Abstract:We present detailed investigations of the fabrication and characterization of photovoltaic devices consisting of poly(3-hexylthiophene) (P3HT) intercalated into a mesoporous structure of ZnO nanofibers. ZnO nanofibers were grown via a low-temperature hydrothermal route from a solution of zinc nitrate precursor. P3HT was spin-coated on top of the structure, and intercalation into the voids between the nanofibers was induced with annealing. A silver electrode was used as the top contact. Spin-coating, storage, and testing of the device were performed in air. We discuss the effects of atmosphere and ZnO nanofiber morphology on device performance. Optimized nanofiber devices exhibited a 4-fold increase in the short circuit current (2.17 mA/cm2) as compared to that of a planar ZnO−P3HT bilayer device (0.52 mA/cm2) as a result of the increased donor−acceptor interfacial area. The efficiency of the nanofiber based device under 1 sun-simulated solar illumination was 0.53% and was found to increase at higher incident light intensities, reaching a value of 0.61% at 2.5 suns. Additionally, we found that for these devices fabrication in and exposure to air is required to obtain good diode characteristics. We also show that the morphology of the ZnO nanostructures in the nanocomposite directly impacts device performance. Treatment of the ZnO surface using surfactants increased the open circuit voltage at the expense of the short circuit current; however, there was little effect on overall device efficiency. Because of the inverted geometry of this device that allowed for the use of a silver top contact, the device was not susceptible to oxidative degradation when stored in the dark.

Effect of 3,4,9,10-Perylenetetracarboxylic Dianhydride on the Performance of Zno Nanorods/Polymer Hybrid Solar Cell

Hybrid Bulk Heterojunction Solar Cells Based on Poly (3-Hexylthiophene) and Z907-modified ZnO Nanorods

The Effect of Modified Layers on the Performance of Inverted ZnO Nanorods/meh-Ppv Solar Cells

Preparation of a Hybrid Polymer Solar Cell Based on MEH-PPV/ZnO Nanorods

Enhancing the performance of poly(3-hexylthiophene)/ZnO nanorod arrays based hybrid solar cells through incorporation of a third component

The Effect of Atmosphere and ZnO Morphology on the Performance of Hybrid Poly(3-hexylthiophene)/ZnO Nanofiber Photovoltaic Devices

Hybrid Polymer:Colloidal Nanoparticle Photovoltaic Cells Incorporating A Solution-Processed, Multi-Functioned Zno Nanocrystal Layer

Electronic Structure Effect of Polythiophene Derivatives and Nano N-Zn-Ag/TiO 2 on Performance of Organic Thin Film Solar Cell

PERFORMANCE ENHANCEMENT OF CdS NANOROD ARRAYS/P3HT HYBRID SOLAR CELLS VIA N719 DYE INTERFACE MODIFICATION

The Influence Of Interface Modifier On The Performance Of Nanostructured Zno/Polymer Hybrid Solar Cells

Device Performance Related to Amphiphilic Modification at Charge Separation Interface in Hybrid Solar Cells with Vertically Aligned Zno Nanorod Arrays

Polydopamine/ZnO Nanocomposites As a New Electron Transport Layer for PTB7: PC70BM Solar Cells A Physicochemical and Engineering Aspects

Understanding the Mechanism of Poly(3-Hexylthiophene)-B-Poly(4-Vinylpyridine) As A Nanostructuring Compatibilizer for Improving the Performance of Poly(3-Hexylthiophene)/Zno-Based Hybrid Solar Cells

Interface Engineering of High Efficiency Perovskite Solar Cells Based on ZnO Nanorods Using Atomic Layer Deposition

Enhanced Performance of Polymer Solar Cell with Zno Nanoparticle Electron Transporting Layer Passivated by in Situ Cross-Linked Three-Dimensional Polymer Network

Hybrid polymer/zinc oxide photovoltaic devices with vertically oriented ZnO nanorods and an amphiphilic molecular interface layer

Controlling Morphology and Improving the Photovoltaic Performances of P3ht/Zno Hybrid Solar Cells Via P3ht-B-Peo As an Interfacial Compatibilizer

Interfacial Engineering of Zno Nanoarrays As Electron Transport Layer for Polymer Solar Cells

Light Harvesting and Carrier Transfer Enhancement of All-Inorganic CsPbBr3 Perovskite Solar Cells by Al-doped ZnO Nanorod Arrays

Hybrid Polymer-Cdse Solar Cells with A Zno Nanoparticle Buffer Layer for Improved Efficiency and Lifetime

Fabrication of Ordered One-Dimensional P3ht/Cds/Tio2/Zno Core-Shell Nanorod Array and Their Application to Hybrid Solar Cell