Design and development on new-type pneumatic test rig

WANG Qing-jiu

DOI: https://doi.org/10.3969/j.issn.1008-0813.2006.02.013

2006-01-01

Abstract:A new-type pneumatic test rig was designed for teaching. This pneumatic test rig can be controlled by pneumatic control, relay control or PLC control. The working principle and characteristics of the pneumatic test rig by applying the three kinds of control methods were introduced respectively.

What problem does this paper attempt to address?

The control principle and realization of the pneumatic mechanical manipulator

Xuan-yin WANG

DOI: https://doi.org/10.3969/j.issn.1002-2333.2001.02.014

2001-01-01

Abstract:Researches on a new type principle and its realization method of multi-degree-freedom pneumatic mechanical manipulator, designs the hardware and software of the computer control, and gives the experimental results.
Design and implementation of multi-functional E-pneumatic learning experimental platform

Tao Guo-liang

2009-01-01

Abstract:Multi-functional pneumatic e-learning experimental platform is based on PLC control unit for the pneumatic system of electronic experiments.Aiming at the original all-pneumatic system for complex hardware structure and signal transmission,the sequential control of thought was introduced.The order controller as the core of the control system,combined with electronic technology and computer technology,the multi-functional electronic pneumatic teaching experimental platform was constituted.The results indicate that the experimental platform simplifies the complex structure of the pneumatic system and is easy to maintain.At the same time,students can facilitate do a wide range of experimental operation,shorten the experiment time,and remove the workload of manual records,etc..
Design of High Pressure Reduction with Expander Pneumatic System' s Controller

陈奕泽,刘荣,贾光政,王宣银

DOI: https://doi.org/10.3969/j.issn.1001-3881.2004.10.073

2004-01-01

Abstract:The controller of high pressure reduction with expander pneumatic system was researched.A high-pressure pneumatic system experimental table was set up.MSP430 ultra-low power consumption chip was adopted as the MCU of the controller inorder to adapt to the limited power supply and working space on the compressed air powered vehicles(CAPV).The experimental Research was done about the predictive PID control of high pressure reduction with expander pneumatic system. Experimental results indicate that can supply stable output pressure,and pressure variation of air supply has little effect to the stable of output pressure.Application tests on the CAPV indicate that pressure reduction with expander system satisfies the requirements of the CAPV in function.
Design of Testing System of Electromagnetic Valve in Pneumatic ABS for Passenger Vehicles

谢建蔚,陶国良,周洪

DOI: https://doi.org/10.3969/j.issn.1001-3881.2004.10.098

2004-01-01

Abstract:Based on the introducing to the operating principle of ABS valves, a testing system,including the test-bed and software for response characteristics was designed.and some methods were applied to improve the testing precision.Test results show that the system is valid and feasible.
Design and Development of Test and Control System for Hydraulic Steering Control Unit Based on Virtual Instrument

Lu Qianqian,Wei Jianhua,Ruan Jian

DOI: https://doi.org/10.4028/www.scientific.net/amm.490-491.1092

2014-01-01

Applied Mechanics and Materials

Abstract:A system combined the function of Industrial Computer, PLC, virtual instruments, sensors and data acquisition was designed and developed for testing and controlling of hydraulic steering control unit, which can achieve automated data acquisition, data processing, test results judgment, false alarms and etc. with the development of computer and science. The software of test system was designed through LabVIEW, and by using module design method, error detection, modify and maintenance of the software turn to be simple and the software become more robust. The system also adopted shielding and filtering with combination of hardware and software to improve test accuracy which reduces test error caused by operators and improve test efficiency.
The generalized pulse code modulation pneumatic servo system and its control

Xuanyin Wang,Guoliang Tao,Fang Ding

DOI: https://doi.org/10.1115/imece1998-0492

1998-01-01

Abstract:Being aimed at the asymmetric pneumatic cylinder, a new type of pneumatic drive circuit is designed. The generalized pulse code modulation (GPCM) pneumatic control system is used for improving performances of the system. In addition, in stead of establishing a nonlinear mathematical model of pneumatic GPCM servo system, system identification by the recursive least square method is applied to find its mathematical model, then a self-tuning controller with the pole-placement approach is designed. In the end, experiments are run in detail. The results show that the GPCM pneumatic servo system is better than the PCM, the self-tuning controller is better than the conventional PID and they are effective in achieving a desired positioning and following accuracy.
The Development of the Static and Dynamic Performance Integrated Test System for Electro-hydraulic Servo Valve

WANG Xuanyin,SUN He,LI Xiaoxiao,LI Fushang

DOI: https://doi.org/10.3969/j.issn.1001-3881.2010.20.013

2010-01-01

Abstract:A static and dynamic performance integrated test system was designed based on virtual instrument technology to meet the needs of performance testing for electro-hydraulic servo valves used in power plant.The control principles and hydraulic circuit of the system were described.The compositions of hardware and software were introduced as well as the performance parameters.Com-paring the result of delivery test with the measured results,it proves that the system is available.The system has been used in practice.
Research and Application of Intelligent Control Method of Small Type Loader Actuator

Youping Gong,Ke Jiang,Tao Jin,Huipeng Chen,Dan Li

DOI: https://doi.org/10.2991/icmmcce-17.2017.230

2017-01-01

Abstract:This paper studies the control system of self-excavated excavator, which is based on the working device of the small type loader. Firstly, the kinematics model of the working device is established by D-H method, so that the trajectory planning of the vehicle speed, boom oil cylinder and bucket oil cylinder drive equation is obtained. Combined with the advantages of PID control and fuzzy control, the fuzzy adaptive PID controller of the actuator is designed. Finally, the simulation model of the hydraulic system position controller is built in Simulink. The simulation results show that the displacement error of the actuator is within 0.5mm.
Extra-high Pressure Pneumatic Test Bed Based on Virtual Instruments

XU Zhipeng,WANG Xuanyin,YU Zhuang

DOI: https://doi.org/10.3969/j.issn.1001-3881.2006.08.029

2006-01-01

Abstract:The standard of extra-high pressure pneumatic technology and actual operating condition was considered,the testing program based on LabVIEW was developed,and systematic test was tried.The test bed consists of high-pressure air supply,control system,artificial load,detection and data acquisition system.Successful design of the test bed contributes a lot to the research of extra-high pressure pneumatic pressure reducing technology.
Automatic Testing and Control System for Electro-Hydraulic Proportional Displacement Pump Based on LabVIEW

陆倩倩,魏建华,赖振宇

DOI: https://doi.org/10.3969/j.issn.1004-1699.2009.04.005

2009-01-01

Abstract:An automatic testing and control system for electo-hydraulic proportional displacement pump with computer aided test is designed and developed, including sensor technology, programmable logic controller, industry PC and virtual instrument. The precision of all parameters is assured by speed, pressure and flow closed loop. By using virtual instrument technology, the testing of the over-all properties including static and dynamic characteristics of the electo-hydraulic proportional displacement pump is realized, mainly comprising fundamental performance test, pressure and flow control hysteresis test as well as pressure and flow response test. It turns out to be a higher accurate and efficient test system in practice. During the test, an abnormal output can be detected immediately, at the same time self protection is carried out.
Research On Pneumatic-Servo Calligraphy Robot

Gl Tao,Xy Wang

2001-01-01

Abstract:With the emergence of the pneumatic-servo system, pneumatic system control is extended from logical control to servo control area, Due to the substantial nonlinearities of pneumatic-servo system which is mainly caused by air compressibility, valve deadzone and saturation, and cylinder friction, it has been used mainly for relatively simple tasks. Many researchers were engaged in pneumatic-servo system because of its simple in structure, high performance to cost, and easy to operate, but rather limited in "point-to-point" positioning control. This paper is focused on the continuous position tracking control of pneumatic-servo system. By analysis of inner pressure control system, outer motion control system, static and kinetic friction of cylinder, a friction observer of cylinder is designed. It is shown that the nonlinear mechanical friction causes a stick-slip response in system. At last, a 3-R pneumatic-servo calligraphy robot, which can write Chinese calligraphy, is developed. Three dimensional position, data are recorded to the computer by RS-232 port between Unis-pen device and computer. Computer deals with the recorded data and communicates with controller by another RS232 port at real time. The experiment demonstrates that the pneumatic-servo system has excellent tracking characteristics and can rival the expensive electro-servo system in many area of industry.
Design and Simulation of Pneumatic Proportional Extra-High Pressure Valve

WANG Xuan-yin,CHEN Yi-ze,LIU Rong,LIANG Dong-tai

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.05.003

2005-01-01

Abstract:A new type pneumatic proportional extra-high pressure valve was developed. In this valve, pilot air is led out from the main valve's inlet, passes through pressure regulating chamber, then drains into the main valve's exhaust chamber. A proportional electro-magnet was used as pilot control component, and the control strategy used electric closed-loop feedback. The useful output pressure range is 8—25 MPa. A nonlinear mathematical model of the valve was established for analyzing the effects of the structural parameters and controller parameters on the valve's dynamic characteristics. The valve worked well under the designed pressure. Fixed parameters of the PI controller cannot meet the needs of control for both high output pressure and low output pressure. The regulating chamber volume has the most important influence on the valve's dynamic characteristics, and increasing the regulating chamber volume is the most effective solution to reduce the vibration amplitude of output pressure and improve the output pressure accuracy.
Research and Development of A Test System for the Dynamic Performance Testing of Pneumatic Solenoid Valves

H. Liu,G. L. Tao,Z. Xiang

DOI: https://doi.org/10.4028/www.scientific.net/amm.278-280.897

2013-01-01

Applied Mechanics and Materials

Abstract:Based on the study of a new method which can calculate the dynamic performance parameters with the dynamic pressure data of the valve in the high-speed on/off process, a test system for the dynamic performance testing of pneumatic solenoid valves is developed in this paper. The dynamic performance of a pneumatic solenoid valve that obtained by test is a key index data for selection and application. To study the dynamic process, a mathematic model of the dynamic pressure in the valve's control cavity is built up. As analyzing the relationship between the movement of the valve spool and the dynamic pressure during its high-speed on/off process, the method proposed a new criterion that can pick out the key points of the spool's movement by the data of dynamic pressure which can be obtained by test easily. Then, the dynamic performance parameters of the valve can be determined with those key points. The structure of the test system that formed on this method is presented. Comparing the test results obtained from the new test system build in this paper with the results obtained from the valve spool displacement laser detection system, it is showed that every characteristic parameter is matched well. The comparing error of total opening time delay and total closing time delay are less than 3%. It is verified that the new method can test the dynamic performance of pneumatic high-speed on/off valve accurately.
Application of PLC in safety performance test of compressor

Hong-min WANG,Xing-ning ZHANG,Ze-kui ZHOU

DOI: https://doi.org/10.3969/j.issn.1673-193X.2008.06.025

2008-01-01

Abstract:This paper presented a self-design test system of auto air-condition compressor.The system,based on SIEMENS SIMATIC S7-300 PLC,could complete all testing items automatically.Its basic characteristics,equipments,control flow and PLC hardware and software design were introduced.Practice proved that this system can improve the testing rate remarkably.
Research and Application of the Driller Control System on Ground Blowout Preventer Control Device

WANG Tao,DING Hui,LIU Jun,LI Hao,TENG Pai

DOI: https://doi.org/10.3969/j.issn.1003-7241.2012.03.013

2012-01-01

Abstract:The renovation of the driller control system on electrical-gas-control ground blowout preventer control device takes SIEMENS S7-300 PLC and Profibus technology.It makes blowout preventer control time shortens greatly,enhances the system safety,reliability.Through the electic button for blowout preventer control,through the addition of sound,light alarm system,controls the status indicator,pressure display digital tube,improves the operating personnel maneuverability,makes the whole control system more humane.
The Hydraulic System Design of High Pressure Servo-control Pulse Test Bed

WANG shuang,DENG Qian-kun,ZHANG Bin

2012-01-01

Abstract:Pressure pulse of hydraulic system has great influence on the life of hydraulic components.In this paper,a pressure pulse test stand is designed to simulate the trapezium pressure pulse in aircraft hydraulic cylinder when at work.A servo valve is used directly to control the pressure to ensure the accuracy of test curve.The simulation model is built by using AMESim to verify the reliable of designed hydraulic system.The effects of important parameters were discussed which can provide guidance to the pressure pulse test bed.It shows that the rise rate of the pressure pulse curve has close related to the instantaneous flow capacity of the servo valve.
Pneumatic High-Pressure Mud Pump Based on PLC Control

Yi Hong Xu,Chang Sheng Zhu

DOI: https://doi.org/10.4028/www.scientific.net/amm.716-717.1595

2014-01-01

Applied Mechanics and Materials

Abstract:This paper proposes a design of pneumatic high-pressure mud pump based on PLC control. According to this method, we design the three-cylinder reciprocating single acting pneumatic high-pressure mud pump, and give the details of PLC control system and high-pressure pump body, finally briefly describe the working principle and the experimental results.
Design and Implementation of Testing Device for Damping Oil Bulk Modulus and Fatigue Characteristic

JIANG Qiang,ZHANG Dawei

DOI: https://doi.org/10.3969/j.issn.1003-1251.2012.02.005

2012-01-01

Abstract:Hydraulic oil bulk modulus and fatigue property parameters are very important physical parameters in the hydraulic system,directly affects the stability and dynamic quality of the system.Based on the definition of the elastic modulus,the testing device for damping oil bulk modulus and fatigue characteristic has been designed,while using the oil gas suspension device of special purpose vehicle asthe testing object,where the fatigue characteristic parameters of hydraulic damping oil have been tested,such as temperature,viscosity.And the design of control system and data acquisition system are completed,timely communication with the host computer,the automatization of the test process is realized.
Control system design of detection device for pipe air tightness based on water test method

Wei Wei

DOI: https://doi.org/10.4028/www.scientific.net/AMM.401-403.1195

2013-01-01

Applied Mechanics and Materials

Abstract:Traditional water test method has the advantage of locating leaks can be found, the disadvantage is inefficient manual detection, labor-intensive, can not be automated testing. By analyzing pneumatic and PLC control were introduced, pneumatic system of the detection device was designed, combined with operation process of the pneumatic circuit PLC control system was designed. Through the PLC control solenoid valve opening and closing, thereby control the implementing agencies of the pneumatic circuit, the device complete each course of action to achieve the test. Application of the system has maintained the advantages of the water detection assay, achieved a semi-automated detection, increased the detection efficiency, reduced labor intensity, and easy to operate.
Automatic Control System of Piston Thermal Shock Test Bench Based on Embedded PC

刘震涛,齐放,沈瑜铭,俞小莉,徐小敏

DOI: https://doi.org/10.3969/j.issn.1000-0925.2005.01.011

2003-01-01

Abstract:Under the sudden operation condition such as starting-up at over-low temperature etc, the heat load of an engine piston changes acutely. In order to study the variety of piston temperature and piston thermal stress, an experimental system based on embedded PC+PC has been developed. The design of the hardware and software of the test-bed control system are introduced. And the results compared the test data of embedded PC with that of PLC show that the control system based on embedded PC is better than control system based on PLC.

Design and development on new-type pneumatic test rig

The control principle and realization of the pneumatic mechanical manipulator

Design and implementation of multi-functional E-pneumatic learning experimental platform

Design of High Pressure Reduction with Expander Pneumatic System' s Controller

Design of Testing System of Electromagnetic Valve in Pneumatic ABS for Passenger Vehicles

Design and Development of Test and Control System for Hydraulic Steering Control Unit Based on Virtual Instrument

The generalized pulse code modulation pneumatic servo system and its control

The Development of the Static and Dynamic Performance Integrated Test System for Electro-hydraulic Servo Valve

Research and Application of Intelligent Control Method of Small Type Loader Actuator

Extra-high Pressure Pneumatic Test Bed Based on Virtual Instruments

Automatic Testing and Control System for Electro-Hydraulic Proportional Displacement Pump Based on LabVIEW

Research On Pneumatic-Servo Calligraphy Robot

Design and Simulation of Pneumatic Proportional Extra-High Pressure Valve

Research and Development of A Test System for the Dynamic Performance Testing of Pneumatic Solenoid Valves

Application of PLC in safety performance test of compressor

Research and Application of the Driller Control System on Ground Blowout Preventer Control Device

The Hydraulic System Design of High Pressure Servo-control Pulse Test Bed

Pneumatic High-Pressure Mud Pump Based on PLC Control

Design and Implementation of Testing Device for Damping Oil Bulk Modulus and Fatigue Characteristic

Control system design of detection device for pipe air tightness based on water test method

Automatic Control System of Piston Thermal Shock Test Bench Based on Embedded PC