Abstract:This study followed the approach of dispersing and localizing carbon nanotubes (CNTs) in nanostructured domains of block copolymers (BCPs) by shortening the CNTs via ball milling. The aim was to selectively tune the electrical and mechanical properties of the resulting nanocomposites, e.g., for use as sensor materials. Multiwalled carbon nanotubes (MWCNTs) were ground into different size fractions. The MWCNT length distribution was evaluated via transmission electron microscopy and dynamic light scattering. The nanostructure of the BCPs and the glass transition temperatures of the PB-rich and PS phases were not strongly affected by the addition of CNTs up to 2 wt%. However, AFM and TEM investigations indicated a partial localization of the shortened CNTs in the soft PB-rich phase or at the interface of the PB-rich and PS phase, respectively. The stress-strain behavior of the solution-mixed composites differed little from the mechanical property profile of the neat BCP and was largely independent of CNT amount and CNT size fraction. Significant changes could only be observed for Young's modulus and strain at break and may be attributed to CNT localization and small changes in morphology. For nanocomposites with unmilled CNTs, the electrical percolation threshold was less than 0.1 wt%. As the CNTs were shortened, the resistivity increased and the percolation threshold shifted to higher CNT contents. Composites with CNTs ground for 7.5 h and 13.5 h showed no bulk conductivity but significantly decreased surface resistivity on the bottom side of the films, which could be attributed to a sedimentation process of the grind and thereby highly compressed CNT agglomerates during evaporation.

Dispersing Carbon Nanotubes in Aqueous Solutions by a Starlike Block Copolymer

Surfactant Assisted Dispersion of Single-Walled Carbon Nanotubes in Polyvinylpyrrolidone Solutions

Dispersant Selection for Nanomaterials: Insight into Dispersing Functionalized Carbon Nanotubes by Small Polar Aromatic Organic Molecules

Novel Star-Like Surfactant As Dispersant for Multi-Walled Carbon Nanotubes in Aqueous Suspensions at High Concentration

Dispersion behavior of single-walled carbon nanotubes by grafting of amphiphilic block copolymer

Synthesis, Aggregation and Adsorption Behaviour of a Thermoresponsive Pentablock Copolymer

Enhanced Dispersion of Nanotubes in Organic Solvents by Donor-Acceptor Interaction Between Functionalized Poly(Phenylacetylene) Chains and Carbon Nanotube Walls

Polysiloxane Surfactants For The Dispersion Of Carbon Nanotubes In Nonpolar Organic Solvents

Utilizing Fullerenols as Surfactant for Carbon Nanotubes Dispersions Preparation

A Novel Ferrocene-Containing Polymer Based Dispersant for Noncovalent Dispersion of Multi-Walled Carbon Nanotubes in Chloroform

Effect of Processing Conditions on the Dispersion of Carbon Nanotubes in Polyacrylonitrile Solutions

A novel biomimetic polymer as amphiphilic surfactant for soluble and biocompatible carbon nanotubes (CNTs)

Effect of cutting and functionalization of single-walled carbon nanotubes on their dispersion behaviors

Polymeric surfactants with tricyclic rigidity from natural rosin: Synthesis and dispersion of single-walled carbon nanotubes in aqueous solution

Influence of CNT Length on Dispersion, Localization, and Electrical Percolation in a Styrene-Butadiene-Based Star Block Copolymer

Tailorable Aqueous Dispersion of Single-Walled Carbon Nanotubes Using Tetrachloroperylene-Based Bolaamphiphiles Via Noncovalent Modification.

Polymer Structure and Solvent Effects on the Selective Dispersion of Single-Walled Carbon Nanotubes

Individually Dispersing Single-Walled Carbon Nanotubes with Novel Neutral Ph Water-Soluble Chitosan Derivatives

Simulation of Dispersion and Alignment of Carbon Nanotubes in Polymer Flow Using Dissipative Particle Dynamics

Polysiloxane surfactants for the dispersion of carbon nanotubes in non-polar organic solvents

Dendrimer Assisted Dispersion of Carbon Nanotubes: A Molecular Dynamics Study