Abstract:Objective: To investigate the rotational variations of three-dimensional (3D) trajectories at anatomic landmarks by different mandibular kinematics, we applied principal axes of inertia to the 3D trajectories. The principal rotations were determined directly from the anatomy-based trajectories produced by a patient-specific temporomandibular joint simulation. As a preliminary study, the principal rotations for a pilot group of patients with mandibular deviation were correlated with the deviation. Study design: Three-dimensional mandibular movements from the patients with mandibular deviation were tracked based on a patient-specific splint and an optical tracking system. The dental occlusion recorded on the splint provided synchronization for initial movement in the tracking and the simulation phases. The translation and rotation recorded during tracking were applied sequentially to the mandibular model in relation to a fixed maxilla model. The sequential positions of the points of interest based on the reference coordinate system could also be simulated and traced by the same method. The landmarks selected for analysis were the points of the bilateral condyles and of the mandibular incisor. The moment of inertia tensor was calculated with respect to the 3D trajectory points. Using the unit vectors along the principal axes derived from the tensor matrix, α, β, and γ rotations (horizontal, sagittal, and frontal planes) around the z-, y-, and x-axes, respectively, were determined to represent the principal directions as principal rotations. Results: The measured rotations were correlated with the deviation in 3 orthogonal planes. Under the influence of the mandibular asymmetry, the orientations of the principal axis at the condyles increase counterclockwise in the horizontal plane and clockwise in the frontal plane. At the incisor point, the horizontal and frontal angles increase counterclockwise, but the sagittal angles increase clockwise. The interrelations between different rotations and between landmarks, defined as a correlation coefficient between principal rotations, decrease as the deviation increases. Conclusions: Three-dimensional trajectories at selected landmarks based on the reference coordinate system were evaluated using principal axes of inertia to investigate the functional characteristics of the mandible with a deviation. The movement asymmetry between the condyles increases as the deviation increases in all directions. The principal rotations at the condyles can be explained by those at the incisor with varying degrees despite the deviation.

Inferior orbitaljissure method: A novel approach for detecting mandibular deviation degree

Simultaneous correction of bilateral temporomandibular joint ankylosis with mandibular micrognathia using internal distraction osteogenesis and 3-dimensional craniomaxillofacial models.

Evaluation of the accuracy of a fully digital method of measuring sagittal condylar inclination

A comparative study to measure the sagittal condylar inclination using mechanical articulator, virtual articulator and jaw tracking device

Automated Photographic Analysis of Inferior Oblique Overaction Based on Deep Learning.

An innovative evaluation method for clinical comparative analysis of occlusal contact regions obtained via intraoral scanning and conventional impression procedures: a clinical trial

[A correlation study between the occlusal cant and temporomandibular joint space in patients with mandibular lateral deviation]

The Comparative Study of Vertical Cephalometric Index of Angle I Malocclusion

Developing a universal and reliable temporomandibular joint reference system for quantifying morphological and positional changes

A study on the precision of voxel- and surface-based mandibular superimposition

The relationship between three-dimensional principal rotations and mandibular deviation

Comparison of Measurement in the Ocular Region between the Direct Measurement and Photogrammetry

Correlation study on the morphology of spine coronal plane and trunk balance in adult patients with mandibular deviation

Comparative Study of Mandible and Temporomandibular Joint in Adults with and Without Mandibular Deviation Using SPECT/CT Fusion Imaging

Regional 3D superimposition to assess temporomandibular joint condylar morphology

In vivo evaluation of the reliability and validity of three digital occlusion analysis methods

Comparative analysis of three jaw motion tracking systems: A study on precision and trueness

Evaluating sagittal condylar inclination: a comparative analysis of various digital workflow measures

Use of a Microelectromechanical Systems Sensor for Objective Measurements of Abnormal Head Posture in Congenital Superior Oblique Palsy Patients

Study on the use of temporomandibular joint dysfunction index in temporomandibular disorders.

[Radiographic Study on Joint Space Changes of Patients with Anterior Disc Displacement of Temporomandibular Disorders].