Abstract:Lightweighting in ground vehicles is considered as one of the most effective strategies to improve fuel economy and reduce anthropogenic environment-damaging, climate-changing and costly emissions. Magnesium (Mg) alloy, as a strategic ultra-lightweight metallic material, has recently drawn a considerable interest in the transportation industry to reduce the weight of vehicles due to their high strength-to-weight ratio, dimensional stability, and good machinability and recyclability. However, the hexagonal close-packed crystal (HCP) structure of Mg alloys gives only limited slip systems and develops sharp crystallographic textures associated with strong mechanical anisotropy and tension-compression yield asymmetry. For the vehicle components subjected to dynamic loading, such asymmetry could exert an unfavorable influence on the material performance. These problems could be tackled through texture modification via addition of rare-earth (RE) elements. These RE-Mg alloys possess relatively weak initial textures, which lead to improved ductility and strength, and a reduction of the tension-compression asymmetry present in the conventional wrought Mg alloys. Despite the fact that the addition of RE elements sheds some light on the alterations in the mechanical anisotropy and the tension-compression yield asymmetry, the potential advantage of such RE-Mg alloys as structural components under cyclic loading condition has not been well appreciated. Thus, the main objective of this dissertation was to explore the cyclic deformation behavior of RE-Mg alloys under varying strain amplitudes and strain ratios, and correlate the behavior to the microstructural change and crystallographic texture weakening in the RE-Mg alloys in different states (extruded and heat-treated). Unlike the RE-free Mg alloys, these alloys exhibited essentially cyclic stabilization and fairly symmetrical hysteresis loops due to the weaker texture and reduced twinning-detwinning activities. While these alloys had a lower cyclic strain hardening exponent than the RE-free extruded Mg alloys, it had a longer fatigue life which can also be described by the Coffin-Manson law and Basquin’s equation. Fatigue crack was observed to initiate from the specimen surface with some cleavage-like facets near the initiation site. Crack propagation was basically characterized by fatigue striations in conjunction with secondary cracks. A detailed analysis for understanding the obstructive role of the precipitate to twinning has been also presented.

Experimental and Theoretical Study of the Cyclic Relaxation of Die Cast Magnesium Alloy

Mean Stress Relaxation During Low-cycle Fatigue of Aluminum Alloy 7050-T7451

Cyclic Deformation Behaviour and Potential Automobile Application of Magnesium Die Casting Alloys AZ91 and AM50

A Cyclic Stress-Strain Constitutive Model for Polycrystalline Magnesium Alloy and its Application

Influence of Strain Rate and Stress State on the Mechanical Behavior of Die-Casting AM60 Magnesium Alloy

Cyclic Deformation Behavior of a High Zinc-Containing Cast Magnesium Alloy

Investigation on Mechanical Behaviour of AM60 Magnesium Alloys

Study on Plastic Constitutive Relation and Ductile Fracture Criterion of AM60B Magnesium Alloy

Low-Cycle Fatigue Behavior of Magnesium Alloy AZ91

Ratcheting and Low Cycle Fatigue Behavior of AZ91D at Room Temperature

Strain-controlled cyclic deformation behavior of cast Mg–2.99Nd–0.18Zn–0.38Zr and AZ91D magnesium alloys

Influence of Heat Treatment on Cyclic Deformation and Low-Cycle Fatigue Behavior of Sand-Cast Mg–10Gd–3Y–0.5Zr Magnesium Alloy

Cyclic deformation behavior of rare-earth containing magnesium alloys

Effects of Extrusion Ratio on the Ratcheting Behavior of Extruded AZ31B Magnesium Alloy under Asymmetrical Uniaxial Cyclic Loading

Low Cycle Fatigue Behavior of the Extruded AZ80 Magnesium Alloy under Different Strain Amplitudes and Strain Rates

Deformation Behaviors and Cyclic Strength Assessment of AZ31B Magnesium Alloy Based on Steady Ratcheting Effect

Cyclic Plasticity Constitutive Model for Uniaxial Ratcheting Behavior of AZ31B Magnesium Alloy

Cyclic hardening behavior of extruded AZ31B magnesium alloy during low cycle fatigue process

A New Constitutive Model for Thermal Deformation of Magnesium Alloys

Low cycle fatigue of a rare-earth containing extruded magnesium alloy