Kinetics Study about In-situ Mining and Dump Leaching Certain Low Quality Copper

LI Hui-juan,WU Heng-shan,LI Chao

DOI: https://doi.org/10.3969/j.issn.1004-5716.2007.02.038

2007-01-01

Abstract:This paper analyses the result of in-situ mining and dump leaching briefly,using kinetics method of certain low quality copper ore in Hunan province,get the reaction speed of this ore,and it offers the gist for leaching this ore.

What problem does this paper attempt to address?

Kinetic Investigation on Leaching of Copper from a Low-Grade Copper Oxide Deposit in Sulfuric Acid Solution: A Case Study of the Crushing Circuit Reject of a Copper Heap Leaching Plant

Mostafa Hosseinzadeh,Ali Entezari Zarandi,Louis-César Pasquier,Asghar Azizi

DOI: https://doi.org/10.1007/s40831-021-00408-5

2021-07-28

Journal of Sustainable Metallurgy

Abstract:In this study, the reject fraction of the jaw crusher, located in the first part of the crushing circuit, is used as a considerable stock in copper tank-leaching plant. High market value of copper and ease of practice were the motivating forces on studying the leaching kinetics under controlled conditions. In this regard, first, the influencing parameters such as the acid concentration, solid-to-liquid ratio, agitation speed, particle size, and temperature were assessed on the leaching fraction of copper. The findings showed that the leaching rate is nearly independent of the agitation rate at the high values of 300 rpm. The recovery of copper strongly promoted from 2 to 90% by increasing sulfuric acid concentration from 0.3 to 1.8 M. The increase in the solid-to-liquid ratio and temperature were found to be beneficial as well. Additionally, it was found that above 71% copper could be leached from the reject samples in the size range of 0–2 mm by 0.9 M sulfuric acid after 30 min contact time at 25 °C temperature. In the second stage, the leaching kinetics was studied by shrinking core models to gain a better description of the dissolution process of copper from crushing circuit reject. The results indicated that the dissolution rate could be controlled by both chemical reaction and diffusion process. However, diffusion process was the dominant mechanism in the system investigated. Ultimately, a mixed kinetic model with an activation energy of 11.72 kJ/mol was proposed as the leaching rate-controlling step.Graphical Abstract

metallurgy & metallurgical engineering,green & sustainable science & technology
Leaching Kinetics of Cu from Low-Grade Oxidized Copper Ore with High Alkalinity Gangue Using Edta·2na Solution

Faxin Xiao,Zhihua Luo,Yu Peng,Xuwei Luo,Yaoyu Yan,Shuchen Sun,Ganfeng Tu

DOI: https://doi.org/10.1007/s11837-024-06649-5

2024-06-05

JOM

Abstract:Low-grade oxidized copper ore with a high alkaline gangue content is considered refractory due to its high CaO and MgO content, which leads to significant sulfuric acid consumption during leaching and environmental pollution from the ammonia leaching process. In this study, an aqueous solution of ethylenediaminetetraacetic acid disodium salt (EDTA·2Na) was utilized as a leaching agent to explore the influence of key process variables, such as leaching temperature, EDTA·2Na concentration, leaching duration, stirring rate, and liquid-to-solid volume mass ratio, on the copper leaching rate over various durations. The kinetic analysis shows that the Cu leaching process of this ore with EDTA·2Na solution is mixed, controlled by both interfacial chemical reaction and solid product layer diffusion. The apparent activation energy EA = 11.32 kJ/mol, and the apparent reaction order, α, for EDTA·2Na concentration is 1.151, the apparent reaction order, β, for stirring rate is 0.245, and the apparent reaction order, θ, for the liquid–solid ratio is 0.021. The kinetic equation is .

materials science, multidisciplinary,metallurgy & metallurgical engineering,mineralogy,mining & mineral processing
Optimizing Conditions for Bacterial Leaching of Copper from Discarded Mines

MQ Qiu,GX Wang,WM Zhang,SY Xiong

DOI: https://doi.org/10.1016/s1005-8850(06)60024-8

2006-01-01

Abstract:The effect of process parameters (pH, pulp density, inoculum volume, ferrous content, particle size) on the rate of copper solubilization was analyzed respectively through bioleaching tests with mixed bacteria in shake flasks. These results show that the optimal process parameters are: pH, 1.50–1.80; pulp density, 5wt%; inoculum volume, 10vol%; ferrous content, 2g-L−1; particle size, <0.076 mm. Furthermore, when the pH value is below 1.50 in leaching solution, the iron precipitated can be reduced to a great extent, but it shows low bacterial activity at this pH. Finally, it is emphasized that the optimal parameters are also determined by economical benefit.
Bacterial Leaching of Discarded Copper Ores from Yongping, China

MQ Qiu,GX Wang,ZS Shen

2005-01-01

Abstract:The elementary and phase analysis of discarded copper ores from Yongping of China has been performed. The experiments of extracting copper from the discarded copper ores were done with the mixed bacteria obtained through a series of enrichment, separation, domestication and combination tests. The results show that in the process of bioleaching, the pH value rises at first and drops gradually. The E-h value keeps rising along with the time and the appropriate E-h value varying between 750 and 800 mV will benefit the bioleaching copper. The high concentration of ferric ions is detrimental to the bioleaching copper. The results of bioleaching copper are good. That is, the copper recovery is 31.8% after 27 days.
Leaching Experiments on Cadmium Release from Cd-rich Oxidized Rocks at Jinding Pb-Zn Deposit

LI Hang,SHUANG Yan,ZHU Changsheng,LI Dahua,TAN Xianlong,LI Zhengnan

DOI: https://doi.org/10.3969/j.issn.1674-5906.2007.04.011

2007-01-01

Abstract:The Jinding Pb-Zn deposit in Yunnan is a typical high Cd-rich area in China. A long time leaching experiments about two Cd-rich oxidied ore were conducted at ambient temperature through simulating rainfall. The results show pH values (pH=7.2～8.5) and SO42-concentrations of leachate tread to stabilization with increasing leaching time.The Cl -concentration of leachate increases markedly. The soluble Cd,Pb,Zn,Cu and Mn concentration distribution vary with adverse decreasing. The release of cadmium in both oxidized ore exixits remarkable difference,and is probably affected by the main factor of smithsonite component content in ore. The leaching test shows that Pb/Zn ore are susceptibly to be oxidized or dissolved and readily release Cd and other harmful element. These leached elements in the leachate may deposit rapidly,and the depositing rank presents ZnPbCd. The natural weathering of Cd-rich rock and mineral presents potential environment risk for the aquatic ecosystem of Jinding catchment.
Modelling Particle Scale Leach Kinetics Based on X-ray Computed Micro-Tomography Images

Q. Lin,D. J. Barker,K. J. Dobson,P. D. Lee,S. J. Neethling

DOI: https://doi.org/10.1016/j.hydromet.2016.02.008

IF: 4.217

2016-01-01

Hydrometallurgy

Abstract:The apparent leach kinetics for an ore particle within a heap leaching system depend on the chemical conditions in the fluids around the particle, the mass transport within the particle and the reaction kinetics at the surface of each mineral grain. The apparent rate kinetics thus depend upon the distribution of the mineral grains, in terms of both size and position, within the individual ore particles, as well as the evolution of this distribution. Traditionally this behaviour has been modelled using simplified relationships such as the shrinking core model. In this paper a method for simulating this evolution and the resultant kinetics based directly on 3D XMT images of the internal structure of the particles is presented. The model includes mass transport through the gangue matrix, surface reaction kinetics and the dissolution and subsequent evolution of the individual mineral grains within the ore particle. Different minerals and mineral associations will result in different surface reaction kinetics. One of the key inputs into this model is thus the distribution of the surface rate kinetics. A method for experimentally determining this distribution is presented. The simulation results are compared to the evolution of real particles as they undergo leaching as measured using a time sequence of 3D XMT images of a leaching column. It was found that these simulations are able to accurately predict both the overall leaching trends, as well as the leaching behaviour of mineral grains in classes based on their size and distance to the particle surface. The leaching behaviour did not follow that of a simple shrinking core approximation, with the actual spatial and size distribution of the grains, as well as the distribution of their surface rate kinetics, all impacting the apparent leach kinetics. For the copper ore particles used in this work the best fit to the experiments was achieved at an intermediate value of the dimensionless group that characterises the relative importance of surface kinetics to diffusion indicating that both need to be considered for accurate modelling. This paper thus demonstrates that using 3D XMT to provide both structural and kinetic data and incorporating this information into a particle scale simulator provides an improved basis for predicting particle scale leach performance.
Study on leaching kinetics of bauxite residue

Wu Yi-feng,LIU Zhi-rong,ZENG Kai,LI Ying

DOI: https://doi.org/10.16283/j.cnki.hgkwyjg.2008.05.003

2008-01-01

Abstract:Kinetic study of the leaching of powered bauxite residue in sulfuric acid solution has been investigated.Leaching reaction is affected by reaction temperatute and applicable to the chemical reaction according to shrinking core model.The reaction kinetics is shown as :1-(1-x)13=kt,k=216 exp[-33900RT].
Leaching Thermodynamics of Low-Grade Copper Oxide Ore from [(NH4)2SO4]-NH3-H2O Solution

Faxin Xiao,Xinyu Cao,Xuwei Luo,Ganfeng Tu,Cuixia Yang,Yu Peng,Hui Li,Wei Xu,Shuo Wang

DOI: https://doi.org/10.3390/ma17194821

IF: 3.4

2024-10-01

Materials

Abstract:This paper describes a highly alkaline low-grade copper oxide ore. Copper can be selectively leached out while other metals are retained. A thermodynamic model of the CuO-(NH4)2SO4-NH3-H2O system was established for the leaching of tenorite (CuO) under conditions of mass and charge conservation. MATLAB's fitting functions, along with the diff and solve functions, were used to calculate the optimal ammonia concentration and total copper ion concentration of tenorite under different ammonium sulfate concentrations. The effects of various ammonia–ammonium salt solutions (ammonium sulfate, ammonium carbonate, ammonium chloride) on the copper leaching rate were investigated. Results show that under the conditions of an ammonia concentration of 1.2 mol/L, an ammonia–ammonium ratio of 2:1, a liquid–solid ratio of 3:1, a temperature of 25 °C, and a leaching time of 4 h, the copper leaching rate from the ammonium sulfate and ammonium chloride solutions reaches 70%, which is slightly higher than that of ammonium carbonate. Therefore, an ammonia–ammonium sulfate system is selected for leaching low-grade copper oxide due to its lower corrosion to equipment compared to the chlorination system. The impact of this study on industrial applications includes the potential to find more sustainable and cost-effective methods for resource recovery. The industry can reduce its dependence on resources and mitigate its environmental impact. Readers engaged in low-grade oxidized copper research will benefit from this study.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
RESEARCH ON UNDERGROUND SOLUTION LEACHING OF SULFIDE COPPER ORE COMBINED WITH BIOOXIDATION

何良菊,王春,蒋开喜

DOI: https://doi.org/10.3969/j.issn.1005-7854.2002.02.010

2002-01-01

Abstract:The mechanism of sulfide copper ore bio-oxidation and the characteristics of underground solution leaching were discussed. Three kinds of copper sulfide ore sample were used to conduct a comparison test on weak sulfuric acid leaching and sulfuric acid-ferric leaching(ferric in the form of chemical compound and produced by oxidation using T ferrooxidans),The test results show that the extraction of copper was increased by 756%,21.62%,10.59% according to reserves of copper sulfide ore is 15.02%,45.60%,79.35% respectively with addition of ferric 2.0～3.0g/L.Extraction of iron was 10.68%,8.9%,7.12% with addition of ferric 0.0,1.0,3.0g/L respectively.Base on the experiment,leaching process enhanced by biooxidation has been developed and become easy to be performed in engineering practice for recovering the copper from sulfide ore.
Study on Bioleaching Conditions of Low-grade Primary Copper Sulfide Ore from Yongping Copper Mine

Zhang Weimin,Gu Shifei,Yu Rong

DOI: https://doi.org/10.3321/j.issn:1001-1250.2006.02.011

2006-01-01

Abstract:To recover and utilize the low-grade primary copper sulfide ore resource in the waste ore in Yongping Copper Mine,the effect of inoculation concentration,initial Fe~(2+) concentration,ore particle size and pulp density on its bioleaching was studied.The results show that the conditions beneficial to the copper leaching include inoculation concentration of 20%,initial Fe~(2+) concentration of 0 g/L,initial pH value of 1.2,controlling the pH value in the leaching process to be under 1.50,ore particle size of 5 mm and pulp density of 20%~25%.Too high a ferric concentration and the iron precipitation in the solution will directly affect the bioleaching effect.Though the leaching bacteria can well adapt to the ore leaching environment,measures for strengthening the leaching should be taken due to the slow leaching speed and rate of copper.
Leaching Behaviors of Yulong Refractory Oxide Copper Ores from Tibet in Sulfuric Acid Solutions

Jian Wang,Yi Liu,Yonghao Lu,Wenlong Xu,Kang Yan,Ruixiang Wang,Yue Pan,Jinhui Li,Zhifeng Xu

DOI: https://doi.org/10.1007/s40831-023-00700-6

2023-01-01

Journal of Sustainable Metallurgy

Abstract:Yulong copper mine is located in the Changdu region in the eastern mountainous area of Tibetan Plateau, where the elevation of mining area is over 4500 m. At present, the oxide ores from Yulong No. II bodies are refractory to direct agitation leaching in sulfuric acid media under normal leaching conditions. In this research, the mineralogical characteristics of this type of copper ores have been examined using automated mineral liberation analysis (MLA) integrated with scanning electron microscopy. The results showed that this type of copper ores had an extremely high binding rate due to the encapsulation of copper-bearing minerals within gangue minerals, such as kaolinite clay. For the agitation leaching process of Yulong copper ores in sulfuric acid media, the effects of leaching parameters were investigated on copper extraction, aluminum and iron dissolution, respectively. The studied parameters include liquid/solid ratio, agitation speed, leaching temperature, initial sulfuric acid concentration and particle size. The results of kinetic analysis of the leaching data under various leaching temperature indicated that the agitation leaching of copper ores belongs to diffusion control, giving an activation energy of 6.86 kJ/mol for copper extraction, 6.99 kJ/mol for aluminum dissolution and 14.96 kJ/mol for iron dissolution, respectively. Copper recovery from agitation leaching after ball milling as high as 85
Study on leaching kinetics of laterite ore using hydrochloric acid

Jinhui Li,Zhifeng Xu,Ruixiang Wang,Yang Gao,Yang Yang

DOI: https://doi.org/10.5277/ppmp18189

2019-01-01

Physicochemical Problems of Mineral Processing

Abstract:The process of atmosphere-pressure acid leaching of laterites has attracted considerable attention in the nickel industry in recent years. However, the leaching kinetics of laterite using hydrochloride acid has not yet been fully researched. In this paper, the mineral analysis of the ore was carried out, and the leaching mechanism of different minerals at different time was studied comprehensively. The kinetics analysis of the leaching process of nickel, cobalt and manganese showed that the kinetics model of diffusion controlling was suitable and could be described by the linear equation, 1-3(1-a)(2/3)+2(1-a)=k(2)t. Based on the linear equation and the Arrhenius equation, the values of activation energy of metal leaching can be deduced (11.56 kJ/mol for nickel, 11.26 kJ/mol for cobalt and 10.77 kJ/mol for manganese). Study of leaching mechanism shows that the order of these minerals dissolution is: goethite, lizardite, magnetite and hematite. Due to the original or product of silica, magnetite, hematite and talc, they can form the solid film which hinders the leaching of valuable metals. Thus, the diffusion controlling step is inner diffusion, namely solid film diffusion controlling.
Mechanism and kinetics study on waste acid leaching from copper smelting dust

Weisong Cai,Xiaohua Yu,Yan Lin,Qingfeng Shen,Yiming Zhu,Hongkun Dai

DOI: https://doi.org/10.1002/ep.14350

IF: 2.824

2024-01-23

Environmental Progress & Sustainable Energy

Abstract:Copper smelters generate large amounts of copper smelting dust (CSD) that has a high recycling value because it contains about 20% copper. Waste acid can be used to leach CSD. Here, the effects of different temperatures, times and liquid–solid ratios on copper, iron and arsenic leaching rates were investigated. The optimal conditions were determined to be a temperature of 95°C, leaching time of 3 h, and liquid–solid ratio of 7:1. Under these condition, the leaching rate of copper reached 96.37%, and the copper ion concentration was 32.71 g/L. The leaching kinetics date revealed that the leaching of copper and iron was controlled by two different reaction models. The leaching of copper conformed to the Johnson–Mehl–Avrami (JMA) model and was diffusion controlled, and the reaction was rapid in the first 60 min. In contrast, leaching of iron was controlled by a chemical reaction. Copper and iron activation energies were 2.579 and 62.791 kJ/mol, respectively. These results show that CSD waste acid is can be used to dispose of arsenic‐containing hazardous waste in a green, sustainable, and ecologically method.

environmental sciences,green & sustainable science & technology,engineering, environmental, chemical
Study on the mineral processing technology of a high Ca-Mg contents and sulphide-oxide mixed copper-cobalt ore in Congo (Kinshasa)

Yongchao PIAO,Hairui YANG,Ligang WANG,Zhiqiang HU,Yuehua YE,Xubo CHEN

2018-01-01

Abstract:An experimental study on a high Ca-Mg contents and sulphide-oxide mixed copper-cobalt ore in Congo (Kinshasa) has been conducted ,and the study compared with technology and economy of three different process methods :leach raw ore directly ,sulphide flotation-oxide flotation (no cleaning )-leaching , sulphide flotation-oxide flotation (cleaning )-leaching .Results show that :copper and cobalt recoveries of second process method is highest ,but the third process method have the best economic benefits .In addition , magnetic separation of flotation tailings can add 7.15 percentage points to total cobalt recovery of beneficiation .
Leaching behaviors of copper and arsenic from high-arsenic copper sulfide concentrates by oxygen-rich sulfuric acid leaching at atmospheric pressure

Weijiao Yang,Long Qian,Bingjie Jin,Qing Feng,Lei Li,Kunyun He,Jinlei Yang

DOI: https://doi.org/10.1016/j.jece.2022.107358

IF: 7.7

2022-04-01

Journal of Environmental Chemical Engineering

Abstract:High arsenic copper sulfide concentrates (HACSC) are becoming increasingly common in the world. Copper pyrometallurgy brings a series of problems, such as arsenic-containing dusts and waste acids that are difficult to treat. Hydrometallurgical process is an attractive alternative to treat HACSC. This work dealt with the leaching behaviors and kinetics of copper and arsenic from HACSC by oxygen-rich acid leaching at atmospheric pressure systematically. The leaching temperature, oxygen flux, liquid-solid ratio, sulfuric acid concentration and time have significant effect on the leaching of copper and arsenic. However, the effects on the copper leaching efficiency were much greater than that on the leaching efficiency of arsenic. The experimental optimization conditions were obtained as follows: temperature 80 °C, liquid-solid ratio 20:1, stirring speed 400 r·min-1, oxygen flux 2 L·min-1, sulfuric acid concentration 270 g·L-1. Under these conditions, > 99% copper was leached within 18 h, > 95% arsenic was leached within 36 h. The X-ray diffraction (XRD) and Scanning Electron Microscope/ Energy Dispersive Spectrometer (SEM/EDS) studies confirmed that the changes in the phases and morphologies before and after the leaching processes corroborated the leaching behavior of copper and arsenic. Furthermore, copper leaching kinetic model followed the shrinking core model of the couplings control of diffusion and surface chemical reaction. The activation energy was 36 kJ/mol. The kinetic equations for the effect of leaching temperature, oxygen flux and sulfuric acid concentration were obtained, respectively. The overall kinetic equation which can be applied in solids with particle families of limited size was also developed.

engineering, chemical, environmental
Chalcocite (bio)hydrometallurgy—current state, mechanism, and future directions: A review

Shichao Yu,Rui Liao,Baojun Yang,Chaojun Fang,Zhentang Wang,Yuling Liu,Baiqiang Wu,Jun Wang,Guanzhou Qiu

DOI: https://doi.org/10.1016/j.cjche.2021.12.014

IF: 3.8

2022-01-01

Chinese Journal of Chemical Engineering

Abstract:There has been a strong interest in technologies suited for mining and processing of low-grade ores because of the rapid depletion of mineral resources in the world. In most cases, the extraction of copper from such raw materials is achieved by applying the leaching procedures. However, its low extraction efficiency and the long extraction period limit its large-scale commercial applications in copper recovery, even though bioleaching has been widely employed commercially for heap and dump bioleaching of secondary copper sulfide ores. Overcoming the technical challenges requires a better understanding of leaching kinetics and on-site microbial activities. Herein, this paper reviews the current status of main commercial biomining operations around the world, identifies factors that affect chalcocite dissolution both in chemical leaching and bioleaching, summarizes the related kinetic research, and concludes with a discussion of two on-site chalcocite heap leaching practices. Further, the challenges and innovations for the future development of chalcocite hydrometallurgy are presented in the end.

engineering, chemical
Characterization and Optimization of Copper-Cobalt Oxide Ores During Acid Leaching

Jingyuan Xu,Shuchen Qin,Chaozhen Zheng,Jun Wang,Biwen Yang,Guanzhou Qiu,Senlin Cui,Hao Ma

DOI: https://doi.org/10.1007/s11837-023-06151-4

2023-09-27

JOM

Abstract:The copper-cobalt ore received from Congo contains around 2.0% copper and 0.356% cobalt, with oxidation rates of 92.09% and 88.57% for Cu and Co, respectively. Malachite and cornetite are the main copper minerals, while heterogenite and carrollite are the main Co-bearing minerals. To optimize the leaching efficiency of Cu and Co for this type of ore, various operating parameters were investigated, including particle size, pulp density, acidity, leaching time, and reductant. The recovery for Cu and Co can reach 88.36% and 74.58% under pulp density of 33%, acidity of 84 kg/t, leaching time of 4 h, and reductant 12 kg/t. In order to improve the metal recovery, an intensified operating condition (fine grinding, high acidity, and reductant) was applied, and the copper and Co recovery reached 93.07% and 89.56%, respectively.

materials science, multidisciplinary,metallurgy & metallurgical engineering,mining & mineral processing,mineralogy
Leaching of iron from copper tailings by sulfuric acid: behavior, kinetics and mechanism

Lei Tao,Langlang Wang,Kanghuai Yang,Xueqian Wang,Lu Chen,Ping Ning

DOI: https://doi.org/10.1039/d0ra08865j

IF: 4.036

2021-01-01

RSC Advances

Abstract:Leaching behavior of copper tailings with sulfuric acid was expounded. Leaching was optimized: 1 M H 2 SO 4 , S/L of 1 : 10, T = 40 °C, 120 min. Fe 2 SiO 4 was preferentially leached than Fe 3 O 4 . Leaching of Fe is controlled by solid-phase diffusion.

chemistry, multidisciplinary
The deleterious role of gangue mineralogy in copper extraction: A case study of poor recovery in leaching low-grade Cu ores

Nicholas D. Owen,Rahul Ram,Luke Vollert,Brigitte Seaman,Barbara Etschmann,Yanlu Xing,Mareike Rosemann,Luis Verdugo,John O'Callaghan,Joël Brugger

DOI: https://doi.org/10.1016/j.apgeochem.2024.105984

IF: 3.4

2024-03-29

Applied Geochemistry

Abstract:In a series of four extended industrial column leach experiments spanning 542 days, aimed at examining Cu-recovery from low-grade sulfide ores, all instances yielded suboptimal Cu recovery rates (<27%). Through a nuanced analysis integrating time-resolved chemical data on leachate with detailed mineralogical investigations, we highlight that the dissolution of aluminosilicate gangue minerals is a pivotal factor constraining Cu recovery. The source materials, extracted from a low-grade segment of a Cu–Au porphyry deposit (∼0.32–0.36 wt% Cu), underwent diverse leaching conditions employing various lixiviants, curing phases, redox conditions, and particle size distributions. Notably, poor Cu recovery is closely tied to gangue mineralogy. The ammonia leach column experienced limited Cu leaching due to an inert gangue shielding chalcopyrite from the lixiviant. In acid columns, swift precipitation of silica-rich phases impeded effective Cu leaching at multiple scales, from large-scale-column to molecular levels. Identifying gangue mineralogy and considering their impact during acid leaching are crucial for formulating effective lixiviant strategies for Cu recovery from low-grade primary sulfide ores. The curing phase, requiring high acid concentrations (∼50 g/L H2SO4), emerges as a critical aspect for promoting effective gangue dissolution while preventing refractory silica-rich phase precipitation.

geochemistry & geophysics
Study on Process Mineralogy of the Combined Copper Oxide Ore in Tibet and Acid Leaching Behavior with Calcium Fluoride

Zujiang Pan,Cuo Jian,Zaihua Peng,Xinzhuang Fu,Rui He,Tong Yue,Wei Sun

DOI: https://doi.org/10.3390/min14040352

IF: 2.5

2024-03-29

Minerals

Abstract:The Yulong copper deposit in Tibet is a typical porphyry copper deposit, with about 30 million tons of copper oxide ore in the surface layer. However, more than 40% of the copper resources are in a combination state, resulting in an extraction efficiency of only 50% for copper via the hydrometallurgical process. In this study, the process mineralogy of the combined copper oxide ore was systematically investigated and a calcium fluoride-enhanced leaching process is proposed to increase the leaching efficiency of the combined copper ore. The process mineralogy of the combined copper oxide ore was analyzed using various testing techniques, including chemical analysis, X-ray diffraction, and a process mineralogy parameter testing system (Mineral Liberation Analysis). The results revealed that limonite accounted for 86.12% of the sample, and 63.51% of the copper resource existed in the form of combined copper oxide in limonite. However, it is difficult for the uniformly distributed combined copper oxide in limonite to sufficiently make contact with sulfuric acid, which is the leaching agent, resulting in low copper leaching efficiency. The enhanced leaching behavior of the combined copper oxide ores was also investigated, thereby determining effective and economical enhanced leaching conditions. Under optimal conditions, at a grinding fineness ratio of −0.074 mm (accounting for 85%), liquid-solid ratio of 4:1, sulfuric acid concentration of 50 g/L, temperature of 30 °C, CaF2 dosage of 1% of the ore mass, and leaching time of 4 h, the copper leaching efficiency increased to 60.57%, which was 7.34% higher than that of atmospheric pressure leaching. Finally, the enhanced leaching slag was analyzed using an electron probe microanalyzer. It indicated that fluorine ions can erode the combined copper oxide ore and facilitate the diffusion of hydrogen ions inside the limonite, thereby achieving a strengthening effect.

geochemistry & geophysics,mineralogy,mining & mineral processing

Kinetics Study about In-situ Mining and Dump Leaching Certain Low Quality Copper

Kinetic Investigation on Leaching of Copper from a Low-Grade Copper Oxide Deposit in Sulfuric Acid Solution: A Case Study of the Crushing Circuit Reject of a Copper Heap Leaching Plant

Leaching Kinetics of Cu from Low-Grade Oxidized Copper Ore with High Alkalinity Gangue Using Edta·2na Solution

Optimizing Conditions for Bacterial Leaching of Copper from Discarded Mines

Bacterial Leaching of Discarded Copper Ores from Yongping, China

Leaching Experiments on Cadmium Release from Cd-rich Oxidized Rocks at Jinding Pb-Zn Deposit

Modelling Particle Scale Leach Kinetics Based on X-ray Computed Micro-Tomography Images

Study on leaching kinetics of bauxite residue

Leaching Thermodynamics of Low-Grade Copper Oxide Ore from [(NH4)2SO4]-NH3-H2O Solution

RESEARCH ON UNDERGROUND SOLUTION LEACHING OF SULFIDE COPPER ORE COMBINED WITH BIOOXIDATION

Study on Bioleaching Conditions of Low-grade Primary Copper Sulfide Ore from Yongping Copper Mine

Leaching Behaviors of Yulong Refractory Oxide Copper Ores from Tibet in Sulfuric Acid Solutions

Study on leaching kinetics of laterite ore using hydrochloric acid

Mechanism and kinetics study on waste acid leaching from copper smelting dust

Study on the mineral processing technology of a high Ca-Mg contents and sulphide-oxide mixed copper-cobalt ore in Congo (Kinshasa)

Leaching behaviors of copper and arsenic from high-arsenic copper sulfide concentrates by oxygen-rich sulfuric acid leaching at atmospheric pressure

Chalcocite (bio)hydrometallurgy—current state, mechanism, and future directions: A review

Characterization and Optimization of Copper-Cobalt Oxide Ores During Acid Leaching

Leaching of iron from copper tailings by sulfuric acid: behavior, kinetics and mechanism

The deleterious role of gangue mineralogy in copper extraction: A case study of poor recovery in leaching low-grade Cu ores

Study on Process Mineralogy of the Combined Copper Oxide Ore in Tibet and Acid Leaching Behavior with Calcium Fluoride