Abstract:It is well-known that distinct vapor plume dynamics occur during deep penetration laser welding under different keyhole penetration states. However, there is little knowledge about the physical characteristics of vapor plumes (velocity, pressure, flow patterns, etc)located inside transient keyholes of varying penetration regimes in laser welding. This lack of knowledge is primarily because mesoscale vapor plumes are highly dynamic and generally invisible. Based on a well-tested three-dimensional multiphase laser welding model, we conducted a computational study on vapor plume dynamics inside transient keyholes during the fiber laser welding of 304 austenite stainless steel as a function of keyhole penetration regimes. We observed three keyhole regimes of penetration: full penetration, partial penetration and no penetration. We then physically analyzed the vapor plumes in these regimes. We determined that the vapor plume velocities and pressures in all three regimes were uneven and oscillated following the dynamic keyhole with a characteristic timescale in sub-microseconds. Only when the keyhole approached the full penetration regime did vapor plumes begin to violently eject from the bottom of the keyhole opening, whereas in the partial penetration regime, even when the bottom part of the keyhole was open, most of the vapor plume ejected from the upper keyhole opening. This latter observation was similar to that in the no penetration mode. We studied the physical mechanism of this behavior by analyzing the keyhole temperature and vapor plume velocity distributions. We determined that the upward ejection of the vapor plume from the upper keyhole opening was the result of an uneven micro-meter scale boiling phenomenon of the transient keyhole governed by Fresnel absorptions dependent on the local inclination angle of the keyhole wall. Similarly, we determined that the ejection of the vapor plume from the bottom of the keyhole opening resulted from pressure differences between the inside and outside of the keyhole ( as long as there was a relatively stable open state at the bottom of the keyhole opening). Additionally, we conducted quantitative studies on the velocity and pressure of vapor plumes in transient keyholes for all three regimes. We observed a decrease in the average velocity of vapor plumes at the upper keyhole opening, and an increase in average velocity at the bottom opening when the penetration regime moved from no penetration to full penetration. Moreover, the pressure distributions of vapor plumes decreased and became more uniform as the penetration regime varied from no penetration to full penetration. For the investigated process parameters used for the fiber laser welding of 1 mm thick 304 stainless steel, the vapor plume pressure decreased approximately 500-1200 Pa inside the millimeter scale keyhole. The findings in this study give the first physical insights into vapor plume dynamics inside transient keyholes as a function of keyhole penetration states during deep penetration laser welding. Moreover, our findings can be used as theoretical references for welding process parameter optimization in industrial applications.

Spectroscopic measurements of plasma inside the keyhole in deep penetration laser welding

Direct observation of keyhole characteristics in deep penetration laser welding with a 10 kW fiber laser.

Plasma Inside and Outside Keyhole During 10 Kw Level Fiber Laser Welding

Sub-microsecond vapor plume dynamics under different keyhole penetration regimes in deep penetration laser welding

Dynamic Characteristics and Mechanisms of Compressible Metallic Vapor Plume Behaviors in Transient Keyhole During Deep Penetration Fiber Laser Welding

Influence mechanism of the keyhole behavior on penetration depth by in-situ monitoring in pulsed laser welding of aluminum alloy

Simulation of Photoinduced Plasma Behavior in Laser Penetration Welding

Dynamic keyhole profile during high-power deep-penetration laser welding

Dynamics of Vapor Plume in Transient Keyhole During Laser Welding of Stainless Steel: Local Evaporation, Plume Swing and Gas Entrapment into Porosity

Numerical analysis of the effect of an oscillating metal vapor plume on the keyhole and molten pool behavior during deep penetration laser beam welding

Observation of spatter formation mechanisms in high-power fiber laser welding of thick plate

A study on laser keyhole welding in vacuum by computational fluid dynamics simulations with plume effect models

Recent Advance in Research for Keyhole Behavior During Laser Deep Penetration Welding Process

Fundamental understanding of open keyhole effect in plasma arc welding

Frontal pyrometric snapshot measurements of the keyhole wall temperature in laser welding of pure aluminium

Correlation Between Gas-Dynamic Behaviour of a Vapour Plume and Oscillation of Keyhole Size During Laser Welding of 5083 Al-alloy

Prediction of the laser-induced plasma characteristics in laser welding: a new modelling approach including a simplified keyhole model

Mechanism, Modeling, and Application of Plasma Current in Deep-Penetration Laser Welding

Plasma light emission monitoring and penetration status recognition in CO2 laser welding of AZ31B wrought magnesium alloy - art. no. 682502

Experimental and Numerical Analysis of Molten Pool and Keyhole Profile During High-Power Deep-Penetration Laser Welding

Effect of Electric Arc on Laser Keyhole Behavior Based on Direct Observation During Low Power Pulsed Laser–arc Hybrid Welding Process