorb ® DLG 75-2A, Purasorb ® PDLG 7502A, Resomer ® RG 752H and Wako ® 7515) and ( b ) two triamcinolone acetonide-loaded (Tr-A) microsphere formulations from similar medium-molecular-weight ester-capped PLGAs ( i.e. , Expansorb ® DLG 75-4E and Resomer ® RG 753S). Lupron Depot ® and Zilretta ® were used as reference commercial products. The six 75/25 PLGAs displayed block lengths that were either above or below values expected from a random copolymer. Drug release and polymer degradation were monitored simultaneously in vitro and in vivo using a cage implant system. The four leuprolide-loaded formulations showed similar release and degradation patterns with some notable differences between each other. Microspheres from the Expansorb ® polymer displayed lower L L and higher R c relative to the other 3 PLGA 75/25 microspheres, and likewise exhibited distinct peptide release and degradation behavior compared to the other 3 formulations. For each formulation, leuprolide release was erosion-controlled up to about 30% release after the initial burst followed by a faster than erosion release phase. In vitro release was similar as that in vivo over the first phase but notably different from the latter release phase, particularly for the most blocky Expansorb ® formulation. The Purasorb ® and Wako ® formulations displayed highly similar performance in release, degradation, and erosion analysis. By contrast, the two ester-capped Expansorb ® DLG 75-4E and Resomer ® RG 753S used to prepare Tr-A microspheres shared essentially identical L L and higher R c and behaved similarly although the Expansorb ® degraded and released the steroid faster in vivo, suggestive of other factors responsible (e.g., residual monomer). The in vivo release performance for both drugs from the six microsphere formulations was similar to that of the commercial reference products. In summary, this work details information on comparing the similarities and differences in in vitro and in vivo performance of drug-loaded microspheres as a function of manufacturing and microstructural variables of different types of PLGA raw materials utilized and could, therefore, be meaningful in guiding the source control during development and manufacturing of PLGA microsphere-based drug products. Future work will expand the analysis to include a broader range of L L and higher R c , and add additional important formulation metrics (e.g., thermal analysis, and residual monomer, moisture, and organic solvent levels).

Fabrication and Characterization of Controlled Release Poly(d,l-Lactide-co-glycolide) Millirods

Development and characterization of dual-release poly(D,L-lactide-co-glycolide) millirods for tumor treatment

Modulating Drug Release from Short Poly(ethylene Glycol) Block Initiated Poly(L-lactide) Di-block Copolymers

Fabrication of porous poly(L‐lactide‐co‐ε‐caprolactone) micropowder for microbubble effect and ultrasound‐mediated drug delivery

Combined modeling and experimental approach for the development of dual-release polymer millirods.

Development of poly (lactic-co-glycolic acid) (PLGA) based implants using hot melt extrusion (HME) for sustained release of drugs: The impacts of PLGA's material characteristics

[Preparation, Characterization and Drug Release Characteristics of Poly(lactide)(pl)/poly(lactide-Co-polyethylene Glycol)(pleg) Blend Microspheres].

Sustained Release of Doxorubicin from a Thermosensitive Hydrogel

Poly(lactic-co-glycolic acid) microsphere production based on quality by design: a review

Membrane-Encased Polymer Millirods for Sustained Release of 5-Fluorouracil

A Green Approach to Producing Polymer Microparticles for Local Sustained Release of Flavopiridol

Optimizing the Fabrication of Shape-Defined Microparticles for Sustained Drug Delivery: the ‘Less is More’ paradigm

Fabrication of Poly Lactic- co-Glycolic Acid Microneedles for Sustained Delivery of Lipophilic Peptide-Carfilzomib

Controlled release of goserelin from microporous polyglycolide and polylactide

PLGA implants for controlled drug release: Impact of the diameter

Effect of PLGA raw materials on in vitro and in vivo performance of drug-loaded microspheres

3D printed PLGA implants: How the filling density affects drug release

Synthesis, Characterization and Application of Poly(lactic-co-glycolic acid) with a Mass Ratio of Lactic to Glycolic Segments of 52/48

Fabrication and in vitro drug release study of microsphere drug delivery systems based on amphiphilic poly-α,β-[N-(2-hydroxyethyl)-l-aspartamide]-g-poly(l-lactide) graft copolymers

The Effects of Lactidyl/Glycolidyl Ratio and Molecular Weight of Poly(D,L-Lactide-Co-Glycolide) on the Tetracycline Entrapment and Release Kinetics of Drug-Loaded Nanofibers

Microfluidic preparation of monodisperse PLGA-PEG/PLGA microspheres with controllable morphology for drug release.