Discussion on Soil Shrinkage Characteristic Curves

YANG Shao-e,HUANG Yuan-fang

DOI: https://doi.org/10.3321/j.issn:0564-3945.2007.04.028

2007-01-01

Abstract:We Introduced a model for soil shrinkage characteristic curve,which was produced by Groenevelt and Grant,and promoted an idea for this model.

What problem does this paper attempt to address?

Influences Affecting the Soil-Water Characteristic Curve

Zhou Jian,Yu Jian-lin

DOI: https://doi.org/10.1631/jzus.2005.a0797

2005-01-01

Abstract:The soil-water characteristic curve (SWCC) is the primary partially saturated soil information as its behavior and properties can be derived from it. Although there have been many studies of unsaturated soils and the SWCC, there is still no combined constitutive model that can simulate soil characteristics accurately. In cases when hydraulic hysteresis is dominant (e.g.under cyclic loading) it is particularly important to use the SWCC. In the past decades, several mathematical expressions have been proposed to model the curve. There are various influences on the SWCC as a source of information, so the curves obtained from conventional tests often cannot be directly applied;and the mathematical expressions from one scenario cannot be used to simulate another situation. The effects of void ratio, initial water content, stress state and high suction were studied in this work revealing that water content and stress state are more important than the other effects;but that the influences tend to decrease when suction increases. The van Genuchten model was modified to simulate better the changes in the degree of saturation at low values of suction. Predictions were compared with experimental results to determine the simulation capability of the model.
RESEARCH ON PATTERN TRANSITION CURVES AND THE PARAMETERS IN STRESS-STRAIN RELATIONSHIP OF SOILS

Bin HUANG,Ri-qing XU,Jing-chun WANG

DOI: https://doi.org/10.3969/j.issn.1001-6864.2006.01.025

2006-01-01

Abstract:The stress-strain relationship of soil established from triaxial shear test is distinguished into two kinds—hardening type and post-peak softening type. A unified mathematical expression is presented to describe the two types of stress-strain relationship and the meaning of parameters in the expression is given. Then based on the stress-strain relationship and considering the preconsolidation pressure P_c a combined model for describing the pattern transition in stress-strain relations of clay in Hangzhou is schematically suggested. And point out that initial tangential modulus is relative to the preconsolidation pressure P_c.
Macro- and Meso-Scale Parametric Analysis of Egg-shaped Yield Surface of Structural Soil

Ri-qing Xu,Xing-chen Wang,Xue-ning Rong

2014-01-01

International Journal of Offshore and Polar Engineering

Abstract:A comparative study of the types of yield surfaces was conducted. It was found that the egg-shaped yield surface, as a closed yield surface, compensates for the defects of the open and cap yield surfaces. A theoretical analysis was then performed to determine the egg-shaped yield surface parameters of soil material. The concept of initial plastic modulus was proposed, and the relationships between parameters a, b, and d of the egg-shaped yield function and the initial plastic modulus were established. The soil shear wave velocity, which is a meso-scale parameter, was also introduced to establish the relationships among the parameters. Parameter a was determined based on the consistency of the value between shape parameter a and the tangent function of the internal friction angle. To confirm the rationality of the theoretical analysis, silty clay was mixed with cement to prepare artificial structural clay. The shear wave velocity (based on the bender element), isotropic compression, conventional triaxial compression, and stress path compression tests were conducted. The initial yield characteristics of the soil at different cementing strengths were determined. Regression analysis was performed by using the egg-shaped yield function, which quantitatively indicated the correlations between the initial shear wave velocity, peak internal friction angle, and egg-shaped yield surface parameters. The parameter determination method accurately reflected the physical properties of soil and exhibited excellent practicability by combining the macro- and meso-scales.
A fractal-based soil - Water characteristic curve model for unsaturated soils

Jingyu Chen,Xiaonan Gong,MingYuan Wang

DOI: https://doi.org/10.1061/40860(192)3

2006-01-01

Abstract:Recently, a new soil-water characteristic curve model for unsaturated soils was proposed based on a fractal model for the soil pore surface. The air-entry value and the surface fractal dimension of soil pores were used to determine the soil-water characteristic curve in this new fractal-based soil-water characteristic curve model. The experimental results found from literature can testify the new model. The new experiment on unsaturated loess is conducted to compare with the new model. The soil-water characteristic curve drawn with experiment data is in satisfactory agreement with the curve predicted by the new model. Copyright ASCE 2006.
Experiment And Modeling Of Soil-Water Characteristic Curve Of Unsaturated Residual Soil

Chen Dong-Xia,Gong Xiao-Nan

DOI: https://doi.org/10.16285/j.rsm.2014.07.010

2014-01-01

Rock and soil mechanics

Abstract:The soil-water characteristic curve (SWCC) is defined as the relationship between the suction and the water content or degree of saturation. The soil-water characteristics and related mathematical models can be used to model the unsaturated soil properties such as the permeability and the shear strength. Conventionally, only the drying soil-water characteristic curve of soil is determined. In this work, the influences of initial water content, initial dry density, the vertical stress and drying and wetting cycles are examined and discussed in detail. The SWCCs and hysteresis loops of residual soils in Xiamen were obtained by the filter paper method. The results show that the initial water content has negligible effect on SWCCs. The specimen at the wet of optimum moisture content (OMC) has the higher air entry value and the larger hysteresis loop than that of the soil specimen at the dry of OMC. The specimen with OMC lies between them. While, the initial dry density has considerable influence on SWCCs. The specimen at lower initial dry density exhibits smaller air entry value and higher rate of desorption than that of the specimen at higher initial dry density. The size of hysteresis loop decreases as the initial dry density increases. The specimens subjected to different vertical stresses have different SWCCs. The higher the applied load on the specimen, the higher the air entry value, the higher the rate of desorption, the smaller the size of hysteresis loop. In the drying and wetting process, the size of hysteresis loop has been substantially affected by the first drying and wetting cycle. With the increasing of drying and wetting cycle, the air entry value and the size of hysteresis hoop decrease. Since the features of soil-water characteristic of sandy clay are not well defined especially for the residual state of saturation, which desaturates continuously without a distinct break point, the residual suction or residual water content, one of the key parameters in the mathematical models of SWCC, is not well defined. As a result five improved models without the residual water content are proposed to describe the SWCCs of residual soil. The improved Gardner model has been found to be the most suitable model for all SWCCs of the residual sandy clay in Xiamen.
The soil reference shrinkage curve

V. Y. Chertkov

DOI: https://doi.org/10.2174/1874378100701010001

2014-03-12

Abstract:A recently proposed model showed how a clay shrinkage curve is transformed to the soil shrinkage curve at the soil clay content higher than a critical one. The objective of the present work was to generalize this model to the soil clay content lower a critical one. I investigated (i) the reference shrinkage curve, that is, one without cracks; (ii) the superficial layer of aggregates, with changed pore structure compared with the intraaggregate matrix; and (iii) soils with sufficiently low clay content where there are large pores inside the intraaggregate clay (so-called lacunar pores). The methodology is based on detail accounting for different contributions to the soil volume and water content during shrinkage. The key point is the calculation of the lacunar pore volume variance at shrinkage. The reference shrinkage curve is determined by eight physical soil parameters: (1) oven-dried specific volume; (2) maximum swelling water content; (3) mean solid density; (4) soil clay content; (5) oven-dried structural porosity; (6) the ratio of aggregate solid mass to solid mass of intraaggregate matrix; (7) the lacunar factor that characterizes the rate of the lacunar pore volume change with water content; and (8) oven-dried lacunar pore volume. The model was validated using available data. The model predicted value of the slope of the reference shrinkage curve in the basic shrinkage area is equal to unity minus the lacunar factor value, and is between unity and zero in the agreement with observations.

Geophysics,Soft Condensed Matter
Physical modeling of the soil swelling curve vs. the shrinkage curve

V. Y. Chertkov

DOI: https://doi.org/10.48550/arXiv.1404.3506

IF: 3.264

2014-04-14

Geophysics

Abstract:Physical understanding of the links between soil swelling, texture, structure, cracking, and sample size is of great interest for the physical understanding of many processes in the soil-air-water system and for applications in civil, agricultural, and environmental engineering. The background of this work is an available chain of interconnected physical shrinkage curve models for clay, intra-aggregate matrix, aggregated soil without cracks, and soil with cracks. The objective of the work is to generalize these models to the case of swelling, and to construct the physical-swelling-model chain with a step-by-step transition from clay to aggregated soil with cracks. The generalization is based on thorough accounting for the analogies and differences between shrinkage and swelling and the corresponding use, modification, or replacement of the soil shrinkage features. Two specific soil swelling features to be used are: (i) air entrapping in pores of the contributing clay; and (ii) aggregate destruction with the formation of new aggregate surfaces. The input for the prediction of the swelling curve of an aggregated soil coincides with that of the available model of the shrinkage curve. The analysis of available data on the maximum shrink-swell cycle of two soils with different texture and structure, accounting for sample size is conducted as applied to swelling curves and to the residual crack volume and maximum-swelling-volume decrease after the shrink-swell cycle. Results of the analysis show evidence in favor of the swelling model chain.
Behavior Of Expansive Soil Slope Reinforced With Geo-Grids

M. Y. Wang,X. N. Gong,M. Y. Wang,J. T. Cai,H. Xu

DOI: https://doi.org/10.1201/9780203885284-c228

2008-01-01

Abstract:In recent years, "expansive soil slope reinforced with geogrids" has been successfully applied in some projects in China, but there is lack of study on its engineering behavior. An ideal elastoplastic constitutive law is utilized to model the interaction between geogrid and expansive soil based on the pullout test. Behavior of slope reinforced with geogrids under moisture absorption condition of unsaturated expansive soils is analyzed adopting the finite difference method. The strength reduction method based on stress state is used to analyze the stability of slope reinforced with geogrids and study the restraint effect of geogrids on the shallow failure of expansive soil slope due to long-term weathering. Results show that the greater the elastic modulus of geogrids, the more obvious its restraint effect on the deformation due to moisture absorption of unsaturated expansive soil slope. The shallow failure of expansive soil slope can be effectively restrained by reinforced geogrids.
Study on the Strength of Expansive Soil Based on Water Content and Dry Wet Cycle

Sheng-jie RUI,Xiao-lan CHEN,Qing-hua LIU,Qi YANG

DOI: https://doi.org/10.3969/j.issn.1671-1815.2017.25.047

2017-01-01

Abstract:The effect of different water content and constant-amplitude dry wet cycle on the strength of Fuyang expansive soil was studied by using the conventional indoor direct shear test.The experimental results were explained and the fitting curve was obtained,and the development of cracks in the process of dry and wet cycle was analyzed.The experimental results show:the water content and the wet-dry cycle have important effects on the strength of expansive soil.The shear strength index c,φ has a good linear relationship with the water content.The strength index has a good exponential relationship with circle times.The strength of the soil is gradually close to the residual strength after several dry wet cycles.The development of the fracture is the main reason for the decrease of the strength of the expansive soil under the wet dry cycle.The fractures destroy the structure of the soil and make the cohesive force decrease.So that the frictional force is reduced.The opening of the fissure causes the bite friction force to decrease.
Analysis of soil drying incorporating a constitutive model for curling

Michael Maedo,Marcelo Sánchez,Duaa Aljeznawi,Osvaldo Manzoli,Leonardo J. N. Guimarães,Pedro Rogério Cleto

DOI: https://doi.org/10.1007/s11440-020-00920-0

2020-03-06

Acta Geotechnica

Abstract:This paper focuses on the shrinkage behavior of soil specimens involving sand, kaolinite, and kaolinite/sand mixtures subjected to desiccation under controlled conditions. Both, free and restrained shrinkage conditions are studied. The experiments show that pure soils do not curl upon unrestrained shrinkage; however, (under the same conditions) kaolinite/sand mixtures exhibited a marked curling. Furthermore, the mixture with the higher sand content broke through the middle of the sample after displaying a significant curling. Soils subjected to restricted shrinkage developed cracks with slight curling. To simulate the observed behavior, a mechanical model able to reproduce the detachment of the soil sample from the mold is proposed in this work and implemented in a fully coupled hydro-mechanical finite-element code. It is concluded that suction and differential shrinkage are key factors influencing the curling behavior of soils. The proposed framework was able to satisfactorily explain and reproduce the different stages and features of soil behavior observed in the experiments.

engineering, geological
The physical effects of an intra-aggregate structure on soil shrinkage

V. Y. Chertkov

DOI: https://doi.org/10.48550/arXiv.1403.7918

IF: 3.264

2014-03-31

Geophysics

Abstract:Clay and soil containing it have shrinkage curves that are qualitatively different in shape. The objective of this work is to qualitatively show with maximum simplicity, how a clay shrinkage curve turns into a soil shrinkage curve. Because of the crack volume the measured shrinkage curve is not the single-valued feature of a soil. We use a concept of the reference shrinkage curve that is only stipulated by soil shrinkage without cracking, single-valued, and qualitatively similar to an observed shrinkage curve. We also use new concepts of an intra-aggregate soil structure: (i) a rigid superficial layer of aggregates that loses water during shrinkage; and (ii) lacunar pores (micro-cracks) inside an intra-aggregate clay that change in volume during shrinkage. Then, through a series of consecutive steps, illustrating each step by a separate graphic presentation, we move from a clay shrinkage curve to a soil shrinkage curve with predicted qualitative features that coincide with those experimentally observed in numerous soil shrinkage publications. We thereby demonstrate the qualitative physical impact of the intra-aggregate structure on soil shrinkage.
An integrated approach to soil structure, shrinkage, and cracking in samples and layers

V. Y. Chertkov

DOI: https://doi.org/10.48550/arXiv.1404.1696

IF: 3.264

2014-04-07

Geophysics

Abstract:A recent model showed how a clay shrinkage curve is step-by-step transformed into the shrinkage curve of an aggregated soil at any clay content if it is measured on samples so small that cracks do not occur at shrinkage. Such a shrinkage curve was called a reference curve. The present work generalizes this model to any soil sample size or layer thickness, i.e., to any crack contribution to the shrinkage curve. The approach is based on: (i) recently suggested features of an intra-aggregate structure; (ii) detailed accounting for the contributions to the soil volume and water content during shrinkage; and (iii) new concepts of lacunar factor, crack factor, and critical sample size. The following input parameters are needed for the prediction: (i) all parameters determining the basic dependence of the reference shrinkage curve; (ii) parameters determining the critical sample size (structural porosity and minimum and maximum aggregate size at maximum swelling); and (iii) initial sample size or layer thickness. A primary experimental validation of the new model concepts is conducted using the relevant available data on the shrinkage curves of four soils with different texture and structure that were obtained utilizing the samples of two essentially different sizes. The results show evidence in favor of the model.
Experiment and Modeling of Soil-Water Characteristic Curve of Unsaturated Soil in Collapsing Erosion Area

Weiping Liu,Xiaoyan Luo,Mingfu Fu,Jinsong Huang

DOI: https://doi.org/10.15244/pjoes/64307

2016-01-01

Polish Journal of Environmental Studies

Abstract:Soil erosion tends to occur with rainfall runoff, thus leading to grave soil and water loss. An increase of water content in soil caused by rain makes the loss of matrix suction and the decrease of shear strength obvious, and will promote soil erosion. The soil-water characteristic curve (SWCC) can be used to describe the relationship between the water content and the matrix suction in unsaturated soil. For this paper we studied the SWCCs of the granite residual soils in a collapsing erosion area in Jiangxi Province, China. A GEO-Experts pressure plate extractor was used to measure SWCCs for soils with different dry density, grain size, drying and wetting cycles, and lime content. The initial dry density has a significant impact on SWCC. With increasing dry density, the suction was decreased for the same water content. The larger the grain size, the greater the suction value for the same volumetric water content. Under the same suction, the volumetric water content decreases as the lime percentage increases and water stability improves. SWCCs of the drying and wetting cycle demonstrate the hysteresis phenomenon. The area of the hysteresis loop decreased with the increase of the dry density and drying and wetting cycle number. It also became small when the soils were mixed with lime. In this paper, the Van Genuchten model, the Fredlund and Xing model, and the Gardner model were used to fit the experimental data of SWCCs. The presented fitting parameters show that the residual sum of squares is less than 0.002. All the experimental data fit well to three models for SWCC. The results indicated that the simulated value of the Gardner model does provide best agreement with the measured value. These results will provide an important basis for the further study of the soil collapsing erosion process and soil cover design.
Preliminary Study on the SwellingDeformation of Some Expansive Soils

Xu Yongfu

1997-01-01

Abstract:Based on the testing of swelling deformation of expansive soils, a model on the swelling deformation is presented in this paper. By using this model, the characteristics of sweling deformation can be inter- preted.
Seepage test and empirical models for soils based on GDS apparatus

邹圣锋,李金柱,王忠瑾,兰璐,王文军,谢新宇

DOI: https://doi.org/10.3785/j.issn.1008-973X.2017.05.003

2017-01-01

Abstract:In order to reveal the seepage characteristics of Ningbo marine soft clay under various hydraulic gradient,confining pressure and void ratio,eight series of constant head seepage tests were performed on both undisturbed and remolded soil samples utilizing the GDS apparatus.Fitting study of the widely used seepage models in academic field was conducted by the test results.It is shown that seepage coefficients of test samples decrease nonlinearly with decreasing void ratio,which behave more obviously on remolded soil samples.Similar seepage behaviors were obtained from both remolded and undisturbed soils as well,and the test results agreed well with fitting lines of the four existing seepage models.A new nonlinear empirical model was proposed,and test data of ten kinds of soils were collected to investigate its rationality and applicability.The comparison research on fitting results shows that the new model is better used than four existing seepage models,and the application of this new model turns to worth further research.
Volumetric shrinkage characteristics of soil during drying

TANG Chao-sheng,CUI Yu-jun,SHI Bin

2011-01-01

Abstract:Drying shrinkage is one of the intrinsic characteristics of soil,and has profound effects on its engineering properties.In this investigation,laboratory tests are conducted on initially saturated paste-like specimens and compacted specimens with different compaction parameters.For the paste-like specimens,the fluid volume displacement technique is employed to measure the volumetric change of specimens during drying,and the complete shrinkage curve is determined.It is found that three stages can be distinguished in the shrinkage of paste-like specimens,namely normal shrinkage,residual shrinkage and zero shrinkage;most of the volumetric shrinkage deformation occurs before the air-entry point while the soil is still fully saturated;the volume shrinkage behavior and shrinkage curve shape significantly depend on soil microstructure characteristics.For the compacted specimens,the shrinkage behavior is significantly controlled by the initial drying density and water content.In general,shrinkage strain decreases with the increase of the initial dry density and increases with the increase of the compaction water content.In addition,the results show that the shrinkage of compacted specimens is anisotropic rather than isotropic,and is more sensitive to the initial water content than the initial dry density.A coupled linear and exponential equation is finally developed from the obtained data to describe the shrinkage strain at the given initial drying density and water content.
A soil freezing characteristic curve model for capturing void ratio and specific surface area effects

Zhang Ji-wen,Mu Qing-yi,Liao Hong-jian,Liu Fen-liang

DOI: https://doi.org/10.16285/j.rsm.2019.1982

2020-01-01

Rock and soil mechanics

Abstract:Soil freezing characteristic curve (SFCC) defines the relationship between temperature and unfrozen water content. SFCC plays an important role in estimating strength and deformation behavior of frozen soil as well as heat-water transfer in frozen soil. In this work, a new model for SFCC is proposed by explicitly considering capillarity and adsorption. The freezing of pore water is assumed to be dominated by capillarity (i.e., 0 similar to-2 degrees C) and adsorption (i.e., <-2 degrees C) at high and low temperatures, respectively. The capillarity and adsorption are controlled by soil void ratio and specific surface area, respectively. Extensive experimental data found in the literature (i.e., SFCC with different void ratios; SFCC at wide temperature range; SFCC with different soil specific surface areas) are used to validate the newly proposed model. Three existing models are also adopted to compute the experimental data. Comparisons of the computed results show that only the newly proposed model can capture the void ratio dependent SFCC with one series of parameter. On the other hand, the newly proposed model performs better in computing SFCC at a wide temperature range and those SFCCs with high specific surface areas than those existing models.
Fractal Characteristics And Fitting Analysis Of Soil-Water Characteristic Curves

Tao Gao-Liang,Kong Ling-Wei,Xiao Heng-Lin,Ma Qiang,Zhu Zhi-Zheng

DOI: https://doi.org/10.16285/j.rsm.2014.09.028

2014-01-01

Rock and soil mechanics

Abstract:In order to establish a fitting approach for soil-water characteristic curves (SWCC) with clear physical meanings, a method is presented to directly calculate the fractal dimensions through the SWCC data based on the fractal theory, and a fractal model of SWCC is proposed. To verify the proposed fitting method, seven clay samples with different dry densities are prepared using hydraulic jacks, and the soil-water characteristic curves are measured by using the pressure plate apparatus. Based on the experimental results of SWCC, the fractal dimensions are calculated. On this basis, fitting analysis of the SWCC data is performed by using the presented method. The results show that, all the correlation coefficients of the seven samples range from 0.97 to 0.99, which indicates good fractal characteristics of SWCC as well as good fitting performance of the proposed method. In addition, it is found that the fractal dimensions and the air entry values increase almost linearly with the dry density. On this basis, a prediction method of SWCC at different compaction degrees is also proposed and tested. The prediction results are in good agreement with the measured values.
A family of soil water retention models based on sigmoid functions

Peijun Li,Yuanyuan Zha,Bingxin Zuo,Yonggen Zhang

DOI: https://doi.org/10.1029/2022WR033160

IF: 5.4

2023-03-12

Water Resources Research

Abstract:The soil water retention curve is the fundamental soil hydraulic property to characterize soil water movement and solute transport. Many efforts have been devoted in the past decades to developing models to describe soil water retention curves. However, most of them are empirical equations or assume that soil pore size distributions conform to a lognormal distribution. Yet, few effects have been undertaken to systematically propose and compare a series of possible alternative probability density functions to describe the sigmoid retention curves with parameters physically explainable. Here, we proposed a family of five soil water retention models based on sigmoid functions with parameters of clear physical implications coinciding with the statistical measures of soil pore size distribution. Compared with the widely‐used models (i.e., Brooks and Corey (1964), van Genuchten (1980), and Kosugi (1996)), the proposed models have somewhat improved performances to characterize water retention data for a wide range of soil textures without introducing additional model parameters. Two of the proposed models are capable of characterizing the observed two local extrema in the moisture capacity curves. The associated unsaturated hydraulic conductivity models of the proposed soil water retention models are also derived, which show superior performance in characterizing the observed hydraulic conductivities compared with competing models, especially in macropore regimes. Additionally, we analyzed the parameter‐equivalent conversion between the proposed and the existing models, and a simple linear regression equation can be used to derive the parameters of the proposed models from the existing and other alternative different proposed models. This article is protected by copyright. All rights reserved.

environmental sciences,water resources,limnology
A graph-based approach for modeling the soil–water retention curve of granular soils across the entire suction range

Wei Yan,Ludwig Angerer,Emanuel Birle,Roberto Cudmani

DOI: https://doi.org/10.1007/s11440-023-02166-y

2024-02-27

Acta Geotechnica

Abstract:This study investigates experimentally the water retention behavior of granular soils from saturation to oven-dry state. The soil–water retention curve (SWRC) tests were conducted on a well-graded sand with clay using tensiometer and chilled-mirror hygrometer techniques. The soil samples were statically compacted at various water contents to different initial densities. The results showed that individual linear segments in the log–log graph could characterize the desorption process of capillary and adsorption water. A novel water retention model in a simple mathematical form was developed by conceptualizing the total water content as the sum of the suction-dependent capillary and adsorption components. The model parameters possess an unambiguous physical meaning. They can be easily calibrated based on the graphical properties of the test data using simple linear regression, which is a significant advantage over conventional SWRC models. The model was validated using the water retention data of the tested soil in this study and the available data of granular soils in the literature. The reproduced curves agree well with the experimental results. This study also analyzed the influence of compaction water content, initial density, and clay content on the capillary and adsorption components of the water retention curve. Additionally, the proposed framework provides a quick approximation method for the adsorption capacity, which plays an essential role in assessing the effective stress and the simulation of liquid film flow in unsaturated granular soils.

engineering, geological

Discussion on Soil Shrinkage Characteristic Curves

Influences Affecting the Soil-Water Characteristic Curve

RESEARCH ON PATTERN TRANSITION CURVES AND THE PARAMETERS IN STRESS-STRAIN RELATIONSHIP OF SOILS

Macro- and Meso-Scale Parametric Analysis of Egg-shaped Yield Surface of Structural Soil

A fractal-based soil - Water characteristic curve model for unsaturated soils

Experiment And Modeling Of Soil-Water Characteristic Curve Of Unsaturated Residual Soil

The soil reference shrinkage curve

Physical modeling of the soil swelling curve vs. the shrinkage curve

Behavior Of Expansive Soil Slope Reinforced With Geo-Grids

Study on the Strength of Expansive Soil Based on Water Content and Dry Wet Cycle

Analysis of soil drying incorporating a constitutive model for curling

The physical effects of an intra-aggregate structure on soil shrinkage

An integrated approach to soil structure, shrinkage, and cracking in samples and layers

Experiment and Modeling of Soil-Water Characteristic Curve of Unsaturated Soil in Collapsing Erosion Area

Preliminary Study on the SwellingDeformation of Some Expansive Soils

Seepage test and empirical models for soils based on GDS apparatus

Volumetric shrinkage characteristics of soil during drying

A soil freezing characteristic curve model for capturing void ratio and specific surface area effects

Fractal Characteristics And Fitting Analysis Of Soil-Water Characteristic Curves

A family of soil water retention models based on sigmoid functions

A graph-based approach for modeling the soil–water retention curve of granular soils across the entire suction range