Abstract:To investigate the hot deformation characteristics, workability, and interfacial microstructure of the titanium/steel bimetallic composite, hot compression simulations were carried out on the TA1/SUS430 composite within the temperatures of 750 °C–1050 °C, accompanied by strain rates spanning from 0.01 s⁻1–10 s⁻1. The hyperbolic sine Arrhenius constitutive equation and back-propagation artificial neural network (BP-ANN) model for flow stresses of this bimetallic composite were developed. 2D and 3D hot processing maps were established to study processability. The results revealed the calculated average activation energy (Q) was 277.9671 kJ/mol. The BP-ANN model demonstrated higher prediction accuracy than the Arrhenius model, with a correlation coefficient (R 2) of 0.99947. As the strain increases, the area of the unstable region in the processing map expands, and the failure mode is characterized by the formation of microcracks at the bonded interface. Interfacial exfoliation manifested under elevated temperature and high strain rate deformation conditions. High power dissipation (η) values were observed within the processing parameters of 875°C–950 °C/0.01 s−1-0.03 s−1. The bimetal exhibited superior deformation coordination at low strain rates. TiC predominantly constituted the interface products at lower temperatures, while at higher temperatures, phases containing both Fe and Ti dominated. Furthermore, the deformed steel stratum manifested a pronounced cubic orientation <001>//CD and a less dominant recrystallized γ orientation. This γ texture attenuated progressively with increased deformation temperatures, while the strain rate has less impact.

Flow Stress Behavior of In-situ TiB2/Al-Si-Mg-Cu Composite at High Temperature

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Flow Behavior and Microstructure Evolution of TB8 Alloy During Hot Deformation Process

High Strain Rate Response of In-Situ TiB2/7055 Composite by Taylor Impact

Compressive response and microstructural evolution of in-situ TiB2 particle-reinforced 7075 aluminum matrix composite

Flow Behavior and Constitutive Equation of Ti-6.5Al-2Sn-4Zr-4Mo-1W-0.2Si Titanium Alloy

Hot deformation behavior of in-situ nanosized TiB2 particulate reinforced AZ91 Mg matrix composite

Thermo⁻Mechanical Behavior and Constitutive Modeling of In Situ TiB2/7050 Al Metal Matrix Composites Over Wide Temperature and Strain Rate Ranges

Hot Deformation Behavior and Microstructural Evolution of a TiB2/Al-Zn-Mg-Cu-Zr Composite

High fatigue performance and microscopic mechanisms of in-situ TiB 2 /7050Al composite at different temperatures

Hot Deformation Behavior and Workability of In-Situ TiB2/7050Al Composites Fabricated by Powder Metallurgy

High temperature flow behavior and constitutive model of alloy transition layer in composite steel tube prepared by centrifugal self‐propagating high‐temperature synthesis (SHS)

Flow characteristics, ANN-based prediction, 3D processing map, and interface microstructure of titanium/stainless steel bimetallic composite

Strain Compensation of the Constitutive Equation for High Temperature Flow Stress of a Al-Cu-Li Alloy

Hot Deformation Behavior of the 20 Vol.% TiC/Cu-Al2O3 Composites

The flow behavior of homogenizated Al-Mg-Si-La aluminum alloy during hot deformation

Flow softening and microstructural evolution of near β titanium alloy Ti-35421 during hot compression deformation in the α+β region

Hot deformation behavior and microstructural evolution of particulate reinforced AA6061/B4C composite during compression at elevated temperature

The High-Temperature Deformation Behavior of As-Cast Ti90 Titanium Alloy

Electron Backscatter Diffraction Investigation on Microstructure Evolution of TiB2(p)/Al-Cu Composite after Single-Pass Equal Channel Angular Pressing for Formability Assessment

Effect of Initial Microstructure on the Temperature Dependence of the Flow Stress and Deformation Microstructure under Uniaxial Compression of Ti-407