Abstract:Objective To determine whether operator's skills could influence shear bond strength (SBS) of self-etch adhesive to enamel with or without prior acid-etching.Methods Total 90 bovine incisors were prepared to expose the enamel and randomly assigned to three groups according to the operator's experience:no experienced student group (Group A),four-year experienced expert group (Group B) and ten-year experienced expert group (Group C).Each group was further divided in two subgroups.In one of the subgroups,a self-etching adhesive and composite were applied in accordance with the manufacturer's instructions,and in the other subgroup,prior acid-etching with etchant were applied first,then self-etching adhesive and composite were applied.Shear bond strength of these samples was measured and the results were analyzed with one-way ANOVA.Results Without prior acid-etching,there was statistically significant difference between Group A [(16.32 ± 5.99) MPa] and Group B [(21.36 ± 4.07) MPa] (P =0.006),but no statistically significant difference between Group A and Group C [(18.77 ± 3.78) MPa] (P =0.163) was found.As for the prior acid-etching group,there were statistically significant differences between operators with and without previous experience,i.e.A [(21.34 ± 5.62 MPa) and B[(26.18±3.57) MPa](P=0.007),A and C[(25.35±4.51) MPa](P=0.023).Whether the subgroup with prior acid-etching or not,thcrc was no statistically significant difference between expert groups (Group B and Group C).The shear bond strength of experienced expert groups was higher than that in no experienced student group.Furthermore,there was statistically significant difference between subgroups with and without prior acid-etching,i.e.A (P =0.025),B (P =0.002) and C (P =0.000).The shear bond strength with prior acid-etching was higher than those without prior acid-etching.Conclusions Operator's experience in enamel adhesive appears to play an important role in determining the outcome of shear bond strength.In order to achieve optimal adhesive outcomes,it is important for operators to not only be familiar with adhesives' knowledge,but also have some practical experience and should operate strictly according to the manufacturer's instructions.

The study on the influence of bovine enamel hardness measurement methods on the result evaluation]

Effects of Regional Enamel and Prism Orientations on Bovine Enamel Bond Strength and Cohesive Strength

Effect of using bleaching materials on bovine enamel hardness

The Crystal Structure and Mechanical Characteristics of Enamel and Dentin of Primary and Permanent Teeth

Test of Hardness and Wear Resistance of Artificial Carious Human Enamel

Comparative Evaluation of Dental Enamel Microhardness Following Various Methods of Interproximal Reduction: A Vickers Hardness Tester Investigation

Measuring Fracture Toughness of Human Dental Enamel at Small Scale Using Notched Microcantilever Beams

A New Method for Characterization of Thermal Properties of Human Enamel and Dentine: Influence of Microstructure

Effect of the prism-interprisms three-dimension spatial microstructure on the enamel bond strength

[Influence of Different Surface Roughness on the Wear Performance of Several Commonly Used Dental Materials].

Comparison of wear resistance and hardness among different resin teeth

The Mechanical Anisotropy on a Longitudinal Section of Human Enamel Studied by Nanoindentation.

The microstructure properties of human enamel on the multi-scale

Effects of Different Over – the - Counter Whitening Products on the Microhardness, Surface Roughness, Color and Shear Bond Strength of Enamel

Microhardness Measurements on Tooth and Alveolar Bone in Rodent Oral Disease Models

Microstructures and Mechanical Characteristics of Enamel and Dentin of Primary and Permanent Teeth

Novel Method to Measure Enamel Surface Porosity with Hydrogen Peroxide Bleaching

Evaluation of the Bonding Shear Strength between Enamel and Dentin Feldspathic Porcelain and Two Different Monolithic Zirconia with Low and High Translucency

Influence of operator variability on shear bond strength of self-etch adhesive to enamel with and without prior acid-etching

[Surface Roughness and Staining Stability of Infiltrant Resin for Enamel White Spot Lesion].

The Enamel Softening and Loss During Early Erosion Studied by Afm, Sem and Nanoindentation