Abstract:Results are presented on the fabrication and characterization of high critical temperature Josephson junctions in thin films of YBa2Cu3O7−δ produced by the process of focused electron-beam irradiation using 350 keV electrons. The junctions so produced have uniform spatial current densities, can be described in terms of the resistive shunted junction model, and their current densities can be tailored for a given operating temperature. The physical properties of the damaged barrier can be described as a superconducting material of either reduced or zero critical temperature (Tc), which has a length of ∼15 nm. The Tc reduction is caused primarily by oxygen Frenkel defects in the Cu–O planes. The large beam currents used in the fabrication of the junctions mean that the extent of the barrier is limited by the incident electron-beam diameter, rather than by scattering within the film. The properties of the barrier can be calculated using a superconductor/normal/superconductor (SNS) junction model with no boundary resistance. From the SNS model, we can predict the scaling of the critical current–resistance (IcRn) product and gain insight into the factors controlling the junction properties, Tc, and reproducibility. From the measured IcRn scaling data, we can predict the IcRn product of a junction at a given operating temperature with a given current density. IcRn products of ∼2 mV can be achieved at 4.2 K. The reproducibility of several junctions in a number of samples can be characterized by the ratio of the maximum-to-minimum critical currents on the same substrate of less than 1.4. Stability over several months has been demonstrated at room and refrigerator temperatures (297 and 281 K) for junctions that have been initially over damaged and then annealed at temperatures ∼380 K. Junctions manufactured using conventional lithography (0.5 μm wide) and which are suitable for digital electronics (Ic=500 μA at 40 K) can achieve IcRn products of 650 μV at 40 K. The production of 100 of these stabilized junctions could be accomplished in ∼4 h of irradiation time. The IcRn scaling also indicates that junctions suitable for high sensitivity superconducting quantum interference devices (Ic∼100 μA) can be made with IcRn products of ∼120 μV at 77 K.

Dynamic Range of High Temperature Superconducting Josephson Detecting Systems at Millimeter-Wave Band

Sensitivity of High Temperature Superconducting Josephson Detectors at Millimetre-Wave Band

A High-Temperature Superconducting Millimeter Wave Detecting System Based on Pulse Tube Cryocooler

Wideband frequency metrology using high temperature superconducting Josephson junctions

Terahertz Frequency Metrology Based on High-T-C Josephson Junctions

Terahertz Spectrometer Based on High Temperature Superconducting Josephson Junction

Small terahertz spectrometer based on high temperature superconducting Josephson junction

Intrinsic Noise Temperatures of YBa2Cu3O7−δ Josephson Devices on Bicrystal Substrates and the Upper Frequency Limit for Their Operation

Bolometric detection of Josephson radiation

Step-Edge Josephson Junctions on Multilayered High Temperature Superconducting Thin Film

Extraction of the Spectral Information of Terahertz Signals Using Superconducting Josephson Junction

HTS Josephson Junctions for THz Applications

A Tunable 350&#x2013;780 GHz CW Solid State Oscillator of Intrinsic Josephson Junctions in a High-T<inf>c</inf> Superconductor

Electron-beam damaged high-temperature superconductor Josephson junctions

Josephson Voltage Standard Circuit Operation with a Pulse Tube Cooler

Terahertz Responses of Intrinsic Josephson Junctions in High T(c) Superconductors.

Noise Figure Measurement of High Temperature Superconducting Bi-Crystal Josephson Junction THz Mixers

A Grain Boundary Josephson Junction As a Mixer to Evaluate Terahertz Emission from Intrinsic Josephson Junctions

Series YBCO Grain Boundary Josephson Junctions As a Terahertz Harmonic Mixer

Numerical Research on the Response of Josephson Junction with 0.14 THz Nanosecond Pulse Radiation