Wavelength conversion based on high nonlinear microstructured fiber

Ming Chen,Juan Zhao,Tiansong Li,Shenyun Yu,Mingsong Chen

DOI: https://doi.org/10.1016/j.ijleo.2011.05.015

IF: 3.1

2012-01-01

Optik

Abstract:Abstract A wavelength conversion based on high nonlinear microstructured fiber is demonstrated. Core diameter and pitch of the microstructured fiber used in this wavelength conversion method are 2.05 μm and 5.0 μm, respectively. Diameter of the air-holes in the fiber cladding is 4.50 μm, the nonlinear coefficient of the microstructured fiber is 112.2 W −1 km −1 and it is 60 times higher than that of a conventional dispersion-shift fiber, the length of the fiber is 100 m. Four-wave-mixing effect is improved in the high nonlinear microstructure fiber and then the efficiency of the wavelength conversion is improved also. 10 Gbps Not-Return-to-Zero (NRZ) modulation format and 10 Gbps Return-to-Zero (RZ) modulation format are converted effectively by our method. This study can provide a new alternative solution for high effective all-light wavelength conversion in high speed optical communication systems with multi-wavelengths and all-light optical networks. PACS 42.79.Sz 42.65.Wi Keywords Wavelength conversion Four wave mixing Microstructured fiber 1 Introduction In recent years, a focus on the study of optical communication is All-Optical-Networks (AONs), and it is the necessarily developing result for network due to avoiding “electrical bottleneck” effect. The key techniques of AONs include all optical switching/routing, optical cross connection, all optical buffering and all optical wavelength conversion, and so on, where wavelength conversion can help reduce the blocking probability in all-optical wavelength division multiplexing (WDM) networks and can effectively resolve connection and dramatically increase network throughput. This is traditionally accomplished by converting the signal to the electrical domain and retransmitting it at another wavelength. Optical wavelength conversion has been demonstrated using many types of wavelength conversion techniques [1] . A key goal in any future WDM network is for the conversion approach to enable data transparency, as well as to be broadband, high-speed, low chirp, low additive noise, high efficiency and high data extinction radio [2] . Microstructured fibers [3–5] , also called photonic crystal fibers, with periodic transverse microstructure, can allow remarkable control of key optical properties such as dispersion, birefringence, nonlinearity and the position and width of the photonic band gaps (PBGs) in the periodic photonic crystal cladding. Microstructure fibers, with high nonlinearity, are today the most commonly used types of photonic crystal fibers. Their uses are within a wide filed of applications ranging from spectroscopy and sensor applications to the directly telecom oriented. The high nonlinear coefficient and designable dispersion properties makes these fibers for many nonlinear applications, such as supercontinuum generation, 2R regeneration, parametric amplifiers, pulse compression, all-optical switching, etc. [6,7] . The high nonlinear coefficient of the microstructured fiber may be a good solution for effective optical wavelength conversion techniques. In this paper, we demonstrate wavelength conversion method based on high nonlinear microstructured fiber. This fiber manufactured by FiberHome Technologies, Inc., of China. The numerical simulating software is Optisystem 6.0 from Optiwave, Inc. 2 Four-wave-mixing effect in the microstructured fiber Our demonstrated wavelength conversion method is based on four-wave mixing (FWM) effect [8] . So firstly, the four-wave mixing effect is discussed in brief. The origin of FWM effect lies in the nonlinear response of bound electrons of materials to an electromagnetic field. FWM effect is third-order parametric process with nonlinear interaction among four optical waves. Considering the fiber nonlinearity and multi-waves transmission, the total polarization P → can be written as: (1) P → = ɛ 0 ( χ ( 1 ) ⋅ E → + χ ( 2 ) : E → E → + χ ( 3 ) ⋮ E → E → E → + … ) , where ɛ 0 is the vacuum permittivity and is j th order susceptibility and is j + 1 rank tensor, E → is the electric field. The main features of FWM effect in microstructured fiber can be understood from the third order polarization term in Eq. (1) : (2) P → N L = ɛ 0 χ ( 3 ) ⋮ E → E → E → , where P → N L is the induced nonlinear polarization. Consider four continuous waves with frequencies ω 1 , ω 2 , ω 3 and ω 4 , respectively, and linearly polarized along the same axis x , the total electric field can be written as (3) E → = x ˆ 2 ∑ j = 1 4 E j e [ i ( β j z − ω i t ) ] + c . c ., where the propagation constant β j = ñ j ω j / c , ñ j is the mode index, x ˆ is the unit vector along the axis x and then Eq. (2) can be expressed as (4) P → N L = x ˆ 2 ∑ j = 1 4 P j e [ i ( β j z − ω i t ) ] + c . c .. New frequencies are produced by FWM effect in microstructured fiber, significant FWM effect occurs only if the phase mismatch nearly vanishes. This requires matching of the frequencies as well as of the wave vectors. The latter requirement is often referred to as phase matching. That is to say (5) ω 4 = ω i + ω j − ω k , (6) β 4 = β i + β j − β k . When ω i = ω j , it is called degenerate FWM effect, and then we have (7) Δ β = 2 β i − β k − β 4 . When pump light with high power and signal light were coupled into high nonlinear microstructured fiber, the nonlinear refractive index of the fiber core materials will be changed due to the Kerr nonlinearity effect, the phase mismatching factor Δ β is also changed with the change of power of the pump light. The modified phase mismatching factor must be introduced: (8) k = Δ β + γ ( P 1 + P 2 ) , where P 1 , P 2 are the power of the pump lights, γ = n ieff · ω p /( c · A eff ), n ieff is effective nonlinear index, ω p is angular frequency of the pump light, c is the vacuum light speed, A eff is the effective core area of the high nonlinear fiber. The phase-matching requirement is k = 0. For degenerate FWM effect, let P 1 = P 2 = P /2: (9) k = Δ β + γ P . As we know, in the near of the zero-dispersion wavelength of the fiber, the phase matching condition can be obtained if we let ω p = ω 0 , where ω 0 is the angular frequency of the zero-dispersion wavelength. However, to adequately utilize the high nonlinearity of the fiber, we obtain the phase matching condition and realize the effective wavelength conversion by changing the power of pump light. This will be described in detail in the following parts of this paper. 3 Wavelength conversion system and results A brief wavelength conversion system based on high nonlinear microstructured fiber is illustrated in Fig. 1 , the signal source and pump light are coupled by an optical coupler after a respective polarization control (PC) device and the merged light be send into an optical amplifier, and then the amplified light transmits into a high nonlinear microstructured fiber. After the microstructured fiber, an optical spectrum analyzer is followed, as showed in Fig. 1 . The FWM effect is polarization-dependent and this polarization-dependent is illustrated in Fig. 2 , the polarization states of the signal source light and pump light can be tuned by the two PC devices, as shown in Fig. 1 . Fig. 2 (A) denotes polarization direction of signal light is along that of the pump light (case A), (B) denotes polarization direction of signal light has 30° with that of the pump light (case B). The power of the idler light is higher about 12 dB in case A than that in case B. It can conclude that FWM effect is polarization-dependent, and we must make the polarization directions of the signal light and pump light in the same direction by careful modifying the two PC devices. Under this polarization condition, the output power of the idler light can obtain maximum power and the maximum conversion efficiency can be obtained. The cross structure of the microstructured fiber used in wavelength conversion is shown in Fig. 3 . The microstructure fiber is made of pure silica. It has a very small core in the center of the cross section. The core diameter and pitch of the fiber are 2.05 μm and 5.0 μm, the diameter of the air-holes in the fiber cladding is 4.50 μm. Large air holes are used so that the cladding has very high air-filling fraction. The fiber can confine the mode field very tightly in the small core region. The nonlinear coefficient is 112.2 W −1 km −1 , which is about 60 times higher than that of a conventional dispersion-shift fiber. The length of the used fiber is 100 m. The coupling technique of the optical fiber with the microstructured fiber is difficult due to the numerical aperture mismatch of the two kinds fibers. We developed new mode converter to reduce the big coupler loss, as shown in Fig. 4 . To splice a standard single-mode-fiber with the microstructure fiber as a pigtail, a high nonlinear fiber with appropriate core size is used between the standard single-mode-fiber and the microstructured fiber in this mode converter, the length and the core diameter of the high nonlinear fiber is 15 cm and 3.5 μm, respectively. The total splicing loss of one pigtail is 3.2 dB. The detailed system of the wavelength conversion is shown in Fig. 5 . Using a Mach–Zehnder (M–Z) modulator, the 10 Gbit/s electrical signal is modulated on the light carrier, which is emitted by a laser with wavelength 1550 nm. The modulated light from M–Z modulator is the signal source. The signal light and the pump light with wavelength 1549.66 nm from the pump laser are coupled by an optical coupler after respective PC device. The PC devices can modulate polarization direction of the signal light and the pump light. The merged light is send into optical amplifier, and then the amplified light transmits into the high nonlinear microstructured fiber. After the microstructure fiber, an optical coupler is followed. The light beam is split into two beams. One is sent to an optical spectrum analyzer, the other transmits into a PIN receiver after an optical filter. The central wavelength and bandwidth of the optical filter are the idler light (FWM light) wavelength and 0.40 nm, respectively. There is an oscillograph or a RF spectrum analyzer followed the PIN receiver. The oscillograph can show the transmitted signal waveform and the RF spectrum analyzer can show the signal spectrum. In this figure, the solid lines denote the light routes and the dashed lines denote the routes of the electrical signal. We study performance of the wavelength conversion system based on high nonlinearity microstructured fiber by transmitting two modulating formats electrical signals with 10 Gbps speed. There are NRZ (Non-return to Zero) format and RZ (Return to Zero) format. The waveforms of the input electrical pulses with NRZ format and the output those are shown in Fig. 6 , where Fig. 6 (a) denotes the input NRZ electrical pulses and Fig. 6 (b) denotes the corresponding output NRZ electrical pulses. We can find that the wavelength conversion system is effective for 10 Gbps NRZ format transmission. The corresponding eye diagram and RF spectrum of the output NRZ electrical pulses are shown in Fig. 7 . Fig. 7 (a) is the eye diagram and Fig. 7 (b) is the RF spectrum of the received 10 Gbps NRZ format electrical pulses. Some minimal fluctuations are produced in the “1” codes, this come from other nonlinear processes in the high nonlinear microstructured fiber, such as self-phase modulation (SPM) [2,8] . This will become very deleterious for continuous “1” codes especially, as shown in Fig. 6 (b). As a result, the upper part of the eye diagram becomes thick, as shown in Fig. 6 (a). The waveforms of the input electrical pulses with RZ format and the output those are shown in Fig. 8 , where Fig. 8 (a) denotes the waveform of input RZ electrical pulses and Fig. 8 (b) denotes the corresponding the waveforms of output NZ electrical pulses. We can find that the wavelength conversion system is also effective for 10 Gbps RZ format transmission. The corresponding eye diagram and RF spectrum of the output 10 Gbps RZ electrical pulses are shown in Fig. 9 . Fig. 9 (a) is the eye diagram and Fig. 9 (b) is the RF spectrum of the received 10 Gbps RZ format electrical pulses. 4 Conclusion and discussion A wavelength conversion method based on high nonlinear microstructured fiber is demonstrated. The core diameter and pitch of the fiber are 2.05 μm and 5.0 μm, the diameter of the air-holes in the fiber cladding is 4.50 μm. The nonlinear coefficient is 112.2 W −1 km −1 , which is about 60 times higher than that of a conventional dispersion-shift fiber. The fiber length is 100 m. Due to the very high nonlinearity of the microstructure fiber, we can obtain more effective wavelength converters with low pump power. This wavelength conversion system is effective for 10 Gbps NRZ modulation format transmission and 10 Gbps RZ modulation format. For 10 Gbps NRZ modulation format transmission communication system, some minimal fluctuations are produced in the “1” code, especially for continuous “1” codes, due to other nonlinear processes in the high nonlinear microstructure fiber except FWM effect. Because basing on FWM effect of high nonlinear microstructure fiber, our wavelength convertor can obtain transparent wavelength conversion for single wavelength or multi-wavelengths. This study may be a new alternative solution for high effective all-light wavelength conversion in high speed optical communication systems with multi-wavelengths and all-light optical networks. Acknowledgements The authors thank the Foundation of Guangxi Key Laboratory of Information and Communication, the Open Fund of Key Laboratory of Optical Communication and Lightwave Technologies, Beijing University of Posts and Telecommunications, Ministry of Education of China, for their supports. References [1] I.P. Kaminow T.Y. Li Optical Fiber Telecommunication. IV B. Systems and Impairments 2002 Academic Press San Diego [2] G.P. Agrawal Fiber-Optic Communication Systems 3rd ed. 2002 John Wiley & Sons, Inc. New York [3] B.J. Eggleton C. Kerbage P.S. Westbrook R.S. Windeler A. Hale Microstructured optical fiber devices Opt. Express 9 2001 698 713 [4] J. Toulouse Optical nonlinearities in fibers: review, recent examples, and systems applications J. Lightwave Technol. 23 2005 3625 3641 [5] M. Chen S. Xie New nonlinear and dispersion flattened photonic crystal fiber with low confinement loss Opt. Commun. 281 2008 2073 2076 [6] A. Bjarklev J. Broeng A.S. Bjarklev Photonic Crystal Fibers 2003 Kluwer Academic Publishers Press London [7] P. Russell History and future of photonic crystal fibres Proceedings of the OFC2009 OTuC1 2009 1 124 [8] G.P. Agrawal Nonlinear Fiber Optics 4th ed. 2007 Academic Press San Diego